User’s Manual LX006 Fingerprint Identification Proximity Reader
TABLE OF CONTENTS 1. IMPORTANT SAFETY INSTRUCTIONS .......................................................................................................................... 4 2. FEATURES ....................................................................................................................................................................... 5 3. SPECIFICATION .........................................................................................................................................
9.1 INITIALIZATION OF LX006 ................................................................................................................................. 25 9.2 COMMUNICATION ID SETTING ......................................................................................................................... 25 10. OPERATION MODE ..................................................................................................................................................... 26 10.
1. IMPORTANT SAFETY INSTRUCTIONS The description below is to keep user’s safety and prevent any product damage. Please fully read these instruction and use the product properly. Danger: This symbol indicates that incorrect handling of the product may result in serious injury or death. Warning: This symbol indicates that incorrect handling of the product may result in injury or property damage. Cautions about power - Only use the standard voltage (DC +12V/ 350mA).
2. FEATURES Fingerprint Recognition Proximity Reader The LX006 is a Fingerprint and Proximity Reader compatible with existing proximity readers. The LX006 has a built-in proximity reader and fingerprint module so that the access is only allowed when the personal ID and fingerprint are authorized and this integrated system gives you high and reliable security. The LX006 can register up to 200,000 User IDs and 1,000(default)/ 2,000(optional) / 4,000(optional) fingerprint users.
Card Number Output Format When a fingerprint is authorized, the corresponding card number is transmitted to the controller via 26/34Bit (SR) Wiegand or ABA Track II according to the output type setting. It is set by application software. Card Number Input Format The LX006 receives the card number from the external reader while the LX006 contains a built-in proximity reader inside. The LX006 receives the card number in 8bit Burst or 26bit Wiegand or ABA Track II format.
3.
Read Range Model Read Range IDC80 IDC170 Maximum of 4 inches LX006 (10cm) Fingerprint Module Specification Resolution 500dpi Capture Image Size 356 X 292 pixels Extraction Image Size 248 X 292 pixels Sensing Area 12.7 X 14.9mm Scanner High Quality Optical Sensor FAR(False Acceptance Ratio) 0.001% FRR(False Reject Ratio) 0.1% ESD(Electro Static Discharge) ±8KV Verification Time Less than 1sec. Identification Time Less than 2sec.
4. IDENTIFYNG SUPPLIED PARTS Please unpack and check the contents of the box. If any of flowing items is missing, please contact nearby contributor. (Optional accessories, if purchased, may be included in the package.) LX006 (1 ea) User’s Manual (1 Copy) Wall Mount (1 ea) Screw 3 X 30 mm – 2 ea 3 X 6 mm – 1 ea 3.
5. PRODUCT EXPLANATION 5.1 PANEL LAYOUT Status LED Fingerprint Scanner Proximity Reader Speaker (Figure: Panel Codes) 5.
5.
6. INSTALLATION TIPS & CHECK POINTS Please refer to information below to stably operate the LX006. 6.1 CHECK POINTS BEFORE INSTALLATION 6.1.1 CABLE SELECTION POWER POWER (Figure: System configuration) 6.1.2 RECOMMENDED CABLE TYPE AND PERMISSIBLE LENGTH OF CABLE No Cable specification Description 1 LX006 Power (DC+12V) DC Power -> LX006 *2 RS232 Cable converter->Host P.C.
The most of ACU is capturing the signal by the voltage level of data input. 1V is the critical point whether the ACU read the data logic “1” or logic “0” therefore the reader output cannot be read correctly from the ACU. There will be two methods to reduce the voltage drop and ACU can read data correctly. Reduce the DC resistance of GND wire; Using thick cable or add more wires to GND wire in parallel.
6.2.2 HOW TO CONNECT TERMINATION RESISTORS (Figure: Termination resistors for 2 wire RS485 communication system) 6.2.3 GROUNDING SYSTEM FOR COMMUNICATION CABLE We recommend proper grounding system on the communication cable. The best method for grounding system is to put the shield wire of the communication cable to the 1 st class earth grounding; however it is not so easy to bring the earth ground to the communication cable and also the installation cost is raised.
7. INSTALLATION OF THE PRODUCT 7.1 WALL MOUNT DRAWING (Unit: mm) (Figure: Wall Mount) 7.2 INSTALLATION OF WALL MOUNT - Place the Wall Mount on the desired position on the wall and mark the locations of the 2 screw holes. - Drill a hole in the center of the Wall Mount for cable. - Take out the cable from the center of hole. - Wire cable to four connecters and then perform initialization and set communication ID. - By using of one screw on the bottom, fix the Wall Mount with LX006.
7.3 SYSTEM INITIALIZATION Initialize the system using the DIP switch on the rear of the product. 1. Disconnect the power supply. 2. Position the DIP switch on the rear of the product to ON (upside) and apply power to the product. 3. The product sounds a beep once with a voice message, and proceed with the hardware initialization process. 4. When the initialization is done, the product sounds a beep three times with a completion message output.
7.4 COMMUNICATION ID SETTING LX006 can upload/ download user’s information by application software and adjust setting values. Communication ID is the unique communication address to recognize each LX006 in the software so each communication ID on the same communication loop must not be duplicated. There is 8-bit DIP switch on the back of LX006 for communication ID setting and each channel of DIP switch has assigned address values.
7.5 WIRING 7.5.1 WIRING LAYOUT Controller Buzzer Control LED Control System Mode Control Wiegand White with Red stripe Blue with White stripe Gray with Red stripe ABA Track II Orange with Black stripe Authentication input Authentication error input DATA1 DATA0 DC12V GND(-) TAMPER RS485-A(+) RS485-B(-) Orange White Green CLS CLK DATA Red Black Purple Pink Yellow Gray Cyan RJ45 8bit Burst 26bit/34bit(SR) HUB Wiegand DATA1 DATA0 DC +12V GND(-) External reader 7.5.2 Power Wiring 1.
7.5.3 INPUT WIRING External LED Control Connection Connect the LED Control Input wire (Blue wire with White stripe) to the NO port of controller relay output, and GND to the COM port. Set I/O of the controller; then you can control tuning on and off the green LED. While the LED control is working, the green LED stays on. The controller can use the I/O setting to set the LED controller so that it displays the additional LED status for authorized/unauthorized access.
7.5.4 OUTPUT CONNECTION Wiegand DATA Output Connection 1. Connect Wiegand Data 0 wire (Green wire) to Wiegand Data 0 terminal of the Controller. (Used for DATA when ABA Track II is output) 2. Connect Wiegand Data 1 wire (White wire) to Wiegand Data 1 terminal of the Controller. (Used for CLOCK when ABA Track II is output) 3. The GND(-) wire must be connected between the LX006 and the Controller.
7.5.5 EXTERNAL READER CONNECTION Proximity Reader Connection 1. Connect the DC+12V wire of Power Supply to (+) wire of reader. 2. Connect the GND(-) of Power Supply to (-) wire of reader 3. Connect the Wiegand Data 0 wire of the External Reader to the Wiegand Input Data 0 wire of LX006 (Pink wire). 4. Connect the Wiegand Data 1 wire of the External Reader to the Wiegand Input Data 1 wire of LX006 (Cyan wire). 5. The GND(-) wire must be connected between the external and the LX006.
8. COMMUNICATION 8.1 RS485 COMMUNICATION PORT CONNECTION 8.1.1 RS485 COMMUNICATION PORT CONNECTION (SINGLE CONNECTION) An RS-485/RS-232 converter is required to connect serial communication RS485 between the LX006 Main Unit and the Host Computer. - Connect RS485 - RTX (+) (Yellow) wire of Main Unit to RS485-A of Converter. - Connect RS485 - RTX (-) (Gray) wire of Main Unit to RS485-B of Converter. - Plug the RS232 9-pin connector of INC300 converter into COM1 or COM2 Port of Computer.
8.1.2 RS485 COMMUNICATION PORT CONNECTION (MULTIPLE CONNECTION) RS485/RS232 converter is required to use RS485 communication between multiple LX006s and a host computer. Please follow the following instructions. First, you have to connect all RS485 port of all LX006s in parallel. (Maximum of 255) - Connect RS485-A(+) (Yellow) of one LX006 to RS485–A(+) (Yellow) of another LX006. - Connect RS485-B(-) (Gray) of one LX006 to RS485–B(-) (Gray) of another LX006. - Set different COMM ID for each LX006.
8.2 TCP/IP COMMUNICATION PORT CONNECTION For TCP/IP communication, external cable is required to connect to CON4 (8PIN connecter). Please follow the following instructions. 1. Connect the LAN cable of the network system to the RJ45 jack of the LX006. 2. Install and run the Application Software.
9. BASIC SETTING 9.1 INITIALIZATION OF LX006 - Initialization should be performed before mounting the LX006 to the Wall Mount. - If you need to initialize LX006 after installing it on the wall, you can use the Application Software to do that. (Refer to the Software Manual for more information.) - For more information about how to initialize the LX006, refer to ‘7.3 SYSTEM INITIALIZATION’.
10. OPERATION MODE 10.1 MASTER CARD REGISTRATION MODE While the LX006 is operating in the Master Card Registration Mode, the Red and Green LEDs are lit. 10.1.1 MASTER CARD REGISTRATION The card presented to the LX006 for the first time after initialization becomes the master card. ※ NOTE: Fingerprint verification is not used for the Master Card. After the Master Card is recognized, the Green LED blinks with 3 beeps. 10.1.
2. Yellow and Green LED indicators blink. 3. Present the Proximity Card you want to delete to the LX006. 4-1. RF + FINGER MODE: After presenting the user card you want to register, you should enter the desired fingerprint twice. Follow the steps below to register a new user card; - Present the proximity card to the LX006. - Place the fingerprint on the fingerprint scanner while red light is illuminated from it - Lift the fingerprint up when the red light from the scanner turns off.
10.2.3 USER CARD DELETION To delete registered user cards, follow steps below; 1. Present the Master Card to the LX006. 2. Yellow and Green LED indicators blink. 3. Present the Proximity Card you want to delete to the LX006. 4. After the deletion is successfully completed, you’ll hear 4 beeps. If the deletion is not successful, you’ll hear 2 beeps. 5. If you want to delete more user cards, repeat the steps above. 6.
error signal is not generated when using ABA Track II format.) If the card hasn’t yet been registered, 1. The buzzer generates 2 short beeps and the Yellow LED blinks twice to indicate that the presented card is unregistered or deleted. 2. When an unregistered card is presented or a fingerprint is not verified, an Access Error Signal output (Low Active) will be generated for 500ms. (The error signal is not generated when using ABA Track II format.) 10.
10.5 DEFAULT SETTINGS The initialization before installation restores the default values (factory settings) of the LX006. For desired applications, you may adjust or customize the settings via the Application Software. The default values for the basic settings are as follows; 1. Operating Mode: RF + FINGER 2. Fingerprint Registration: 1 ID 1 Finger Two Template 3. Output Format: 26bit Wiegand/34bit Wiegand(SR) 4. Input Format: 26bit Wiegand/34bit Wiegand(SR) 5. Output Mode: Normal Mode 6.
11. OUTPUT FORMAT 11.1 WIEGAND OUTPUT (DEFAULT) Data format (26-bit) Bit 1 / Bit 1: From Bit 2 to Bit 13 / From even parity Bit 2 to Bit 17 Bit 2 to Bit25 / Bit 2 to Bit33: 3-byte ID number / 4-byte ID number Bit 26 / Bit 34: From Bit 14 to Bit 25 / From odd parity Bit18 to Bit 33 Output Timing 11.
Output timing CP CLK Data 1240us 940us (RD1) 6000us 1544us (RD0) 11.3 OUTPUT MODE 11.3.
11.3.2 EXTENSION OUTPUT MODE (SET BY APPLICATION SOFTWARE) User ID / Fingerprint authorized User ID unregistered/ Fingerprint error 12. APPENDIX A. Trouble Shooting ☞ Unable to enter the registration mode with master card Cause Of master card registration error or of setup error 1. Check a master card. Cause Try changing a master card and enter the registration mode with changed card. 2. Initialize the unit referring to user’s manual.
1. Check the fingerprint position on the scanner. . 위치가 지문들 Wrong잘못된 position 정상적인 지문 Correct position 2. Check condition of the fingerprint. Cause Normal Dry Wet Low pressure High pressure 3. ADAPTIVE MODE is to compensate too dry and wet fingerprint. When ADAPTIVE MODE is applied, the fingerprint capture time takes longer but the performance of fingerprint recognition will be higher. You can apply ADAPTIVE MODE using application software. ☞ The controller does not communicate with Host PC.
2. Check the line connection for communication. In case of RS485 RS485 (mono) LX006 RS485/232 Converter RS485-A(+) RS485-A(+) RS485-B(-) RS485-B(-) PC RS232 Cable of connecter RS485(Multi Drop) LX006 LX006 RS485/232 Converter RS485-A(+) RS485-A(+) RS485-A(+) RS485-B(-) RS485-B(-) RS485-B(-) PC RS232 Cable of connecter - When a multi-drop communication doesn’t work, test one-by-one Communication from first.
B. How to register fingerprint Correct Fingerprint Registration Method Correct Method Scanning Fingerprint Successful Verification / Identification Scanning Fingerprint Fail Verification / Identification Incorrect Method In case of not a fingerprint registration Wet Fingerprint Dry Fingerprint Scarred Fingerprint Injured Fingerprint Dry Wet Scarred Management Method If Fingerprint is excellently recognized...
13. FCC REGISTRATION INFORMATION FCC Requirements Part 15 CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interface, and 2.
14. WARRANTY POLICY AND LIMITATION OF LIABILITY IDTECK warrants this product against defects in material and workmanship for the period specified below from the date of purchase under normal customer use.
15. HOW TO MAKE RMA REQUEST (AFTER SALES SERVICE) To make the RMA request, the product must be initially registered on IDTECK webpage. After registering the product, please send it to IDTECK RMA Center. Please follow the instructions below: 1. Please register the RMA request via IDTECK webpage. : www.idteck.com “Support & Download” “Online RMA” “RMA REQUEST” (Please refer to the IDTECK webpage for more details.) 2. RMA Code will be issued after the RMA Center reviews the RMA request form. 3.
The specifications contained in this manual are subject to change without notice. 5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul, 157-030, Korea Tel : +82-2-2659-0055 Fax : +82-2-2659-0086 E-mail : webmaster@idteck.com Copyright © IDTECK Co., Ltd.
