MODEL : STAR100R ACCESS CONTROLLER OWNER’S MANUAL Please read this instruction manual carefully
Contents 1. Important safety instructions 2. General 3. Features 4. Specification 5. Connection 6. Wire color table 7. Operation 8. FCC Registration information 9.
-21. IMPORTANT SAFETY INSTRUCTIONS When using your door access controller, basing safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons including following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product 3. Do not use liquid cleaners, or aerosol cleaners. Use a damp cloth for cleaning. if necessary, use a mild soap. 4.
-3 2. General STAR100R is an intelligent one door Access Controller based on powerful 8 bit Microprocessor to meet a simple and cost-effective access control market requirement. User friendly device allows you to register max. 127 USER RFID and easy to add or delete USER RFID. Built in Proximity reader gives you 2 different operating mode such as RF ONLY MODE or RF+PASSWORD MODE.
-44. Specification .CPU .Memory : 8 bit Microprocessor : 8 KB Program memory 512 bytes Flash memory .User RFID numbers : 128 User RFID including one Master RFID .Proximity Reader : 125KHz PSK reader, 4 inch reading range .Input/Output : 5 Inputs and 4 Outputs including 2 Relays .Communication : One RS232C port, 9600 Baud Rate .Keypads : 12 Numeric Keypads .LED : 3 LEDs(RED, GREEN, YELLOW) .Power : DC 12V, 250mA .Operating Environment : 0°C to +60°C, 10% to 90% Humidity .Reset : Power ON Reset 5.
-56.
-67. Operation 7.1 INITIAL SETTINGS: STAR100R HAS COMPLETELY BLANK WHEN IT IS DELIVERED TO CUSTOMER. THE UNIT AUTOMATICALLY ENTERS TO INITIAL SETTING MODE WHEN IT IS POWERED ON. (YOU MAY ALSO ERASE ALL MEMORY BY CLOSING A JUMPER ON "JP3" OF MAIN P.C.BOARD) PROGRAMMING SEQUENCE IS AS FOLLOWS; - Connect 12V DC Power supply to RED(+) and BLACK(-) cable. - Power switch on. (RED LED will lit and YELLOW LED is blinking every seconds). - Press the keypads as follow.
-7THE DEFAULT SETTINGS ARE; - When User RFID Granted: Output RELAY#1 activates for 3 seconds Green LED activates for 3 seconds - Exit Input entered: Output RELAY#1 activates for 3 seconds Green LED activates for 3 seconds - When User RFID denied:(within Try-out count, default 5 times) Output RELAY#2 activates for 1 second - When Try-out error occures:(from 6th Try-out) Output RELAY2 activates for 5 second - Numbers of Try-out counter set to 5 times - Keypad input limit time set for 10 seconds - Silent opera
-87.
- OUTPUT TEST when INPUT#3 ENTERED: (Master RFID)+(37)+(ENT) -9- SILENT MODE SET: (Master RFID)+(51)+(ENT) - SILENT MODE RESET: (Master RFID)+(52)+(ENT) - CONTACT TIME SET: (Master RFID)+(81)+(ENT)+(time)+(ENT) time = 00~99 (second) - TRY-OUT COUNT SET: (Master RFID)+(82)+(ENT)+(number)+(ENT) number = 00~99 (times) - KEYPAD INPUT LIMIT TIME SET: (Master RFID)+(83)+(ENT)+(time)+(ENT) time = 00~99 (second) - ALARM PORT SET: (Master RFID)+(84)+(ENT)+(port)+(ENT) port = 01~16 (port No.
- 10 7.4 OUTPUT CONFIGURATION CHANGE - OUTPUT CONFIGURATION CHANGE when User ID is granted (Master RFID)+(21)+(ENT)+(oo)+(ENT) +(t1)+(ENT)+(t2)+(ENT)+(t3)+(ENT)+(t4)+(ENT)+(t5)+(ENT) oo = Output numbers t1 = OUTPUT RELAY#1 activate time t2 = OUTPUT RELAY#2 activate time t3 = TTL OUTPUT activate time t4 = GREEN LED activate time t5 = BUZZER activate time Note: Output numbers(add all numbers below which you want to activate) 1 ...activate OUTPUT RELAY#1 2 ...activate OUTPUT RELAY#2 4 ...
EX) If you put "05" for t2 then OUTPUT RELAY#2 will activates for 5 seconds. - 11 - OUTPUT CONFIGURATION CHANGE when TRY-OUT ERROR occurs (Master RFID)+(23)+(ENT)+(oo)+(ENT) +(t1)+(ENT)+(t2)+(ENT)+(t3)+(ENT)+(t4)+(ENT)+(t5)+(ENT) EX) If you want OUTPUT RELAY#2 and TTL Output activate in SECURE MODE then 2+4=06 as output numbers and you put "06" for (oo) format. Activate time for t1 through t4 is "00" to "99" seconds.
- 12 - FCC REGISTRATION INFORMATION FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance cold void the user's authority to operate the equipment. NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
- 13 - WARRANTY AND SERVICE The following warranty and service information applies only to the U.S. For information in other countries, please contact your local distributor. To obtain in or out of warranty service, please prepay shipment and return the unit to the appropriate facility listed below. IN THE UNITED STATES RF LOGICS, INC. Service center 3026 SCOTT BLVD, SANTA CLARA, CA 95054 Tel. : (408) 980-0001 Fax.: (408) 980-8060 Email: webmaster@rflogics.com Website : www.rflogics.
- 14 -
