User Manual

ManualsBrandsIC Realtime ManualsElectronics2MP IP Indoor/Outdoor Small Fixed Lens Bullet Camera with PoE

Quick Start Guide

HD IR Mini Bullet

Network Camera

Features and Speciﬁcations

A. Overview

B. Camera Interface

Camera Installation

A. Installation Steps

B. Restore Factory Defaults and

Installing SD card

Quick Conﬁguration Tool

A. Overview

B. Operation

Web Operation

A. Network Connection

B. Login and Logout

Appendices

C. FAQ

D. Toxic or Hazardous Elements

3-4

5-6

7-8

9-10

Table Of Contents

MARGIN

GUIDES

To see the guides to go:

View / Guides / Show

Guides

www.icrealtime.com

IMPORTANT SAFEGUARDS AND WARNINGS

Electrical Safety

All installation and operation here should conform to your local electrical safety codes. The

power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the

Limited power source is rated 12V DC in the IEC60950-1. This series product supports PoE

too. Please note: Do not connect these two power supplying sources to the device at the same

time; it may result in device damage! We assume no liability or responsibility for all the ﬁres or

electrical shock caused by improper handling or installation. We are not liable for any problems

caused by unauthorized modiﬁcation or attempted repair.

Transportation Security

Care must be given to avoid heavy stress, violent vibration or water damage during

transportation, storage and installation.

Installation

Do not apply power to the camera before completing installation. Please install the proper

power cut-off device during the installation connection. Always follow the instruction guide the

manufacturer recommended.

Qualiﬁed engineers needed

All the examination and repair work should be done by the qualiﬁed service engineers. We are

not liable for any problems caused by unauthorized modiﬁcations or attempted repair.

Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,

inﬂammable, explosive substances and etc. Please keep it away from the electromagnetic

radiation object and environment. Please make sure the CCD (CMOS) component is out of the

radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component

damage. Please keep the sound ventilation. Do not allow the water and other liquid falling into

the camera. Lightning-proof device is recommended to be adopted to better prevent lightning

damage. The grounding studs of the product are recommended to be grounded to further

enhance the reliability of the camera.

Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily

maintenance work. Do not touch the CCD (CMOS) optic component. You can use the blower to

clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is

too much dust, please use the water to dilute the mild detergent ﬁrst and then use it to clean

the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect

the CCD (CMOS) component when you do not use the camera.

Accessories

Be sure to use all the accessories recommended by manufacturer. Before installation, please

open the package and check all the components are included. Contact your local retailer ASAP

if something is broken in your package.

Summary of content (10 pages)

PAGE 1
IMPORTANT SAFEGUARDS AND WARNINGS Electrical Safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1. This series product supports PoE too.
PAGE 2
1A. OVERVIEW This series network camera integrates the traditional camera and network video technology. It adopts video data collection and transmission together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 and H.265 video compression technology, which maximally guarantees the video quality. It powers with either 12VDC or POE. The camera supports the IR night vision function.
PAGE 3
2A. INSTALLATION STEPS Step 1 Mark the mounting points for the camera and then drill the mounting holes as well as a cable pass through hole if necessary. See Figure 2-1. Figure 2-1 Step 2 Install the expansion bolts if necessary. Thread the base screws through the mounting holes in the base of the camera. See Figure 2-2. Figure 2-2 3 | www.icrealtime.com Step 3 Pull the cables through (if applicable) and tighten down the camera base screws. See Figure 2-3.
PAGE 4
. Step 5: Tighten down the mounting screws. See Figure 2-5. Waterproof connector installation for network port (if applicable): For a device with a plastic enclosure, you can directly rotate the dome enclosure clockwise, cover the dome enclosure and complete installation. See ﬁgure 2-9. Figure 2-5 Adjusting Sunshield and Angle: ● Use the supplied wrench to loosen set screw and adjust shade. Tighten down Screw when ﬁnished. See Figure 2-7. ● To Adjust Angle, loosed the set screw and rotate the camera.
PAGE 5
2B. RESTORE FACTORY DEFAULTS/ INSTALL SD CARD Important: Make sure the device is powered when attempting to press RESET button. 3A. OVERVIEW The IP Conﬁg tool is used to search the local network for IC Realtime devices as well as modify the IP addresses and upgrading ﬁrmware. Step 1 Use the supplied hex wrench to unscrew the access panel below the camera. Skip to Step 3 if only installing SD card. This software can be downloaded at: https://icrealtime.
PAGE 6
Select “Search Setting” to modify the IP range to scan for and input the correct login information for the device. See Figure 3-2. Figure 3-2 Note: If the Camera status is “Uninitialized,” select the camera and the click the “Initialize” icon on the bottom left side and follow the process on screen to initialize the device. The Operate column will allow you to modify device, view device information and link to web browser. See ﬁgure 3-3. Figure 3-3 6 | www.icrealtime.
PAGE 7
This series network camera product supports the Web access and management via PC. 4A. NETWORK CONNECTION Please follow the steps listed below for network connection. ● Make sure the network camera is connected to the network and powered properly. ● Please set the IP address, subnet mask and gateway of the PC and the network camera respectively. The camera is set to DHCP out of the box with default IP address of 192.168.1.108 if DHCP pool is not available. Subnet mask is 255.255.255.0. Gateway is 192.168.1.
PAGE 8
Web includes several modules: monitor channel preview, system conﬁguration, alarm and etc. See Figure 4-3. ● ● ● ● Live: Live video of camera Setup: For conﬁguration changes. Alarm: For monitoring alarm triggers (motion detect, IVS, abnormalities, etc) Logout: Logs out of the camera web GUI Figure 4-3 Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. 8 | www.icrealtime.
PAGE 9
5A. FAQ Device does not operate properly/ lost password. Please refer to section 2B for factory reset process. Cam will need to be Initialized after factory reset. P2P status is “not connected/ oﬄine” The water leakage. The front or rear cap if damaged or removed can result in water leakage. The glass dome may also have been compromised from heavy strikes or heavy pressure. The waterproof plug of the rear cap may also have loosened. Camera does not show up on local network.
PAGE 10
X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these (substances or elements) will not result in any severe environmental pollution, any bodily injury or damage to any assets.