MorphoAccess® VP Series - User Guide Table of figures Table of figures Figure 1: Minutiae are classified in two categories: ridge ending and bifurcation .................................. 12 Figure 2: Vascular pattern image processing............................................................................................ 13 Figure 3: areas of interest .........................................................................................................................
MorphoAccess® VP Series - User Guide Section 1: Introduction Section 1: Introduction 7 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 1: Introduction MorphoAccess® VP Terminal Congratulations for selecting the MorphoAccess® VP Series, first ever Physical Access Control terminals to integrate the state of the art multimodal technology combining finger vein and fingerprint biometrics.
MorphoAccess® VP Series - User Guide Section 1: Introduction Scope of the document This guide deals with the use of the MorphoAccess® VP Series, which is made up of following list of products. MorphoAccess® VP Series 9 Multimodal Biometrics Contactless Smartcard Reader MIFARE™ DESFire™ MorphoAccess® VP-Bio Yes No No MorphoAccess® VP-Dual Yes Yes Yes MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 1: Introduction Safety instructions The installation of this product should be made by a qualified service Person and should comply with all local regulations. It is strongly recommended to use a class II power supply at 12V ±5% and 1A min according with Safety Electrical Low Voltage (SELV). The 12V power supply cable length should not exceed 3 meters.
MorphoAccess® VP Series - User Guide Section 1: Introduction interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna.
MorphoAccess® VP Series - User Guide Section 1: Introduction About Biometrics About fingerprint biometrics Fingerprints are permanent and unique. They are formed before birth and last throughout one's life. Classification and systematic matching of fingerprints for different purposes have been in use since the late 19th century. Figure 1: Minutiae are classified in two categories: ridge ending and bifurcation Present on your fingers is skin, which is different from that on other areas of your body.
MorphoAccess® VP Series - User Guide Section 1: Introduction About finger vein biometrics Vascular pattern recognition is a relatively recent activity in the field of biometrics. The reason is that only recently has one been able to observe the vascular pattern of a living human being in a convenient, non-invasive way. The first paper opening the way to this kind of observation was published in the early nineties.
MorphoAccess® VP Series - User Guide Section 1: Introduction Multimodality and its advantages Performances in terms of accuracy (characterized by the FRR @FAR ratio) remain one of the main challenges of the biometric industry. But once a biometric technology has reached maturity, time and efforts in research required to carry out improvements to the performances (e.g. by refining algorithms) are significant.
MorphoAccess® VP Series - User Guide Section 1: Introduction • matching accuracy is increased, reducing the probability to reject genuine individuals and to accept impostors. Thanks to low False Reject Rates even for very demanding False Acceptance Rates (@ FAR=10-4, multimodal FRR is ten times lower than the one of the best modality), MorphoAccess® VP Series is the common answer to comfort and security concerns in any biometric application.
MorphoAccess® VP Series - User Guide Section 1: Introduction Acquisition principles Areas of interest As regards fingerprint, the area containing the most relevant biometric data is usually located in the centre of the first phalanx. As regards blood vessel pattern, the area of interest is usually located between the first and the third phalanxes. Figure 3: areas of interest Ergonomics Image acquisition is performed with CMOS camera.
MorphoAccess® VP Series - User Guide Section 1: Introduction The vein pattern imaging process requires finger’s second phalanx not to be in contact with the device. A finger root guide (3) has been designed to hold finger into a flat position in order to avoid any contact inside the vein imaging active area. It is highly recommended to wipe the device transparent surface with a dry cloth in case it is wet.
MorphoAccess® VP Series - User Guide Section 1: Introduction Enrollment process The level of care taken during enrollment phase will impact all the next steps of the biometric recognition chain. So it is absolutely necessary to teach individuals how to use properly the device according to the rules stated below, in order to acquire the best image quality. This will result at the end in the best quality of service.
MorphoAccess® VP Series - User Guide Section 2: MorphoAccess® VP Series terminal presentation Section 2: MorphoAccess® VP Series terminal presentation 19 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 2: MorphoAccess® VP Series terminal presentation Interfaces description Introduction The MorphoAccess® VP Series Installation Guide document describes precisely each interface and connection procedure. Note that all connections of the MorphoAccess® VP Series terminal described hereafter are of SELV (Safety Electrical Low Voltage) type.
MorphoAccess® VP Series - User Guide Section 2: MorphoAccess® VP Series terminal presentation Power supply interface (see figure 7) The terminal can be powered by two different ways: • Either by the two wires block +12V DC/GND • Or by the Power Over Ethernet function, using the RJ45 connector, or the 5-wires block. Power Over Ethernet The MorphoAccess® VP terminal can be powered through the Ethernet interface using POE (Power Over Ethernet) feature.
MorphoAccess® VP Series - User Guide Section 2: MorphoAccess® VP Series terminal presentation Figure 7: MorphoAccess® VP Series terminal rear view (connectors) SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 2: MorphoAccess® VP Series terminal presentation Figure 8: MorphoAccess® VP Series terminal front view, without bottom cover 23 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 2: MorphoAccess® VP Series terminal presentation Access control systems interface (see figure 8) The terminal provides several interfaces for an easy integration into a global access control system. Sending of a message at the end of local access control The terminal is able to send a message to a distant system when local checks are completed.
MorphoAccess® VP Series - User Guide Section 2: MorphoAccess® VP Series terminal presentation USB port usage Plugging a USB Mass storage key The front USB port of the MorphoAccess® terminal is dedicated to the connection of a USB Mass Storage key, to configure the terminal with command scripts.
MorphoAccess® VP Series - User Guide Section 2: MorphoAccess® VP Series terminal presentation Plugging a USB Wi-Fi™ adapter The front USB port of the MorphoAccess® VP Series terminal is dedicated to the connection of a Wi-Fi™ USB adapter. The bottom cover must be removed to allow the access to the USB port. Figure 10: MorphoAccess® VP Series terminal USB port with a Wi-Fi™ adapter SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC Section 3: Connecting a MorphoAccess® to a PC 27 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC Introduction Why connecting a MorphoAccess® terminal to a PC The MorphoAccess® VP Series terminal is designed to be able to run in standalone mode, it means without any connection to a master system.
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC Point to Point Ethernet Connection The MorphoAccess® terminal can be connected directly to a PC by an Ethernet cable. But there are some limits: • if the PC Ethernet port doesn’t support the Auto-MDIX feature, then a crossover Ethernet cable is mandatory. If no crossover Ethernet cable is available, then a switch can be used (please refer to next section).
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC Connection through only one Ethernet switch The MorphoAccess® terminal can be connected to a PC through an Ethernet switch. This is useful when no crossover cable is available, but instead, one Ethernet switch and two Ethernet standard cables are available. WARNING: an Ethernet HUB doesn’t allow a connection between two of its ports. An Ethernet switch is really mandatory.
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC Connection through a LAN Description The MorphoAccess® terminal can be connected to a PC through a Local Area Network (LAN). The MorphoAccess® terminal required for a connection is specified by its IP address or by its host name, if it can be added to the DNS Server database. The IP address is either static, or dynamically assigned by the DHCP server of the network.
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC LAN without DNS Server This section is about LAN without DNS Server, or with DNS Server but the MorphoAccess® terminal host name cannot be added to the DNS Server base. In that case the PC is not able to establish a connection with a MorphoAccess® terminal using its host name. The IP address of the MorphoAccess® terminal is the only way to specify the terminal.
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC Setting up IP parameters with a USB Mass Storage Key The IP configuration parameters can be set by using a USB mass storage key. No wired connection with a PC is required. This operation requires a standard USB Mass Storage key (FAT16 or FAT32 formatted, and 8 Gbyte maximum), and a dedicated PC application: USB Network Configuration Tool.
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC First select either DHCP mode (IP address allocated dynamically), or static s mode (static IP address).
MorphoAccess® VP Series - User Guide Section 3: Connecting a MorphoAccess® to a PC Wi-Fi™ Network configuration Requirements Wi-Fi™ connection is available under the following mandatory conditions: • a Morpho Wi-Fi™ USB adapter must be plugged in the front USB port of the terminal (the bottom cover must be removed to give access to this port).
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration Section 4: MorphoAccess® Terminal Configuration SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration MorphoAccess® configuration parameters Presentation The name and the value of the MorphoAccess® terminal parameters (also named "configuration keys") are located into different files composed of several sections, to group configuration keys by affinity. For example a file named "app.
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration Configuring a connected MorphoAccess® terminal Introduction A MorphoAccess® terminal can be managed by a PC connected to the terminal, using an application such as MEMS, Configuration Tool, MATM, or MorphoEnroll.
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration Configuration Tool PC application The Configuration Tool application is able to read and modify any MorphoAccess® terminal parameter. Figure 18: MorphoAccess® configuration tool main window Please refer to MorphoAccess® Configuration Tool User Guide document for further information about this PC application.
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration SSL securing The TCP link used for remote management can be secured using SSL protocol. Please refer to SSL Solution for MorphoAccess® document for further details. SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration Upgrading the firmware When required, the MorphoAccess® terminal firmware can be upgraded from a PC, through an IP link (either Ethernet or Wi-Fi™) or using a USB mass storage key. The last MorphoAccess® terminal firmware can be obtained on a CD/ROM package from the customer service, or can be downloaded from Morpho Website dedicated to biometric terminals: http://www.biometric-terminals.
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration MorphoAccess® terminal database management Introduction The management of the MorphoAccess® terminal internal biometric database can be done remotely by an Enrolment Station, typically with a PC with MorphoEnroll application, or with MEMS application, or with an application developed with ActivMaci library.
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration MorphoAccess® terminal license management Definition of a license A license unlocks the additional features of the MorphoAccess® terminal. The MorphoAccess® VP Series terminal supports two licenses: • MA 10K USERS, • MA_WIFI. The feature unlocked by each license is detailed in sections below.
MorphoAccess® VP Series - User Guide Section 4: MorphoAccess® Terminal Configuration Please refer to document MorphoAccess® Terminal License Management for more information). SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 5: Access Control Section 5: Access Control 45 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 5: Access Control Access control presentation Typical architecture of an access control system Typical access control system architecture includes: • one MorphoAccess® terminal per area to protect • an Enrollment Station dedicated to user enrollment, and database synchronization with all MorphoAccess® terminals (it could be a PC with MEMS application) • a Central Security Controller : for area access final check, and physical access command (open the door) Figu
MorphoAccess® VP Series - User Guide Section 5: Access Control Typical access control process 1. All allowed user must be enrolled by the enrolment station. It means that the enrolment station creates a record for each allowed user. This record includes the biometric data of two of the user’s fingers. 2. When required, the Enrolment Station adds new user records into each MorphoAccess® terminal, and removes obsolete user records. 3.
MorphoAccess® VP Series - User Guide Section 5: Access Control MorphoAccess® terminal operating modes Standalone mode or Slave mode The MorphoAccess® terminal supports two exclusive operating modes: • The Standalone Mode: the MorphoAccess® terminal manages the access control alone, or with the help of a central access controller. • The Proxy Mode: the access control application is located in a distant system which drives the MorphoAccess® terminal as a slave device.
MorphoAccess® VP Series - User Guide Section 5: Access Control How to select the standalone access control process The chart below describes the different processes available and the related configuration keys. Figure 20: Recognition mode synthesis Identification and one authentication processes can be activated at the same time, as described in Section 8: Multi-factor mode section. 49 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 5: Access Control Access control result Information for the user The MorphoAccess® terminal communicates the result to the user, by a local audible and visible signal. These signals are described in the Section 11 Man Machine Interface section.
MorphoAccess® VP Series - User Guide Section 5: Access Control Access granted Figure 21: Access control result = access granted Access denied Figure 22: Access control result = Access denied 51 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 6: Access Control by Identification Section 6: Access Control by Identification SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 6: Access Control by Identification Identification mode description Identification process The identification process consists in retrieving the identity of an unknown person, by comparison of a personal data with a base which contains the same type of personal data of known persons. At the end of the process, the person is either identified (identity found), or still unknown.
MorphoAccess® VP Series - User Guide Section 6: Access Control by Identification Compatibility with Access Control Systems When the identification mode is activated, the MorphoAccess® terminal supports the optional features listed below: • Internal relay activation when the access is granted, as described in Internal Relay activation on Access Granted result section • External activation of the internal relay, as described in Internal Relay activation by external button section • Send access control result
MorphoAccess® VP Series - User Guide Section 6: Access Control by Identification User Interface In this mode, the MorphoAccess® terminal waits for the placement of a finger on the biometric sensor. This state is displayed to the user by a specific signal, as described in Terminal states section. To request the access, the user places his finger on the biometric sensor: this action starts the identification process.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Section 7: Access control by Authentication SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Authentication process Introduction The MorphoAccess® terminal offers an authentication mode designed to works with contactless smart cards used as personal cards. Then this section relates to only MorphoAccess® terminals equipped with a contactless smartcard reader (see section Scope of the document). In the whole document the word “card” means “contactless smart card”.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication When it is required, the biometric check compares the biometric data of the finger placed on the sensor with the reference biometric data of two fingers of the user, acquired during enrollment process. If a match is found, the result of the biometric check is positive: user’s identity is confirmed. Otherwise, the result of the biometric check is negative: user’s identity is not confirmed.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Manual bypass of biometric control The default configuration of authentication mode requires a biometric control. But the biometric check can be disabled by the MorphoAccess® terminal administrator.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Selection of user’s contactless card type (MIFARE™ or DESFire™) Contactless Card type As MorphoAccess® terminals are equipped with a contactless smartcard reader compatible with MIFARE™ and DESFire™ cards (see section Scope of the document), it is possible to specify the type of card to be supported by the terminal: • Only MIFARE™ cards: for example when the terminal replaces a MorphoAccess® 120 terminal.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Biometric check, biometric data on user’s card Description In this mode, each user's card contains an identifier and the biometric data of two different fingers of the user. The terminal compares the biometric data of the finger placed on the biometric sensor, with the biometric data found on the user’s card. If a match is found, the access is granted, otherwise the access is denied.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication User interface The authentication process starts when the user presents his contactless card in front of the terminal. If the terminal found the required data on the user’s card, then the user is invited to place his finger on the biometric sensor, for biometric authentication.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Biometric check, biometric data in local database Description In this mode, each user's card contains only an identifier. The biometric data of two different fingers of the user are stored in the internal database, with the same user’s identifier as the one on the user’s card. The terminal compares the biometric data of the finger placed on the biometric sensor, with the user’s biometric data found in the database.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication User Interface The authentication process starts when the user presents his contactless card in front of the terminal. If the terminal found the required data on the user’s card (the user’s identifier), it search for the user’s record, in the internal database.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication No biometric check, no user id check Description This authentication mode is the version of the “Biometric check, biometric data on user’s card authentication mode with biometric check disabled. The terminal searched only for the user’s identifier on the user’s card. No other check is performed : the user’s identifier is not searched in the local database, and there is no biometric check.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication User Interface The authentication process starts when the user presents his contactless card in front of the terminal. Figure 27: Authentication without biometric check, and without User ID check The authentication process succeeds if the user’s identifier is found. Otherwise, the authentication process fails.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication No biometric check, but User ID check Description This authentication mode is the version of the “Biometric check, biometric data in local database” authentication mode, when biometric check is disabled. The user’s identifier is the only data read on user’s card. The MorphoAccess® terminal checks if the user’s identifier exists in the database.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication User Interface The authentication process starts when the user presents his contactless card in front of the terminal. Figure 28: Authentication without biometric check, and without User ID check The user’s identifier is read on the user’s card and searched in the local database. The authentication process succeeds if the user’s identifier is found in the local database. Otherwise, the authentication process fails.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Authentication process specified by User’s card Description When this mode is enabled, the access rights check to perform is specified by a dedicated data on user’s card.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication User Interface Start The authentication process starts when the user presents his contactless card in front of the MorphoAccess® terminal. The terminal searches on the user’s card, for the data that indicates if the biometric check is mandatory or disabled. If this data is found, the terminal executes the required process.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Allowed format for User’s identifier TLV structured data The user’s identifier is stored in ASCII within a TLV structure. User’s identifier stored in TLV format app/contactless/data format = 0 TLV structure app/contactless/data length=0.0 Automatic size app/contactless/data offset= 0.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication ISO14443 type A UID Description The MorphoAccess® terminal is able to use the ISO 14443 type A Card UID, as user’s identifier. This Card UID is available from any MIFARE™ cards and from any DESFire™ cards. The Card UID can be read either in most significant byte first (MSB) order, or in less significant byte (LSB) order. Card type compatibility This format can be only used only with the “MIFARE™ only default mode”.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication Binary data Description The MorphoAccess® terminal is able to use as user’s identified, a binary value to read on specific location on user’s card. This binary value could be the serial number of the card, as explained in the Example: MIFARE™ card Serial Number used as user’s identifier section. The MorphoAccess® terminal is able to read a binary value which is not aligned on complete bytes.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication bytes].[additional bits] identifier (15 bytes maximum) app/contactless/data type Byte read acquisition method: either little or big endian. 0.1 (binary data, MSB first) 0.0 (binary data, LSB first) Example: MIFARE™ card Serial Number used as user’s identifier In this sample the terminal read the first four byte, in MSB direction, of the first sector of the MIFARE™ card which contains the serial number of the card.
MorphoAccess® VP Series - User Guide Section 7: Access control by Authentication app/contactless/data length = 4.0 Size = 4 bytes app/contactless/data offset = 0.
MorphoAccess® VP Series - User Guide Section 8: Multi-factor mode Section 8: Multi-factor mode SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 8: Multi-factor mode Multi-factor mode Description When the identification mode and one of the contactless card authentication modes are activated, then the terminal is in “multi-factor” mode. User Interface It means that the user is allowed to choose the access right control to be processed by the terminal: • If the user places his finger first on the sensor, then it is identification process which is executed.
MorphoAccess® VP Series - User Guide Section 8: Multi-factor mode Activation of multi-factor mode app/bio ctrl/identification =1 Enabled app/bio ctrl/authent card mode = 1 or app/bio ctrl/authent ID contactless = 1 or app/bio ctrl/authent PK contactless = 1 Enabled SSE-0000082427-01 January 2011 Enabled Enabled MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 9: Proxy (or slave) Mode Section 9: Proxy (or slave) Mode 79 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 9: Proxy (or slave) Mode Description Scope The Proxy mode is an operating mode where the access control main application is located in a distant system. This is not a standalone mode like Identification and Authentication modes. It means that the terminal becomes a slave of the host system application.
MorphoAccess® VP Series - User Guide Section 9: Proxy (or slave) Mode Local signals When the terminal is waiting for a command from the distant system, there is none local signal: the status LED is off, the sensor backlight is off, the buzzer is off. But when a command is in progress the terminal emits the signals related to the function. It is the same signals as the standalone modes.
MorphoAccess® VP Series - User Guide Section 9: Proxy (or slave) Mode Proxy mode activation The proxy mode is automatically enabled when the identification mode and all authentication modes are disabled.
MorphoAccess® VP Series - User Guide Section 10: MorphoAccess® Terminal Customization Section 10: MorphoAccess® Terminal Customization 83 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 10: MorphoAccess® Terminal Customization Number of biometric check attempts Description In order to reduce the False Rejection Rare, the terminal allows the user to place again his finger on the sensor for a 2nd try, when the initial biometric check fails. This 2nd try is allowed by default, but can be disabled. The 2nd try allows the user to upgrade the finger placement, or to place another finger.
MorphoAccess® VP Series - User Guide Section 10: MorphoAccess® Terminal Customization Setting up matching threshold Description The performances of a biometric system are mainly characterized by two values: • The False Reject Ratio (FRR) : number of wrongly rejected allowed users, divided by the number of access requests • The False Acceptance Ratio (FAR) : number of wrongly admitted not allowed users, divided by the number of access requests Both ratio values are linked.
MorphoAccess® VP Series - User Guide Section 10: MorphoAccess® Terminal Customization Matching threshold values are detailed in the table below: Value FAR value 0 Lowest threshold value: the number of false rejects is very low, but the number of false acceptances is too high for a secure usage. It is strongly advised to don’t use this value, because the terminal becomes too tolerant. 1 FAR < 1 % 2 FAR < 0.5 % 3 FAR < 0.1% Recommended value for physical access control application 4 FAR < 0.
MorphoAccess® VP Series - User Guide Section 10: MorphoAccess® Terminal Customization Anti-tamper and anti-pulling switches Description The MorphoAccess® VP Series terminal is able to detect two kinds of unusual events: • the front glass is removed, by monitoring anti-tamper switches • the terminal is removed from the wall, by monitoring the anti-pulling switches When one of those events is detected, the MorphoAccess® VP Series terminal acts as required by the related configuration key (see section below):
MorphoAccess® VP Series - User Guide Section 10: MorphoAccess® Terminal Customization Please refer to the MorphoAccess® VP Series Installation Guide for more information about the anti-tamper and the anti-pulling switches. Configuration keys The action(s) to be performed by the MorphoAccess® terminal is defined by a unique dedicated configuration key.
MorphoAccess® VP Series - User Guide Section 10: MorphoAccess® Terminal Customization Example 1: send alarm message in Wiegand, and output local alarm signal In case of anti-tamper or anti-pulling detection, the terminal must: • Send an alarm message to a distant system, using Wiegand protocol. The identifier (error code) of the alarm message is 62221. • Emit a local alarm signal.
MorphoAccess® VP Series - User Guide Section 10: MorphoAccess® Terminal Customization Multimodal Security level Description The MorphoAccess® VP Series terminals allow to select the security level of the multimodal biometrics. Configuration key The multimodal biometrics security level is selected by only one configuration key. Multimodal biometrics security level app/bio ctrl/security level = 0 Standard security level (default value) app/bio ctrl/security level = 1 High security level.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Section 11: Compatibility with an Access Control System 91 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Internal Relay activation on Access Granted result Description If the result of the access rights check is successful, the internal relay may be optionally activated, for example, to directly trigger a door switch. The duration of the activation of the internal relay can be modified by a specific configuration key.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System The default state of the relay can also be defined. Relay default state 93 app/relay/relay default state = 0 Open (default) app/relay/relay default state =1 Close MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Internal Relay activation by external button Description This feature enables to activate the internal relay of the MorphoAccess® terminal using the LED1 signal input, in addition to normal activation on access granted result. It means either a successful recognition or a signal on LED1 activate the internal relay.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Access request result log file Description When enabled, the terminal creates a record for each access request in a local log file. Each record includes: • the date and the time of record creation (when access control result is known), • the user’s identifier (if available) • the access control process executed (Identification, Authentication with biometric check, ..
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Activation key The creation of a record for each access request is enabled (and disabled), by only one configuration key. Enabling recording of all access request results in the internal log file app/log file/enabled = 1 Enabled app/log file/enabled = 0 Disabled SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Sending the access control result to a distant system Presentation After access control rights check, the MorphoAccess® terminal can send a message which contains the result of the control, to a distant device (such as a Central Security Controller). The MorphoAccess® terminal is able to use different channels and different protocols, to send this message.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Wiegand protocol The Wiegand frame includes only the user identifier (which must be a numeric value). By default, the access control result message is sent only when the user is identified or authenticated. But as an option this access control result message can be sent when the access is denied, but with a numeric error code instead of the user identifier value.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Ethernet port Protocol selection The protocol used to send the message through the Ethernet link, must be only one of these protocols: UDP or TCP or SSL. UDP protocol Same comment as for RS485 protocol. Send access control result message using UDP protocol on Ethernet port app/send ID UDP/enabled = 1 Enabled app/send ID UDP /enabled = 0 Disabled TCP protocol Same comment as for RS485 protocol.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Note about terminal clock deviation The message send through IP and RS485 includes the date/time of access control result. The terminal clock has a +/- 4 sec per day typical time deviation at +25°C. At 50°C, the time deviation may be up to -8 sec per day.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System LED IN feature Description When this feature is activated, the terminal waits for an answer from a distant system, before granting the access. If no answer is received the access is denied even of the biometric check is positive. This feature is to be use in addition to the Sending the access control result to a distant system function.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Then to reduce the user wait time, the value of the wait time for GND1/GND2 signal must be defined to value a little bit greater than maximum controller answer delay.
MorphoAccess® VP Series - User Guide Section 11: Compatibility with an Access Control System Time mask feature Description The MorphoAccess® terminal provides a feature that enables to deny the access to a normally authorized user, on the base of time of access request. One typical application is to allow the access during regular working hours, and to deny the access to the same user during closed hours (night, week end). This feature is compatible with MEMS and MorphoEnroll applications.
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Section 12 MorphoAccess® VP Series terminal sound and light Interface SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Light and sound signals Light signal description Intermittent "Pulse": 1 second OFF and 0.5 second ON Sample Intermittent blue "Pulse" Fast intermittent "Pulse": 0.5 second OFF and 0.5 second ON.
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Signals table Terminal status Status Biometric Status LED Sensor Buzzer Waiting for a finger OFF OFF OFF Waiting for a badge OFF BLUE OFF Waiting for a finger or a card OFF BLUE OFF Bad finger placement OFF Intermittent YELLOW pulse OFF Finger removed too quickly OFF YELLOW OFF Finger acquisition running GREEN OFF OFF No database or empty database OFF Intermittent YELLOW p
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Terminal states Identification or Authentication - Waiting for a finger on the sensor The identification mode is activated, and the MorphoAccess® terminal is waiting for the placement of a finger on the biometric sensor.
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Multi-factor mode - waiting for user’s finger or user’s card The identification mode, and one of the authentication modes are activated, and the MorphoAccess® terminal is waiting for the placement of a finger on the biometric sensor or for the presentation of a contactless card.
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Proxy mode - waiting for distant system command When the proxy mode is enabled and when the terminal is expecting for a command from the distant system, there is no local signal Biometric Sensor backlight OFF Status LED OFF Buzzer OFF Biometric Sensor start up error The terminal fails to start the biometric sensor.
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Maintenance: Biometric Sensor firmware update This signal is emitted when the biometric Sensor firmware update is in progress. This update occurs only at first start up of the terminal after a terminal firmware update.
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Access request result Identification or Authentication - Access granted The user is recognized and the access is allowed.
MorphoAccess® VP Series - User Guide Section 12 MorphoAccess® VP Series terminal sound and light Interface Finger removed too earlier The terminal emits this signal if the finger is removed too earlier, while the finger biometric data acquisition is in progress. Biometric Sensor backlight OFF Status LED Yellow 1s Flash Buzzer OFF SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 13: Compatible Accessories, Software Licenses and Software Applications Section 13: Compatible Accessories, Software Licenses and Software Applications 113 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Section 13: Compatible Accessories, Software Licenses and Software Applications Compatible accessories & software licenses The following items can be ordered directly toMorpho or official distributor, so as to enjoy all the features of your MorphoAccess® VP Series terminal: • Power supply units • Contactless smartcards: MIFARE™ 1K or 4K ; DESFire™ 2K, 4K or 8K • MA WI-FI PACK, containing a Wi-Fi™ USB dongle and a Wi-Fi™ license to activate Wi-Fi™ capability on your term
MorphoAccess® VP Series - User Guide Section 13: Compatible Accessories, Software Licenses and Software Applications Compatible software applications MorphoAccess® VP Series terminals are fully compatible with: • MorphoAccess® Enrolment & Management System (MEMS) application • Morpho Integrator’s Kit (MIK) software development kit • MorphoEnroll enrolment application 115 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Appendix 1: Finger placement rules Appendix 1: Finger placement rules SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Appendix 1: Finger placement rules Finger placement recommendations 117 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Appendix 1: Finger placement rules To ensure a good acquisition quality, please leave the finger on the biometric sensor until the backlight is turned off.
MorphoAccess® VP Series - User Guide Appendix 2: Bibliography Appendix 2: Bibliography 119 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Appendix 2: Bibliography MorphoAccess® terminal bibliography How to get latest version of the documents The last version of the documents below is available on a CD/ROM package from our factory, or downloadable on our web site at the address below: www.biometric-terminals.com (Login and password required). To get your login, please send us a mail to the address below: hotline.biometrics@t.my-technicalsupport.
MorphoAccess® VP Series - User Guide Appendix 2: Bibliography MorphoAccess® Remote Messages Specifications, ref. SSE-0000062580 Details how the MorphoAccess® terminal sends the access control result to a distant system. MorphoAccess® Contactless Card Specification, ref. SSE-0000062610 This document describes the format and the localization on contactless card, of the data required by the authentication modes of the MorphoAccess® terminal. Support Tools MorphoAccess® Configuration Tool User Guide, ref.
MorphoAccess® VP Series - User Guide Appendix 3: Support Appendix 3: Support SSE-0000082427-01 January 2011 MORPHO DOCUMENT.
MorphoAccess® VP Series - User Guide Appendix 3: Support Troubleshooting Terminal IP address is unknown or terminal is not reachable Use USB Network Tool to set a valid network address in your terminal. Refer to USB Network Tool User Guide. Biometric Sensor backlight is off Verify that the base contents at least one record. Check that identification mode is enabled. Terminal returns erratic answers to ping requests Check the subnet mask. Ask your network administrator for the right value.
MorphoAccess® VP Series - User Guide Appendix 3: Support Customer service Repair center Morpho SAV Terminaux Biométriques Boulevard Lénine BP428 76805 Saint Etienne du Rouvray FRANCE Phone: +33 2 35 64 53 52 Hotline and customer assistance Morpho Support Terminaux Biométriques 18, Chaussée Jules César 95520 OSNY FRANCE hotline.biometrics@t.my-technicalsupport.com Phone: + 33 1 58 11 39 19 (9H00am to 6H00pm French Time, Monday to Friday) http://www.biometric-terminals.
Copyright ©2011 Morpho Head office: Le Ponant de Paris 27, rue Leblanc - 75512 PARIS CEDEX 15 – France www.morpho.
Head office: Le Ponant de Paris 27, rue Leblanc - 75512 PARIS CEDEX 15 – France www.morpho.
