Welcome To INSTALLATION GUIDE 1
Contents Introduction......................................................... 3 In The Box........................................................... 4 Display................................................................. 5 Before You Start................................................... 6 Installation Overview........................................... 7 Professional Assistance........................................ 7 Abbreviations......................................................
In The Box - iDevices® Thermostat - Mounting Hardware Requires - Home Wi-Fi® Network - Free iDevices® Connected App - 24VAC Common Wire - Compatible Mobile Device (Visit iDevicesinc.
Installation Overview Before You Start 1. Read through this Installation Guide in its 1. Turn the power to your HVAC system OFF! entirety before starting installation of your 2. Remove the faceplate of your old thermostat iDevices® Thermostat or removal of your and photograph the existing old thermostat. Incorrect installation can be wiring configuration. dangerous and can damage your iDevices® 3. Disconnect your old thermostat’s wall Thermostat and HVAC system. If you’re not plate and secure the wires.
Abbreviations HVAC: Heating, Ventilation, and Air Conditioning system Terminal Assignments For reference, standard wiring assignments for typical HVAC systems are provided below. HP: Heat Pump System. This type of HVAC system uses a compressor with a reversing valve to provide both heating and cooling capability. HE: Electrically heated central heating system. This system uses an electric heating element along with a fan and ducting. Sometimes used as AUX/Emergency heat with a heat pump system.
Installation Details 1. Gather the tools you will need and check that your iDevices® Thermostat came with the necessary components (see page 4). Warnings And Safety Information Do not select COOL mode if the outside temperature is below 50ºF (10ºC). This could damage the cooling system. 2. Test your existing system. Using your old thermostat, turn on the heating/cooling functions (if applicable) to verify everything is functioning normally. 3.
Label Old Thermostat Wire Color Description Y2 Grey Stage 2 compressor relay Y1 Yellow Stage 1 compressor relay G Green Fan relay L C around a pen). Remove the mounting plate from the wall. 12. Line up the iDevices® Thermostat mounting plate on the wall in the desired location. Check that it is level and the wires are in a position to fit through the hole on the mounting plate. Use a pencil to mark anchor locations on the wall. System monitor Black/Blue Common of 24VAC transformer 9.
16. Connect the wires to the mounting plate based on the information you gathered in the chart on pages 11-12, photos you took earlier and wiring configuration you noted for step 15. 17. To prevent electrical shorts and damage to your iDevices® Thermostat or home, ensure all of the wire connections are secure and there are no bare wires in contact with another. Insulate bare wires with electrical tape as necessary. Push any excess wire back into the wall cavity. 18.
Thermostat on the home screen. Tap the ‘Menu’ button in the upper left-hand corner. From here, you can edit the details of your iDevices® Thermostat, organize it into a ‘Room’ and ‘Zone’, set schedules and create ‘Scenes’. Warnings And Safety Information Do not short across terminals on the gas valve or at the heating or cooling system control board to test the thermostat installation. This could damage the thermostat and void the warranty.
Wiring Configurations The following section provides the various wiring configurations compatible with the iDevices® Thermostat. Find the configuration that matches closely to your old thermostat and note which system type you have for later reference. Thermostat Settings Stage: Non-HP | Type: HE for electric, HG for gas/oil systems | Fan wire G baseboard optional for HG type Note: G wire is not required for hot water or steam radiator systems.
B. Heat Only (Two Stages) Note: G wire is not required for hot-water baseboard or steam radiator systems. If G wire is not connected for a warm air heating system, Fan On mode will not be available. C. Cool Only (One Stage) Thermostat Settings Stage: Non-HP | Type: HG Note: G wire is not required. However, if G wire is not connected, Fan On mode will not be available.
D. Cool Only (Two Stages) E. Heat (One Stage) and Cool (One Stage) Thermostat Settings Stage: Non-HP | Type: HE for electric, HG for gas/oil systems Thermostat Settings Stage: Non-HP | Type: Note: G wire is not required. However, if G wireHG is not connected, Fan On mode will not be available. Note: G wire is not required. If G wire is not connected, Fan On mode will not be available.
F. Heat (Two Stages) and Cool (One Stage) G. Heat (One Stage) and Cool (Two Stages) Thermostat Settings Stage: Non-HP | Type: HE for electric, HG for gas/oil systems Thermostat Settings Stage: Non-HP | Type: HE for electric, HG for gas/oil systems Note: G wire is not required. If G wire is not connected, Fan On mode will not be available. Note: G wire is not required. If G wire is not connected, Fan On mode will not be available.
H. Heat (Two Stages) and Cool (Two Stages) I. Thermostat Settings Stage: Non-HP | Type: HE for electric, HG for gas/oil systems Heat Pump (One Stage) Thermostat Settings Stage: HP | Type: HG | O/B Type: According to previous thermostat setting Note: G wire is not required. If G wire is not connected, Fan On mode will not be available. Note: G wire is not required. If G wire is not connected, Fan On mode will not be available.
J. Heat Pump (One Stage with AUX/ Emergency Heat) K. Heat Pump (Two Stages) Thermostat Settings Stage: HP | Type: HG | O/B Type: According to previous thermostat setting Thermostat Settings Stage: HP | Type: HE for electric, HG for gas/oil systems | O/B Type: According to previous thermostat setting Note: G wire is not required. If G wire is not connected, Fan On mode will not be available. Note: G wire is not required. If G wire is not connected, Fan On mode will not be available.
Troubleshooting & Support If your Thermostat doesn’t connect to your network or app on the first try, hold the reset button on the right side for 3 seconds using a paperclip. L. Heat Pump (Two Stages with AUX/ Emergency Heat) Thermostat Settings Stage: HP | Type: HE for electric, HG for gas/oil systems | O/B Type: According to previous thermostat setting Call or email the iDevices® Customer Experience Team with questions. Note: G wire is not required.