IDENTEC SOLUTIONS i-B350L -CC HARDWARE USER MANUAL
i-B350L -CC – Hardware User Manual | 20. September 2019 Proprietary Notice This document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used or disclosed to other parties in whole or in part without the prior written authorization from IDENTEC SOLUTIONS.
i-B350L -CC – Hardware User Manual | 20. September 2019 Radio Frequency Compliance Statement IDENTEC SOLUTIONS is the responsible party for the compliance of the following devices: MODEL: i-B350L CC Region/Country Organization Marking EUROPE: EU CE USA: FCC CANADA: Industry Canada FCC ID: OO4-ILR-IB350LCC 3538A-IB350LS The user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, by IDENTEC SOLUTIONS.
i-B350L -CC – Hardware User Manual | 20. September 2019 WARNING - This product should be installed by personnel trained in installation of equipment in industrial environments and meet the representative country’s National Electrical Code. Electrostatic Discharge This product contains components that are sensitive to electrostatic discharges. Please observe the special instructions for their protection. Incorrect handling can damage the unit and cause the invalidation of the warranty.
i-B350L -CC – Hardware User Manual | 20. September 2019 Safety Instructions The system described in this manual is for exclusive operation of trained employees. Only qualified personnel that have knowledge of the potential dangers involved should perform the installation, settings, maintenance and repair of the units used.
i-B350L -CC – Hardware User Manual | 20. September 2019 Contents 1. Preface .................................................................................................................................................................... 7 2. Introduction .............................................................................................................................................................. 8 2.1 General Information ...................................................................
i-B350L -CC – Hardware User Manual | 20. September 2019 1. Preface This installation manual must be read carefully prior to starting the installation. The described installation works assuming that installation materials like cables, antennas and any mechanical parts are available. This document is the hardware description of the i-B350L CC. This document is intended only for mechanical and electrical installation of these central units.
i-B350L -CC – Hardware User Manual | 20. September 2019 2. Introduction 2.1 General Information The ILR i-B350L CC active RFID broadcast tag transmits data over 500 meters in predetermined intervals. The credit card holder housing provides mounting possibilities for an ID card and is ideally suited for personnel safety applications.
i-B350L -CC – Hardware User Manual | 20. September 2019 2.3 System Components — Readers i-PORT M352 UHF The i-PORT M352 UHF is used as a reader in Identec’s system. It can be connected to the host PC software via several different interfaces (RS422, Ethernet, Power-over-Ethernet). It communicates with the ILR® Tags wirelessly up to a distance of up to 500 meters.
i-B350L -CC – Hardware User Manual | 20. September 2019 2.4 System Components—Antennas Only approved antennas should be used. Other antennas not provided by IDENTEC SOLUTIONS may void permit of use and violate compliance regulations. Omnidirectional sub-1GHz Antenna Dimensions Half-wave Dipole Antenna Ordering number: - 289070 Half-wave Dipole Antenna SMA i-CTA868 MHz – (CTA 868/2/DR/SM/S2) Orientation Diagrams Elevation Vertical Polarization Copyright © 2019 IDENTEC SOLUTIONS. All rights reserved.
i-B350L -CC – Hardware User Manual | 20. September 2019 3. Configuration of the Tag 3.1 General The i-B350L CC is configured using the i-PROG M350L programming device. Important Note Do not open the housing! Configuration is done using the built-in air interface of the i-B350L CC.
i-B350L -CC – Hardware User Manual | 20. September 2019 • Broadcast Message Options: The options in this field depend on the capabilities of the tag. • User Data Length: Configure the number of Bytes from the “User Data” that is sent with a broadcast message. The number starts from Byte 0 (zero). Please pay attention to the limits of the User Data Length described at the end of this chapter. 3.
i-B350L -CC – Hardware User Manual | 20. September 2019 The last row shows how the random use of the timeslot avoids collision between the tags. Copyright © 2019 IDENTEC SOLUTIONS. All rights reserved.
i-B350L -CC – Hardware User Manual | 20. September 2019 4. Troubleshooting This chapter covers how faults can be recognized and rectified. There are potentially four main problem sources: The user control system, including task requirements, communication cables, peripheral units with possible object recognition switches. The SensorSMART platform including peripheral units and their cables, also potential object recognition switches.
i-B350L -CC – Hardware User Manual | 20. September 2019 6.