User Manual PROX10/10H Proximity Reader
User Manual Table of Contents 1. SAFETY INFORMATION ......................................................................3 2. PRODUCT INTRODUCTION.................................................................. 5 3. IDENTIFYING SUPPLIED PARTS ............................................................5 4. PRODUCT SPECIFICATION .................................................................. 6 5. PRODUCT INSTALLATION ................................................................... 7 6.
User Manual 1. SAFETY INFORMATION This caution is for safety and preventing damage of property Please read these instructions and follow them. 1) Acquaint yourself with all instructions thoroughly. 2) Heed all warnings and follow the instruction on the product. Keep the instruction in a conspicuous place so administrator can see it always. Power Supply must be DC 12V. - Higher voltage might cause electric shock, fire and damage on the product. Do not install the unit in humid, dusty, or sooty locations.
User Manual When cleaning, do not spray water directly onto parts of the product nor benzene, thinner. - Doing so may cause fire or electric shock or damage on the unit. Operation and maintenance Do not randomly change the wiring installed by engineer or expert. - Doing so may cause fire or malfunction or damage of the unit. Do not let the unit be touched by person expect administrator for unusual purpose of using.
User Manual 2. PRODUCT INTRODUCTION PROX10 / PROX10H have sophisticated design as well as maximum recognition distance of 4 inch. This proximity reader can be easily attached to a metal or doorframe or the wall. Featured by the epoxy adhesion, PROX10 /PROX10H have high level of weather-proofing in any challenging weather conditions. This model contains red and blue inside and Piezo buzzer guarantees accurate and reliable system operation. 3.
User Manual 4. PRODUCT SPECIFICATION Recognition distance /time 4"(10cm) / 30ms Power/Current DC 12V, Max. 150mA Output 26 bit Wiegand, 34bit Wiegand, RS232C External buzzer control input Low Active, DC 0 ~ 12V, Max. 50 mA External LED control input Low Active Low Active, DC 0 ~ 12V, Max. 50 mA LED/buzzer 2 Color LED(Red/Blue) / Piezo Buzzer Color Dark Pearl Gray 14℉ ~ 140℉(-10℃ ~ +60℃), Operating temperature/humidity 10~90%(Humidity) 1.92" x 4.33" x 0.85"(49x110x21.
User Manual 5. PRODUCT INSTALLATION 5-1. Inserting into doorframe / Attaching to wall The distance between two 6-32/M3 holes which are located vertically is 3.3"(8.38cm). One 1/2" hole between them is for cable from the reader and has 1.7"(4.31cm) of distance from upper hole. (If it has been attached already, you can skip this part) 5-2. Insert the reader cable to the hole in the middle and fix reader module with two 6-32/M3 screws. 5-3. put the reader module in Bezel and push it until it clicked shut.
User Manual 6. WIRE COLOR TABLE Signal COLOR Main Power (+12V) Red Power Ground (GND) Black Wiegand Data 0 Out Green Wiegand Data 1 Out White Buzzer Control In Blue LED Control In Yellow RS232C (TX) Brown * Please cut out tail connector before installation. 7.
User Manual 8. OPERATIONS 8-1. When power is applied to the reader, buzzer that indicates initialization is generated. And the Blue LED is lit once the initialization is completed. And the reader becomes standby mode. 8-2. Put the card near the reader until LED light changes from blue to red and buzzer is generated. Reader sends the data to controller and becomes standby mode for following card reading. 8-3. LED Control Color of LED can be changed by connecting LED control input(Yellow wire) to GND.
User Manual 9. FCC REGISTRATION INFORMATION FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interface, and 2.
User Manual 10. PRODUCT MANUAL DOWNLOAD INFORMATION This Quick Installation Guide is a manual to provide product’s basic installation information only. If you need all the information of the product, please download detailed manual following the steps specified below. For registered users of our homepage 1. Visit IDTECK’s homepage (www.idteck.com). 2. Click the Sign in button at the top of the homepage and log in using your registered ID and P/W. 3.
User Manual MEMO 12
User Manual The specifications contained in this manual are subject to change without notice at any time. 5F, Ace Techno Tower B/D, 468, Gangseo-ro, Gangseo-Gu, Seoul, 157-030, Korea Tel : +82-2-2659-0055 Fax : +82-2-2659-0086 E-mail : webmaster@idteck.com Sep. 2014 Copyright ©2014 IDTECK Co., Ltd.