User’s Manual 2.
Table of Contents 1. Important Safety Instructions....................................3 2. General ........................................................................3 3. Features.......................................................................4 4. Specification ...............................................................4 5. Identifying Supplied Parts .........................................4 6. Installation...................................................................5 7.
1. Important Safety Instructions When using RF245, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons. In addition, the following safety guides should also be followed: 1. Fully read and understand all instructions and follow them completely. 2. Follow all warnings and instructions marked on the product. 3. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. If necessary, use mild soap. 4.
3. Features - Long Range Reader (5~10m with IDA245) - 2.402GHz Frequency, 125 channel - Encrypted Tag ID and Secure Protocols between Reader and Tags - Multiple Tags Reading (30 Tags / Sec) - 90° One Directional Antenna - 26bit Wiegand and RS232 Output Format - Direct Bargate Output (Open Collector: 100mA/1s) 4.
6.
Reading Angle of RF245 The reading angle of RF245 is approximately 90 degree at the front side of the reader. However the reader has about 10% of the maximum reading distance at the rear side of the reader.
. Wire Color Table SIGNAL COLOR Main Power (+12V) Red Power Ground (GND) Black Wiegand Data-0 Output Green Wiegand Data-1 Output White Buzzer Control Input Blue OTR1) Control Input Yellow Bargate2) Output Gray RS232 (TX) Purple OTR1) is One Time Reading. Bargate2) is an open collector output. (TR Output) Max.100mA current drain, about 1s low active pulse. 8. Output Format 8-1. 26bit Wiegand Output Timing Data bit: 100us low active pulse Interval between bits: 1ms 8-2.
9. Wire Connection to Access Controller Access Controller Main Power (+12V) Power Ground (GND) Wiegand Data 0 Output Wiegand Data1 Output Buzzer Control Input OTR1) Control Input Bargate2) Output RS232 (TX) Red Black Green White Blue Yellow Gray Purple 10. Operation 10-1. Apply the power to the reader. The RF245 reader will setup receiving channel and Site Code automatically. Then the Reader will get into standby mode after a successful initialization and diagnostics. 10-2.
11. FCC Registration Information FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interface, and 2.
12. Warranty and Service The following warranty and service information applies only to the United States of America and Republic of Korea. For the information in other countries, please contact your local distributor. To obtain in or out of warranty service, please prepay shipment and return the unit to the service facility listed below. Headquarters: IDTECK Co., Ltd.
13. Frequently Asked Questions Q: Why the RF245 Reader can not read some tags ? A: The RF245 Reader has a Site Code programmed when it powered up and the Reader only reads the tag has same Site Code. To change the Site Code of the Reader, power off for 5 seconds and power on again then try to read a tag. The Reader will re-program the Site Code sending from the tag.
The contents of this manual is subject to change without notice at any time. IDTECK CO. LTD. 5F. Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul 157-030, KOREA Tel.: +82 2 2659 0055 Fax.: +82 2 2659 0086 Website: www.idteck.com E-mail : webmaster@idteck.com MARF245HE10 August. 2006 Copyright ©2006 IDTECK Co., Ltd.