CR IMMO User Manuall Copyright Information Copyright © 2021 by Icarsoft Technology Inc. (also called iCarsoft for short). All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying and recording or otherwise, without the prior written permission. Statement: iCarsoft owns the complete intellectual property rights for the software used by this product.
CR IMMO User Manuall Wear an ANSI-approved eye shield when testing or repairing vehicles. Put blocks in front of the drive wheels and never leave the vehicle unattended while testing. Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltage when the engine is running.
CR IMMO User Manual Table of Contents 1 Packing List.................................................................................................. 1 2 Overview........................................................................................................ 2 2.1 Introduction.........................................................................................2 2.2 Display Tablet.....................................................................................3 2.3 VCI Dongle..............
CR IMMO User Manual 1 Packing List The following accessory items are only for reference. Please consult from the local agency or check the package list supplied with this tool together. No. Item Descriptions Qt. 1 CR IMMO Main Unit 1 2 VCI VCI dongle 1 3 IM2000 PRO Immobilizer Programmer 1 4 OBD II extension cable Connects the VCI dongle to the OBD II vehicle’s DLC. 1 5 USB cable 6 Power adaptor For charging the tablet.
CR IMMO User Manual 17 INS Cable V1 18 INS Cable V2 19 MCU Cable V1 20 21 Connect the programmer and vehicle dashboard, and then place the probe (the yellow lead) to the designated area. After removing the vehicle dashboard, connect programmer, vehicle dashboard, and the cable. To connect the programmer and MCU. Connect the programmer and the engine to read engine or gearbox ECU (Connect engine ECU with Bench Mode Cable the BENCH mode cable based on BENCH mode diagram).
CR IMMO User Manual 2.2 Display Tablet 1. Docking slot for VCI dongle - for housing the VCI dongle. 2. VCI dongle - It is pre-installed in the docking slot on the top of the display tablet. Use the hand to press the dongle once, it will be automatically ejected from the docking slot. When it is not in use, please reinsert it into the slot to avoid loss. 3. Power key - Press it to turn the tool on/off. 4. LCD Screen – Indicates the test results. 5.
CR IMMO User Manual Technical Parameters • • • • • • • • • • CPU: 4-Core 1.8GHz Memory: 4GB ROM: 64GB Screen Size: 8 inches Resolution: 1280*800 pixel Camera: 8MP rear-facing camera Working Voltage: 5V Working Current: 3A Working Environment: 0 ~45 Storage Environment: -10 ~60 2.3 VCI Dongle This dongle works as a VCI (Vehicle Communication Interface) device. It is used to obtain the vehicle data, and then send it to the tablet for analysis via Bluetooth. 1.
CR IMMO User Manual 2.4 IM2000 PRO The IM2000 PRO works as a dedicated anti-theft immobilizer programmer. It needs to work with the display tablet to perform the IMMO Matching (for some vehicles) and IMMO Programming operations. 1. DB26 diagnostic connector - Connects with the Mercedes Benz infrared collector, ECU cable and MCU cable etc. 2. Mercedes Benz infrared key slot - Holds the Mercedes Benz key. 3. Vehicle key slot - Holds the car key for RF defection. 4.
CR IMMO User Manual 3 Initial Use 3.1 Charging Follow the steps below to charge the tablet: 1. Connect one end of the charging cable to the USB socket of the power adapter. 2. Connect the other end to the charging port on the bottom of the host. 3. Plug the charger power plug into a power outlet to start charging. Caution: Please use the included power adaptor to charge your tool. No responsibility can be assumed for any damage or loss caused as a result of using power adaptors other than the one supplied.
CR IMMO User Manual 3.5 Network Setup The tablet has a built-in Wi-Fi communication module. Once you’re online, you can register your tool, update diagnostic software & APK, browse the Internet and send email on your network. 1. In the Job Menu, tap Settings -> Network & Internet -> Wi-Fi. 2. Slide the Wi-Fi switch to ON, the tablet starts searching for available wireless LANs. 3. Select the desired WLAN network from the list. If the chosen network is open, you can connect directly.
CR IMMO User Manual 3. Download diagnostic software: Tap OK to enter the update center to download all available software. B. If you have registered to be a member, input your name and password, and then tap Login to enter the main menu screen directly. Note: The tablet has an auto-save function. Once the username and password are correctly entered, the system will automatically store them. Next time you login the system, you will not be asked to input the account manually. C.
CR IMMO User Manual • Find DLC location. The DLC (Data Link Connector or Diagnostic Link Connector) is usually located 12 inches from the center of the instrument panel, under or around the driver’s side for most vehicles. For some vehicles with special designs, the DLC location may vary. If the DLC cannot be found, refer to the vehicle’s service manual for the location. 4.2.2 Vehicle Connection Follow the steps mentioned below to connect OBD II vehicle: 1. Locate the vehicle’s DLC socket. 2.
CR IMMO User Manual 5 Immobilizer Operations 5.1 Anti-theft matching This function enables you to perform the anti-theft key matching function, so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. 5.1.1 Vehicle connection 1. For most vehicles, just use the included OBD II extension cable to connect the VCI to the vehicle’s DLC port. 2.
CR IMMO User Manual 1. Tap IMMO Matching and select BMW to enter the software. 2. Tap OK. 3. Enter the Anti-Theft System, follow the illustration below to connect the VCI dongle, vehicle and IM2000 PRO to perform the next step.
CR IMMO User Manual 4. If you don’t know the type of the anti-theft System, tap Intelligent Mode to enter. 5. Tap CAS4/CAS4+ anti-theft System, the following screen will appear: 6. Tap Preprocessing to perform Read anti-theft data, Key matching and more. If it has already been preprocessed, here you can perform the relevant functions. The ECU will be upgraded in this process, and files need to be downloaded online. 7.
CR IMMO User Manual 9. Return to the function menu and tap Key Learning. 10.After the key information successfully read, select the unused key position and tap Key Generated By Ignition Switch. 11. Read and display the password, and tap OK. 12. Place a new key close to vehicle coil, tap OK, and wait for the key to generate.
CR IMMO User Manual 13. After the dealer key is successfully generated, please try to start the vehicle. 14. Now the key matching is finished and the new key is ready for use. 5.2 IMMO Programming The IM2000 PRO is required when performing this operation. It has the following functions: • Read transponder data (including Mercedes Benz infrared smart key), and generate exclusive keys. • Read/write on-board EEPROM chip data, and read/write MCU/ECU chip data.
CR IMMO User Manual A. Main diagnostic cable B. OBD I adaptor C. Switching power supply of the IM2000 PRO Notes: You are suggested to connect the VCI dongle shown in below diagram to the tablet via the USB cable. Using a USB cable could effectively enhance your data transmission speed. IMMO Programming does not require a connection to the vehicle. To ensure that the IM2000 PRO works properly, ONLY use the switching power supply and OBD I adaptor to supply power to the IM2000 PRO.
CR IMMO User Manual 5.2.1 EEPROM Programming This function allows you to read/write on-board EEPROM chip data. 5.2.2 Engine Programming This function allows you to read the engine data and write in the backup data after a new engine is replaced. Below procedures show you how to perform engine programming. 1. Tap Engine. 2. Select Engine Brand. 3. Tap Search for ECU model.
CR IMMO User Manual 4. Check ECU model (printed on the sticker on the back of your Engine), enter the engine type in the dialogue box (for example , the engine type should be MED17.7.7) and tap OK. 5. Tap OK to confirm the engine type and enter the function selection screen. Note: The function selection screen varies by differentvehicle manufacturers. a. Tap View Wiring Diagram to check how to connect the engine with the IM2000 PRO.
CR IMMO User Manual D. BENCH mode cable E. Adaptor cable associated with the BENCH mode cable F. Engine b. Tap Backup EEPROM data to create a file name and save it on the tablet. c. Tap Restore EEPROM data to write the backup EEPROM data into the new engine. Stop: The EEPROM restoration applies only when you have encountered irrevocable faults or after a new engine is replaced. d. Tap Backup FLASH data to save the FLASH data on the tablet to avoid accidents. e.
CR IMMO User Manual replacement, and then manually input the original CS code or get the original CS code from the original key. Situation 1: 1. Tap Gearbox. 2. Select Gearbox type according to the specific model, here we choose DQ200-MQB (take this as an example) to enter the function selection screen. Note: The function selection screen varies by differentvehicle manufacturers. 3.
CR IMMO User Manual D. BENCH mode cable E. Adaptor cable for the BENCH mode cable G. Gearbox ECU 4. Tap Connect to read the chip ID of the original car gearbox. 5. Tap Backup EEPROM Data to read the EEPROM data of the original car gearbox and then enter the new file name to save it on the tablet. 6. Tap Backup FLASH Data to back up the FLASH data of the original vehicle gearbox and then enter the new file name to save it on the tablet. 7.
CR IMMO User Manual 10.Tap Restore FLASH Data to write the FLASH data of the original vehicle gearbox backed up in step 6 into the new gearbox ECU. Situation 2: 1. Tap Gearbox. 2. Select Gearbox type according to the specific model, here we choose DQ200MQB (take this as an example) to enter the function selection screen.
CR IMMO User Manual Note: The function selection screen varies by differentvehicle manufacturers. 3. Tap View Writing Diagram to view how to connect the original car gearbox ECU with IM2000 PRO using the BENCH mode cable and its associated adaptor cable. Note: Vehicle gearbox connection could vary depending on gearbox types, for information how to connect the car gearbox, refer to the onscreen connection diagram. D. BENCH mode cable E. Adaptor cable associated with the BENCH mode cable G. Gearbox ECU 4.
CR IMMO User Manual 7. Tap Anti-theft Matching, choose VW to enter the anti-theft system, select MQB Instrument -> Replacement Of Parts -> Transmission, tap OK.
CR IMMO User Manual 8. Tap YES to enter the gearbox replacement screen.
CR IMMO User Manual 9. When replacing the transmission ECU, two groups of anti-theft data are required: • Anti-theft data of transmission engine (backed up in step 5) • Anti-theft data of the target vehicle 1). Select Edit1, tap NO, tap Obtain From EEPROM Data, select the new gearbox EEPROM data backed up in step 5, and tap OK. 2).
CR IMMO User Manual Note: If there is no anti-theft data of the target vehicle, select Original Vehicle Key Obtained, put the original vehicle key in the IM2000 PRO, and just follow the prompts to obtain it, no need to enter any data to complete the replacement. 10.Tap Start Replacement, and input the original car’s VIN code, power level and CS code of the original car instrument according to the information prompts to complete the gearbox replacement.
CR IMMO User Manual Note: If Original Vehicle Key Obtained is selected in step 8, the vehicle’s VIN code, power level and CS code in this step will be automatically obtained. The user is not required to enter any data to complete the replacement. 5.2.4 Key Programming This function allows you to backup old key data, write in data for new keys and detect remote control frequency. 5.2.
CR IMMO User Manual A. Camera Scan: This mode allows you to identify the vehicle model via scanning the vehicle’s VIN. Once scanning is complete, the tablet will enter the diagnostic software of the vehicle directly. B. Enter VIN: In this mode, input the VIN manually to enter the diagnostic software of the vehicle. Input the VIN, and tap OK, the tablet will automatically identify the vehicle model and enter the diagnostic software of the vehicle. 6.
CR IMMO User Manual Systems with fault codes are displayed in red. Systems functioning normally are displayed in black. Explanation of terms: Report: Tap to save the diagnostic result as a diagnostic report in text format. Help: Tap to view the help information of the selected DTC. Compare Results: Tap to select the pre-repair report to compare. By comparison of the pre- and post- repair reports, you can easily identify which DTCs are cleared and which remain unfixed.
CR IMMO User Manual A. Read Fault Code This function displays the detailed information of DTC records retrieved from the vehicle’s control system. Tap Read Fault Code on the test function selection screen, the screen will display the diagnostic result. Explanation of terms: Freeze Frame: A snapshot of critical parameter values at the time the DTC is set. Help: View the help information. Code Search: Search for more information about the current DTC online. Report: Save the current data in text format.
CR IMMO User Manual Notes: Tap to set the display style. indicates sticky top. B indicates this item will be displayed in Bold. A indicates this item will be displayed in Red. There are 3 types of display modes available for data viewing, allowing you to view various types of parameters in the most suitable way. ü Value – Display the parameters in texts and shows in list format. ü Graph – Display the parameters in waveform graphs. ü Combine – Display the parameters in merged graph mode for data comparison.
CR IMMO User Manual Available test vary by vehicle manufacturer, year and model. F. Special Function In addition to amazing & powerful diagnostic function, the tool also features various reset functions, which varies from vehicle to vehicle. 7Maintenance This module provides an easy dial to quickly access the most commonly performed service functions as following.
CR IMMO User Manual To reset the steering angle, first find the relative zero point position for the car to drive in straight line. Taking this position as reference, the ECU can calculate the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle. 7.
CR IMMO User Manual Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced, injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identify injectors to accurately control fuel injection. 7.
CR IMMO User Manual case, this function needs to be done so that the gearbox can automatically compensate according to the driving conditions so as to achieve more comfortable and better shift quality. 7.13 AFS (Adaptive Front-lighting System) Reset This feature is used to initialize the adaptive headlamp system.
CR IMMO User Manual and disabling the remote control key, etc. At this time, the transport mode needs to be deactivated to restore the vehicle to normal. 7.24 AdBlue Reset (Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. 7.25 NOx Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust.
CR IMMO User Manual By default, all diagnostic software is selected. To deselect certain software, tap Unselect, and then check the box next to vehicle model. Tap Update to start downloading. Once download is finished, the software packages will be installed automatically. 9.2 Renew Subscription If the software subscription is due or expires, the system will prompt you to renew your subscription. Tap Renewals on the bottom of the screen to enter the payment screen. 1.
CR IMMO User Manual 4. Tap “Default Print Service”, and choose “Add printer by IP address”. 5. Input the IP address of the printer, and add the printer. 6. Choose the printer, and click the icon to printing the report.
CR IMMO User Manual 10.2 Print via PC A. Paste reports to the PC: 1. Click Personal Center - Settings - Mode Switch, and select “DEVICE MODEL”. 2. Connect the device to the PC via USB cable (Type A to Type C). 3. Cope the report files (.PDF), and paste to the PC. Note: The path of the report files is: .\cnlaunch\CR IMMO\images\ 4. Print the report from the printer connected to the PC. B. Send reports to PC by email: 1. Click “Report” icon to enter the reports display screen. 2.
CR IMMO User Manual 11.4 Subscription Renewal Card This item is used to check the status of the subscription renewal card. 11.5 Profile Use this item to view and configure personal information. 11.6 Change Password Use this item to change the password of the login account. 11.7 Diagnostic Software Clear This item allows you to hide/clear the diagnostic software that is not frequently used. Note: Removing software may completely delete the software from the tool.
CR IMMO User Manual Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE iCarsoft PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS. iCarsoft electronic product is warranted against defects in materials and workmanship for one year from the date of delivery to the user.
CR IMMO User Manual FCC Warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation.
CR IMMO User Manual une autre antenne ou un autre émetteur. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Le matériel a été évalué pour répondre aux exigences générales d’exposition aux radiofréquences.Le dispositif peut être utilisé dans des conditions d ‘exposition portables illimitées. Statement: iCarsoft reserves the rights to make any change to product designs and specifications without notice.
CR IMMO User Manual Information sur les droits d'auteur Droit d'auteur©2021 par Icarsoft Technology Inc. (également appelé iCarsoft en abrégé). Tous droits réservés. Aucune partie de cette publication ne peut être reproduite, stockée dans un système d'extraction ou transmise sous aucune forme ou par quelque moyen que ce soit, électronique, mécanique, par photocopie et enregistrement ou autrement, sans l'autorisation préalable écrite.
CR IMMO User Manuall Précautions de sécurité importantes Pour éviter des blessures corporelles, des dommages matériels ou des dommages accidentels au produit, lisez toutes les informations contenues dans cette section avant d'utiliser l'outil. DANGER • Lorsqu'un moteur fonctionne, gardez la zone de service bien ventilée ou fixez un système d'évacuation du bâtiment au système d'échappement du moteur. Les moteurs produisent divers composés toxiques (hydrocarbures, monoxyde de carbone, oxydes d'azote, etc.
CR IMMO User Manuall Les batteries automobiles contiennent de l’acide sulfurique nocif pour la peau. Pendant l'opération, éviter tout contact avec l’acide de la batterie. Gardez toujours les sources d'inflammation à l'écart de la batterie. Gardez l'outil sec, propre, exempt d'huile, d'eau ou de graisse. Utilisez un détergent doux sur un chiffon propre pour dégager l'extérieur de l'équipement si nécessaire. Gardez les vêtements, cheveux, mains, outils, équipement d'essai, etc.
CR IMMO User Manual Table des matières 1 Contenu du pack......................................................................................... 1 2 Vue d'ensemble........................................................................................... 2 2.1 Introduction.........................................................................................2 2.2 Dongle VCI......................................................................................... 4 2.3 IM2000 PRO..........................
CR IMMO User Manual 1 Contenu du pack Cette liste est fournie à titre indicatif, suivant les revendeurs, le contenu du pack peut être différent. Contacter votre vendeur pour plus d’informations. Numéro Article Descriptions Qt. 1 CR IMMO L'Unité principale 1 2 VCI Dongle VCI 1 3 IM2000 PRO Programmeur d'immobilisation 1 4 Extension d'OBD II Connecte le dongle VCI à la prise OBD du Câble véhicule.
CR IMMO User Manual 17 Câble INS V1 18 Câble INS V2 19 MCU Câble V1 Connectez le programmeur et le tableau de bord du véhicule, puis placez la sonde (le plomb jaune) à la zone désignée. Après avoir retiré le tableau de bord du véhicule, connectez le programmeur, le tableau de bord du véhicule et le câble. Pour connecter le programmeur et MCU.
CR IMMO User Manual 1. Emplacement d'amarrage pour dongle VCI-pour le logement de dongle VCI. 2. Dongle VCI - Il est pré-installé dans la fente d'accueil sur le dessus de la tablette d'affichage. Utilisez la main pour appuyer sur le dongle une fois, il sera automatiquement éjecté de la fente d'amarrage. Lorsqu'il n'est pas utilisé, veuillez le réinsérer dans la fente pour éviter toute perte. 3. Touche d'alimentation- Appuyez dessus pour allumer/éteindre l'outil. 4. Écran LCD-Indique les résultats du test.
CR IMMO User Manual • • • • • • Résolution: 1280*800 pixel Caméra: Caméra arrière 8MP Tension de travail: 5V Courant de travail: 3A Environnement de travail: 0 ~45 Environnement de stockage: -10 ~60 2.2 Dongle VCI Ce dongle fonctionne comme un dispositif VCI (Interface de communication du véhicule). Il est utilisé pour obtenir les données du véhicule, puis l'envoyer à la tablette pour analyse via Bluetooth. 1.
CR IMMO User Manual 2.3 IM2000 PRO L'IM2000 PRO fonctionne comme un programmeur d’antidémarrage antivol dédié. Il doit fonctionner avec la tablette d'affichage pour effectuer les opérations de correspondance IMMO (pour certains véhicules) et de programmation IMMO. 1. Connecteur de diagnostic DB26-Se connecte au collecteur infrarouge Mercedes Benz, au câble ECU et au câble MCU etc. 2. Fente de clé infrarouge Mercedes Benz-Contient la clé Mercedes Benz. 3.
CR IMMO User Manual Paramètres techniques • • • • Tension d'entrée: 12 V Courant d'entrée: 500mA Environnement de travail: 0 ~50 Environnement de stockage: -20 ~70 3 Utilisation initiale 3.1 Charge Suivez les étapes ci-dessous pour charger la tablette: 1. Connectez une extrémité du câble de charge à la prise USB de l'adaptateur secteur. 2. Connectez l'autre extrémité au port de charge situé au bas de l'hôte. 3. Branchez la fiche d'alimentation du chargeur sur une prise de courant.
CR IMMO User Manual précédent ou aux sorties. 3.4 Changer la langue du système L'outil prend en charge plusieurs langues. Pour changer la langue de l'outil, veuillez procéder comme suit: 1. Sur l'écran d'accueil, appuyez sur Paramètres-> Système-> Langue et entrée> Langues. 2. Appuyez sur Ajouter une langue, puis choisissez la langue souhaitée dans la liste. 3. Appuyez et maintenez la langue souhaitée et faites-la glisser vers le haut de l'écran, puis relâchez-la, elle se transformera en langue cible. 3.
CR IMMO User Manual A. Si vous êtes un nouvel utilisateur, appuyez sur Nouvel enregistrement et suivez les instructions à l'écran pour terminer l'inscription. 1. Créer un compte App: Remplissez les informations dans chaque champ (les éléments avec * doivent être remplis). Après la saisie, appuyez sur S'inscrire. 2. Activer VCI: Saisissez le numéro de série de produit à 12 chiffres et le code d'activation à 8 chiffres (peut être obtenu à partir de l'enveloppe de mot de passe), puis appuyez sur Activer. 3.
CR IMMO User Manual 4 Pour Commencer 4.1 Menu principal Il comprend principalement les éléments suivants: Adaptation IMMO Programmation IMMO Diagnostiquer Maintenance Mise à jour Rétroaction Autres Cette fonction vous permet d'effectuer la fonction d'appariement de la clé antivol, de sorte que le système de contrôle antidémarrage sur la voiture identifie et autorise les clés de contrôle à distance pour normalement utiliser la voiture.
CR IMMO User Manual 4.2.2 Connexion du véhicule Suivez les étapes mentionnées ci-dessous pour connecter le véhicule en OBDII : 1. Localisez la prise OBD du véhicule. 2. Branchez le dongle VCI dans la prise OBD du véhicule (il est suggéré d’utiliser le câble d’extension OBDII pour connecter le dongle VCI et la prise OBD). Pour le véhicule non-équipés dune prise OBDII, procédez comme suit : 1.Sélectionnez l’adaptateur correspondant en fonction du type de prise de votre véhicule. 2.
CR IMMO User Manual 5 Fonctionnements d'anti-démarrage 5.1 Correspondance anti-vol Cette fonction vous permet d'effectuer la fonction d'appariement de la clé antivol, de sorte que le système de contrôle antidémarrage sur la voiture identifie et autorise les clés de contrôle à distance pour normalement utiliser la voiture. 5.1.1 Connexion du véhicule 1. Pour la plupart des véhicules, utilisez simplement le câble d'extension OBD II inclus pour connecter le VCI à la prise OBD du véhicule. 2.
CR IMMO User Manual 1. Appuyez sur Adaptation IMMO et sélectionnez BMW pour entrer dans le logiciel. 2. Appuyez sur OK. 3. Entrez dans le système antivol, suivez l'illustration ci-dessous pour connecter le dongle VCI, le véhicule et IM2000 PRO pour effectuer l'étape suivante.
CR IMMO User Manual 4. Si vous ne connaissez pas le type du système antivol, appuyez sur Mode intelligent pour entrer. 5. Appuyez sur Système antivol CAS4/CAS4, l'écran suivant apparaîtra: 6. Appuyez sur Prétraitement pour effectuer la lecture des données antivol, la correspondance des clés et plus encore. S'il a déjà été prétraité, vous pouvez ici effectuer les fonctions pertinentes. L'ECU sera mis à niveau dans ce processus et les fichiers doivent être téléchargés en ligne. 7.
CR IMMO User Manual 9. Revenez au menu des fonctions et appuyez sur Apprentissage des clés. 10.Une fois les informations clés lues avec succès, sélectionnez la position clé inutilisée et appuyez sur Clé générée par le commutateur d'allumage. 11. Lisez et affichez le mot de passe, et appuyez sur OK.
CR IMMO User Manual 12. Placez une nouvelle clé à proximité de la bobine du véhicule, appuyez sur OK et attendez que la clé génère. 13. Une fois la clé du concessionnaire générée avec succès, veuillez essayer de démarrer le véhicule. 14. Maintenant, la correspondance des clés est terminée et la nouvelle clé est prête à l'emploi. 5.2 Programmation IMMO L'IM2000 PRO est requis lors de l'exécution de cette opération.
CR IMMO User Manual A. Câble de diagnostic principal B. Adaptateur OBD I C. Commutation de l'alimentation électrique de l'IM2000 PRO Remarques: Il vous est suggéré de connecter le dongle VCI illustré dans le diagramme ci-dessous à la tablette via le câble USB. L'utilisation d'un câble USB pourrait améliorer efficacement votre vitesse de transmission de données. La programmation IMMO ne nécessite pas de connexion au véhicule.