Quick Start Guide

System Setup
1
Port Connections
Secure the media player to the monitor.4
Connect the HDMI cable and AC adapter.5
back of the monitor.
3
Boot up
Plug in the AC adapter to the media player and it
will power on automatically.
Once the user has exited the boot up screen,
users can go through system configurations in both
landscape and portrait orientations.
1
Kensington lock
2
Wireless antenna post
3
Micro SD card slot
4
Audio out
5
Ethernet
6
HDMI out
7
DC in
8
ADB
9
Power LED
10
USB port
11
Reset
12
Mounting hole (screw spec: M4)
2 1
11
10
6 754
3
8 9
12
HDMI Cable
Adapter Cable
CAUTION
- Replacement of a battery with an incorrect type that can be defeat a safeguard;
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a
battery, that can result in an explosion;
- Leaving a battery in an extremely high temperature surrounding environment that can
result in an explosion or the leakage of flammable liquid or gas;
- A battery subjected to extremely low air pressure that may result in an explosion or the
leakage of flammable liquid or gas.
Risk of explosion if the battery is replaced by an incorrect type
Wait one-half hour after switching off before handling parts
IAD_DGS_X75_10EP P.6 P.2P.1
IAD-16006
Quick Start Guide
This printed quick guide provides a quick walk-through of the set up process. For
complete documentation, please visit http://support.IAdea.com.
Box Content
Media player unit Power adapter
Mounting and Installation (USB mouse required)
Attach the wirelss antenna by screwing the antenna clockwise onto the post.
Wi-Fi antenna
1
2
Mount the media player to the back of the monitor using the velcro.
Seperate the velcro stripe into singles.1
surface of the media player.
2
Velcro (2 sets)
HDMI cable
HDMI Cable
Adapter Cable
Q41M78SP05906C
Power bracket and
micro SD card bracket
screw*2
company Name: IAdea Corporation
Address: 3F, No. 21, Lane 168, Xingshan Road,Neihu Dist. Taipei, 114 Taiwan
Tel: [phone]
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innova-
tion, Science and Economic Development Canada’s licenceexempt RSS(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference.
(2)This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en comprom-
ettre le fonctionnement.
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure and Industry Canada RSS-102
RF exposure limits set forth for an uncontrolled environment. This device and its antenna
must not be co-located or operating in conjunction with any other antenna or transmitter.
To comply with FCC RF exposure and Industry Canada RSS-102 RF exposure compli-
ance requirements, this grant is applicable to only Mobile Configurations. The antennas
used for this transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
Cet equipement est conforme aux limites d’exposition aux rayonnements enoncees pour
un environnement non controle et respecte les regles d’exposition aux frequences radioe
lectriques (RF) CNR-102 de I’IC. Cet equipement doit etre installe et utilize en gardant
une distance de 20 cm ou plus entre le radiateur et le corps humain (a I’exception des
extremites : mains, poignets, pieds et chevilles).