Instructions / Assembly

ManualsBrandsIDEAL Security ManualsElectricalAlarm Centre and Telephone Dialer

Rev. 10/05/2012

SK618

WIRELESS ALARM SYSTEM WITH AUTO DIALER

OWNER'S MANUAL

Thank you for choosing Ideal Security’s Home Security System with Telephone Dialer.

If at any time during your installation you have any questions or comments, please do not

hesitate to contact our customer service department through our web site at

www.idealinc.com, via email at info@idealinc.com, or by calling our toll free number at

800-361-2236 x 230. Normal business hours are 7:30am to 3:30pm Eastern time. Monday

to Friday.

You can add up to 23 wireless Ideal Security sensors to this unit, i.e. motion detector,

water detector, door and window contacts, temperature sensor as well as 7 additional

remote controls (for a total of 8 remotes)

Up to date instructions & installation tips can be found at www.idealalert.com

INTRODUCTION

Our unique Auto dialer is designed to allow you to create your own security system. It

will alert you of any intrusion, temperature changes or water leakage (depending on what

sensors you have installed). Choose a desired location for the auto-dialer, set the auto-

dialer to ARM mode. Once a sensor sends signal, the auto-dialer will turn on the built-in

siren (if activated) and dial out (if activated) the pre-programmed telephone numbers one

by one, for the pre-programmed cycles. You can set the auto-dialer to chime mode, you

will hear one chime only when a sensor is activated.

THE TELEPHONE DIALER REQUIRES A LAND TELEPHONE LINE TO MAKE

OUTGOING CALLS AND ELECTRICITY.

Important note regarding:

REGARDING AUTO DIALER, ANSWERING MACHINES &

REMOTE COMMUNICATION.

“REMOTE ACTIVATION” allows user to call into the telephone dialer to perform he

following functions: Activate the system

De-Activate the system

Listen in to the room containing the auto dialer.

ANSWERING MACHINE SETTING AND REMOTE ACTIVATION

If the “REMOTE ACTIVATION” feature is required, the response setting must be

changed to allow for the auto dialer to respond before the answering machine

Summary of content (16 pages)

PAGE 1
Rev. 10/05/2012 SK618 WIRELESS ALARM SYSTEM WITH AUTO DIALER OWNER'S MANUAL Thank you for choosing Ideal Security’s Home Security System with Telephone Dialer. If at any time during your installation you have any questions or comments, please do not hesitate to contact our customer service department through our web site at www.idealinc.com, via email at info@idealinc.com, or by calling our toll free number at 800-361-2236 x 230. Normal business hours are 7:30am to 3:30pm Eastern time. Monday to Friday.
PAGE 2
Rev. 10/05/2012 Depending on your specific needs, priority must be given to either the answering machine or “REMOTE ACTIVATION” If you intend to use the “REMOTE ACTIVATION” features (controlling the alarm unit remotely), you cannot use an answering machine in the usual way. To use the remote activation feature: Set the auto dialer to respond (pick up) before your answering machine responds.
PAGE 3
Rev.
PAGE 4
Rev. 10/05/2012 2. Raise the antenna on the side of the unit so it points up (Fig.3). The antenna should be vertically straight up for better reception. 3. The supplied telephone line splitter can be installed into your telephone wall socket. (Fig.3a) or the LINE Jack of the auto-dialer (Fig.3b) 4. Now using the telephone wire supplied, insert the small clear plug into the LINE jack on the auto-dialer and the other end into the telephone line splitter, (Fig.
PAGE 5
Rev. 10/05/2012 1. TO SET PASSWORD a. Enter factory pre-set password 0-0-0. Press PROG button once (1), PASSWORD will flash on the auto-dialer screen. (Fig.5) button to confirm that you want to enter the b. Press the ARM/DISARM PASSWORD. c. Enter your new password then press the ARM/DISARM button to confirm (you can choose from 3 to 6 digits for your password). d. Record new password here:__________________ e. Press the PROG button nine (9) times to exit set-up mode.
PAGE 6
Rev. 10/05/2012 e. Enter correct year by pressing */UP or #/DOWN button, then press the ARM/DISARM button. The next set of numbers will start flashing, enter the month by pressing */UP or #/DOWN button, then press the button ARM/DISARM , and so on until all numbers have been entered. You will now have the correct date and time. f. Press PROG button once (1) to exit set-up mode. 3.
PAGE 7
Rev. 10/05/2012 5. PAUSE FUNCTION The "PAUSE" function can be stored as one digit in the telephone number memory for some dialing operations. Every one PAUSE in the memory dialing sequence will pause for 3.6 seconds. For example, if you want to store telephone number 514-363-1030 EXTENSION 230 to a memory location, the operation will be as follows: a. Enter password then press PROG button twice (2). b. MEMORY will flash on the auto-dialer screen. c. Press ARM/DISARM button to confirm. d.
PAGE 8
Rev. 10/05/2012 b. The " " icon will flash on the auto-dialer screen. (Fig.8) c. Press ARM/DISARM button to confirm. d. Using */UP or #/DOWN buttons to select call OFF followed by the ARM/DISARM button to confirm. button five (5) times to exit the set-up mode. e. Press PROG 8. TO PROGRAM AUTO DIALLING CYCLE The auto-dialer has been factory pre-set for auto dialing for 3 cycles (When water is detected the auto dialer will call ALL stored numbers 3 times).
PAGE 9
Rev. 10/05/2012 c. Press the ARM/DISARM button to confirm. and #/DOWN buttons select the seconds 0,5,10,15 or 20. d. Using the */UP Press ARM/DISARM to confirm the number of seconds you require for the entry delay time. button twice (2) to exit set-up mode. e. Press the PROG 11. TO TEST MEMORY DIALLING In standby mode, (the word ARM does not appear on the screen) press and hold the PROG button for at least 3 seconds, you will hear a short beep. Key in the memory location of the telephone number, i.e.
PAGE 10
Rev. 10/05/2012 automatically dial all the numbers stored, one by one, for the CYCLE (amount of times the numbers are dialed) you have chosen. The receiver of the phone call will hear one beep cycle for zones 1-7 and 8S, two beep cycles for 24hr zone and four beep cycles for PANIC. The receiver of the call can then call a neighbor, or take other appropriate action. b. In ARM mode, if the auto-dialer is set to SIREN OFF, the numbers stored will be dialed silently.
PAGE 11
Rev. 10/05/2012 Enabling and Disabling sensors when in HOME mode. When in HOME mode all sensors will send signal to auto dialer and you will hear a chime when a sensor is triggered. If you have one or more sensors that you do not wish to have them send a signal to the auto dialer, example a contact on a patio door that is in zone 3, then you would disable zone 3. Zone’s 1-7 can be disabled. All sensors in zone 8S must be enabled or disabled together. They cannot be separated.
PAGE 12
Rev. 10/05/2012 7. REMOTE CONTROL BY TELEPHONE TO CONTROL ALARM (To control your auto dialer via telephone) (see ANSWERING MACHINES and REMOTE COMMUNICATION) a. Dial your home number (from anoher line). The auto-dialer will answer after the designated amount of rings that you have programmed. b. Once answered enter your PASSWORD, you will hear two beeps (confirmation). c. Enter key combination listed below for desired function you would like to perform.
PAGE 13
Rev. 10/05/2012 View Triggered Events If alarm has been triggered it will flash on the LED screen. To view, in standby mode, press #/DOWN button to view the last 5 triggered Events. Once viewed, TRIGGER will disappear from the screen. View stored telephone numbers In standby mode, press */UP to view stored telephone numbers. NOTE: If no buttons are pressed for 10 seconds, the auto-dialer will automatically exit view mode. TO LEARN ADDITIONAL WIRELESS SENSORS OR REMOTE CONTROL CODES.
PAGE 14
Rev. 10/05/2012 e. Press ARM/DISARM to confirm that this is the zone you want the sensor to be. f. Trigger the sensor or remote control that you are trying to learn as follows: 1. Wireless motion detector SK615, by moving hand in front of sensor to send signal.* please see NOTE below 2. Wireless door/window sensor SK621 & SK625, opening and closing the magnetic switch will send signal. 3. Wireless water alarm sensor SK616, put sensor in water to trigger and send signal. 4.
PAGE 15
Rev. 10/05/2012 3. Once learn code was successful you must turn ON the AC Outlet Control in order to receive the signal from the auto-dialer. NOTE: You will hear a long beep to confirm that the learn code was successful. When learn code is not successful you will hear 4 short beeps. If this happens please re-learn again. TROUBLE SHOOTING GUIDE 1. AUTO-DIALER WILL NOT ARM/DISARM a. Make sure you have entered the correct password, if not, re-enter the password. b.
PAGE 16
Rev. 10/05/2012 All batteries including the back up battery in the telephone dialer should be changed once per year. Should a power failure occur and the back up battery is weak, or batteries in all your sensors are weak, false alarms may occur. If the telephone dialer or any other detector is not being used for an extended period, remove the batteries to avoid any damage due to battery leakage. NOTE: Please preserve this manual.