TouchSecure® Connectivity User Manual Ver2.
TouchSecure® Connectivity User Manual Version History Date 22-May-13 17-Jul-13 Version 1.0 2.0 Description of Changes Initial version 1. ICES-003 Statement removed. 2. French translation added for RSS-GEN 3. Added FCC statement IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.
TouchSecure® Connectivity User Manual Contents 1.0 Introduction ................................................................................................................................ 4 2.0 Reader ......................................................................................................................................... 4 2.1 2.2 2.3 Functionality..............................................................................................................................
TouchSecure® Connectivity User Manual 1.0 Introduction This document details the Physical Access Control Reader TouchSecure® and its basic operational and installation procedures. It covers the details of the Wallmount form-factor reader Model: Connectivity WM The reader comes in two variants for interfacing with the control panel • • Pigtail Phoenix connectors 2.0 Reader 2.1 Functionality TouchSecure® is a physical access reader that can read HF and LF contactless credentials .
TouchSecure® Connectivity User Manual 2.3 Back Plate 3.0 Product details Model Name : Connectivity WM Device Type : RFID reader, 13.56MHz (HF) / 125 KHz (LF) Physical Access control Reader (accessory equipment) Type of equipment : Potted reader.
TouchSecure® Connectivity User Manual 5.0 Installation details 5.1 Parts List • • • • TouchSecure® reader -1 Screws (A #6-18X1.5" SS ) - 4Nos – Back Plate mounting screws for Wall Snake Eye Screw (SMF #6-32X5/16" SS) – 1 No- Top casing mounting security screw Screws (SMF #6-32x3/8" SS) - 3 No’s - 1 casing to back plate mounting screw and 2 Junction Box mounting screws Nylon anchor plug -4 Nos 6 pin phoenix plug (Phoenix connector version only) – 2 Nos Back Plate • • • 5.
TouchSecure® Connectivity User Manual 5.3.2 Pin P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P2.1 P2.2 P2.3 P2.4 P2.5 P2.
TouchSecure® Connectivity User Manual 5.4 Mounting the Reader 5.4.1 Location of mounting holes on wall Phoenix connector Reader – 4 Holes and 1 Slot 5.4.2 Reader Installation Steps a. b. c. d. Make holes on the wall as per the image above. Insert the nylon screw plugs into the wall. Connect the wires as per the Table 2 or Table 3. TouchSecure® reader with Bottom Casing is to be now secured onto the wall using the Screws (A #6-18X1.5" SS ) e. The top casing can be inserted onto the bottom casing f.
TouchSecure® Connectivity User Manual Reader Installation Steps - Phoenix Connector Version Reader Installation Steps - Pig Tail Version IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.
TouchSecure® Connectivity User Manual 5.5 Power up and Testing 1 Turn power on The LED blinks 3 times green with a long beep, then turns red 2 Present a card The LED blinks green, and a short Beep is emitted This is the default reader behavior. 6.0 Certifications 6.1 FCC This device complies with Part 15 of the FCC Rules.
TouchSecure® Connectivity User Manual 6.3 CE Identive hereby declares that the TouchSecure® Model: Connectivity WM device mentioned herein is in compliance with the essential requirements and other relevant portions of the Directive R&TTE 1999/5/EC. IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.