iBaby Labs, Inc.
iBaby MonitorUser Manual Content 1 2 3 4 PRODUCT OVERVIEW.......................................................................................................................... 3 1.1 PACKING LIST ........................................................................................................................... 3 1.2 INTERFACE INTRODUCTION ....................................................................................................... 3 1.3 PRODUCT SPECIFICATIONS .................
iBaby MonitorUser Manual 1 Product Overview 1.1 Packing list iBabymonitor*1 Wall bracket *1 User manual *1 Power adapter *1 1.2 Interface Introduction Photosensitive sensor Lens Microphone LED status light Reset button Temperature&humidity sensor interface Power interface 1) LED status light: Indicates the current working status of the machine, see Table 1 of Section 4.1 2) Power interface 3) Reset button: Long press to restore the device to factory settings.
iBaby MonitorUser Manual 1.3 Product Specifications Model:M2C compression method Video H.264 Frame rate 1~12 frames Resolution Ultra (1920*1080),HD(1280*720),VGA(640*480) standard:4.0mm F=2.
iBaby MonitorUser Manual material Use environment Product power within 2.
iBaby MonitorUser Manual 2.3 Account registration and login 1. New users Press the App prompt to register an account. The account number must be an actual and valid mailbox, and the password must be a combination of letters (case sensitive) and numbers, and the length is 6 characters or more. Login will be completed automatically after registration is completed. Note: The real mailbox is convenient for recovering the password and obtaining technical support reply when you forget the password. 2.
iBaby MonitorUser Manual 3. After confirming that the prepared content is complete, click the "Next" button. 4. Go to the following page, enter the correct Wi-Fi password, and click the “Next” button to enter the device activation process.
iBaby MonitorUser Manual 5. Activate the progress display, please wait for the activation progress to complete automatically and jump to the video control main interface (this process lasts about 1 minute), you can start normal use. Note: If you have not activated successfully, please refer to the “Installation Questions” section in section 4.2 of this document.
iBaby MonitorUser Manual 3 APP operation and function introduction 3.1 Video control main interface Functional navigation area Information display area Function button area 收听: 1. Functional navigation area: :Function menu navigation button. Click on the left side to slide out the function menu page. :Device list. When multiple devices are installed, click to switch to watch other devices. :Media library. Display alarms, manual recording/photographing media files. 2.
iBaby MonitorUser Manual :Listen button. Receive sound from the device side. :Speech button.Transfer the sound to the device side. :Record button. Record the current video, The video file is saved in the media library. :Music button.Enter the music play page. :Capture button. Capture the current video, the image is saved in the media library : Air quality icon. Display the current air quality level, click to view historical data. 3.
iBaby MonitorUser Manual My account: personal information display and settings Settings: device parameters, information settings Contact us: Contact iBaby Logout / Logout: Exit the current account 3.3 Introduction to common functions 3.3.1 Alarm setting function Motion alarm: An alarm that is triggered when an object moves in the screen. The higher the sensitivity level, the more sensitive it is. Audible alarm: The alarm that is triggered when the ambient sound reaches the alarm level.
iBaby MonitorUser Manual Alarm action type selection: Picture: When moving or audible alarm, capture 3 pictures and upload them to the media library for encryption. Video: When moving or audible alarm, record a short 15 second video and upload it to the media library for encryption. Alarm only: Only alarm message notifications are made and media files are not stored. 3.3.2 Invite & View Users This feature invites family members or friends to work with the device.
iBaby MonitorUser Manual amount generated per second is not more than 96kpbs Medium 128kbps: medium quality, taking up less bandwidth. The amount generated per second is not less than 128kpbs Good 256kbps: good picture quality (720P effect), occupying moderate bandwidth. The amount generated per second is not more than 256kpbs Excellent 512kbps: The best picture quality (1080P effect), occupying a large bandwidth.
iBaby MonitorUser Manual 3.3.6 Version Information As shown in the following figure, you can view the version of the APP, the version of the device firmware, and the serial number of the device. If a new version of the firmware is released, it can be updated to the latest firmware via the "Firmware Upgrade" button.
iBaby MonitorUser Manual 4 FAQs 4.1 Device LED Status Light Meaning LED status Meaning Red slow flashing The device is not connected to WI-FI, to be activated. Green slow flashing The device is connected to WI-FI but has not been activated yet. Steady red The device is activated without being connected to WI-FI. Steady green The device is working normally. Red light and green light alternately flashes Device startup. No light The device is not powered or faulty. Table 4.1 4.
iBaby MonitorUser Manual Answer: Red indicates that iBaby is not connected to your WI-FI. The solution is as follows: 1) Please use the USB cable that comes with the original phone to ensure good transmission. 2) Please install iBaby in a place with good WI-FI signal. The WI-FI name and password are preferably 8-32 characters in upper and lower case letters, numbers, - or underscores. They cannot contain special characters (such as Chinese characters, Japanese). , Korean, etc.).
iBaby MonitorUser Manual Answer: Red indicates that iBaby is not connected to your WI-FI. The solution is as follows: 1) Please confirm the WI-FI password, and then restart the device and re-install it. 2) Please install iBaby in a place with good WI-FI signal. The WI-FI name and password are preferably 8-32 characters in upper and lower case letters, numbers, - or underscores. They cannot contain special characters (such as Chinese characters, Japanese). , Korean, etc.).
iBaby MonitorUser Manual Answer: The green flashes slowly, indicating that the device is connected to your WI-FI but has not been activated on the server. Please exit the app from the background of the mobile phone, then run the APP, and turn off the router and device. If it still doesn't work, please re-install it in a different period of time and the device does not need to be reset.
iBaby MonitorUser Manual 4.3 Keep Loading Question 1 When viewing at home, the screen compares cards, which is slower (LED status lights behind iBaby, sometimes green, sometimes red) Answer: Sometimes red, sometimes green, indicating that the WI-FI signal is not stable enough at the time, or the nearby WI-FI interference is serious, and it needs to be optimized from the following aspects: 1) If the router is a normal 2.4G, it is recommended to log in to the router to optimize the WI-FI settings.
iBaby MonitorUser Manual Answer: Red indicates that iBaby is not connected to your WI-FI. Please try the following steps: 1) The device is powered up and restarted to see if the LED light turns green. 2) The router is heavily loaded at the time, and the router is powered on and restarted. 3) iBaby is too far away from WI-FI, or there are too many middle partition walls. It is recommended to try it near the WI-FI signal. 4) The router should be cool and not too old.
iBaby MonitorUser Manual mobile phone must be fast. 1) Try to lower the resolution of the device. 2) The mobile app is closed in the background and reopened. 3) The device is powered up and restarted. 4.4 Usage issues Question 1 When listening to the intercom at the same time, the noise is very loud. Answer: The phone is too close to the device, it is recommended to be 10 meters away to reduce the crosstalk. The device is placed at home and there is no such problem when going out.
iBaby MonitorUser Manual 1) Is the base placed? The temperature and humidity module is built into the magnetic base. The iBaby and the three metal domes on the base should be aligned and placed flat. It is best to pick up the iBaby and pick up the magnetic base. 2) Is the iBaby firmware version up to date? APP Settings Menu - "Settings -" Device & Application Information page, confirm the firmware version is 1.8.1 and above.