ID-TECK PROXIMITY READER STAR RFK101 INSTRUCTION Proximity Reader with KEYPAD ID TECK Co. Ltd.
ID-TECK PROXIMITY READER STAR RFK101 CONTENTS 1. Introduction page 3 2. Identifying supplied parts page 3 3. Specification page 3 4. Installation page 4 5. Wire Color Table of the Reader page 5 6. Wire Connection to Controller page 6 7. Operation page 7 8. Output Format page 9 9. FCC Registration Information page 13 10.
ID-TECK PROXIMITY READER STAR RFK101 1. Introduction The STAR RFK101 is an elegant looking and built in an attractive 4" read range proximity reader with KEYPAD. The RFK101 has back lighting on the KEYPAD that ensure you successful operation even the night operating. The KEYPAD allows you to access door with proximity card and personal PIN numbers. Three LEDs of green, yellow and red, inside Piezo buzzer sound will guarantee you an accurate and reliable system operations. 2.
ID-TECK PROXIMITY READER STAR RFK101 Color Operating Environment Dark Pearl Gray -35℃ ~ +65℃, 10~90% Humidity Overall Size(WxHxD) Weight Output Format 3.40"x3.94"x1.22"(487x100x31mm) 0.412 lbs(190 g) 26bit Wiegand, RS-232, ABA Track II Magstripe Output Format with 8bit Burst or 3x4 Matrix Format for PIN 4. Installation 4-1. Drill two 6-32 or M3 holes 3.3"(8.38cm) apart in vertical and one 1/2" hole at the center of these two holes. (If you have installed electric gang box then skip this step.) 4-2.
ID-TECK PROXIMITY READER STAR RFK101 5.
ID-TECK PROXIMITY READER STAR RFK101 6. Wire Connection to Controller 6-1. 26bit Weigand+RS232(for Card) and 8bit Burst format(for PIN) . The Reader transmits Card data to Wiegand Data0,Data1 and RS-232 TX line. . The Reader transmits PIN data to Wiegand Data0 and Data1.(8bit Burst format.) 6-2. ABA Track II+RS232(for Card) and ABA Track II+RS232(for PIN) . The Reader transmits Card and PIN data to Card present, Clock, DATA and RS-232 TX line. NOTE : You have to enter at least 1 numeric number(max.
ID-TECK PROXIMITY READER STAR RFK101 7. Operation 7-1. Connector Layout 7-2. Output mode Setting Table 1.
ID-TECK PROXIMITY READER STAR RFK101 7-3. Operation 1. Once the power is applied, you should hear 3 times of initial beep sounds and red A nd yellow L E Ds on indicating that the reader is in standby mode after a successful initialization and diagnostics. 2. Present proximity card to the reader until you hear the beeping sound and the green LED on. The reader will send the RF card data to the controller then the yellow LED on again for the next reading. 3.
ID-TECK PROXIMITY READER STAR RFK101 8. Output Format 8-1. 26bit Wiegand output format 1. Data format Bit 1 Bit 2~9 Bit 10~25 Bit 26 : Even parity of bit 2 ~ bit 13 : Facility code (000 ~ 255) : ID number (00000 ~ 65,535) : Odd parity of bit 14 ~ bit 25 2. Timing diagram 8-2. ABA Track II Magstripe output format 1.
ID-TECK PROXIMITY READER STAR RFK101 2. Data format(for PIN) 3.
ID-TECK PROXIMITY READER STAR RFK101 8-3. 8bit Burst output format(for PIN) 1. Data format 2.
ID-TECK PROXIMITY READER STAR RFK101 8-4. RS-232 output format 1. Data format(Baud rate : 9600bps) LSB MSB +15V 0 1 0 0 0 0 0 1 0 Space (=0) +3V Indeterminate Region 0V -3V Mark (=1) 8 Data Bits -15V 2 Stop Bits Start Bit Data packet corresponding to ASCII character 'A' 2. Data structure START(0X02H) DATA(8 Char) END(0x03H) LRC (CARD output) START(0X02H) DATA(1~8 Char) END(0x03H) LRC (Keypad output) 8-5. Matrix(3x4) format 1.
ID-TECK PROXIMITY READER STAR RFK101 9. FCC REGISTRATION INFORMATION FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference, and 2.
ID-TECK PROXIMITY READER STAR RFK101 10. Warranty and Service The following warranty and service information applies only to the United States of America and Republic of Korea. For the information in other countries, please contact your local distributor. To obtain in or out of warranty service, please prepay shipment and return the unit to the service facility listed below. IN THE UNITED STATES RF LOGICS Inc. Service Center 3026 Scott Blvd., SANTA CLARA, CA95054 Tel.: (408) 980-0001 Fax.