User Manual

ManualsBrandsI/OMagic ManualsComputers & AccessoriesI/O Magic Internal CD-RW Drive (I522452) (ICDRW5252)

Quick Installation Guide

This guide is intended to help you install the hardware and

software necessary for you to start using the CD-RW drive. For

more detailed information about the hardware and software,

please refer to the user manual included w ith this drive.

Package Content

• CD-RW Drive

• User’s Guide

• Registration Card

• CD Mastering software

• Quick Install Guide (This Document)

Hardware Installation

1. Connect the power cable from the system’s power supply to the

drive. (see diagram below)

2. The IDE Interface cable (gray ribbon) connects to the back of the

drive and goes into the Hard Disk Controller on the motherboard.

3. Connect one end of the CD Audio (Analog) Cable into the Audio

Out port on the drive, and the other end to the Audio In port of your

sound card. (The audio cable is only used for CD music playback.)

4. Secure the drive to your computer’s chassis. (Use the appropriate

screws)

Software Installation

1. Insert the Nero-Burning ROM installation CD into your CD-

ROM Drive.

2. The CD will automatically run and start the installation

program.

3. If the installation program does not launch automatically,

click on the “Start” button on the taskbar and select “Run”.

Type D:\Setup (Where D:\ is your CD-ROM drive).

4. Follow the onscreen instructions. The installation program

will guide you through the entire installation.

Jumper Setting

1. Before installing the drive into your system, make sure the

jumper setting is set correctly.

2. If the writer will be the only device connected to the IDE

cable (gray ribbon), it should be set to Master (MA).

5. You may need to restart the computer after Nero has been

installed.

6. To start using the Nero Burning Rom software, click the

"Start" button on the taskbar, go to "Programs", then cl

ick on

"Nero-Burning Rom".

7. You are now ready to burn a CD.

3. If the writer will be sharing the IDE cable with another

device, one device should be set as Master and the other

set as Slave (SL). (MA recommended for writer on

secondary IDE)

4. To set the drive as the Master drive, move the jumper to the

MA position as shown above.

5. To set the drive as the Slave drive, move the jumper to the

SL position as shown above.

5. Once all the cables are connected properly, close the computer

case and turn on your system.

6. Windows will automatically detect the drive and automatically install

the necessary drivers for the drive. (Win 95, 98, 2000)

7. If you are using Windows NT, go to Start > Settings > Control Panel

> Devices. Select “ATAPI” from the list, then click “startup” and

make sure “Boot “ is checked. Restart your computer.

8. After Windows has finished loading, go to “My Computer” and verify

that the drive has been installed. You should see another drive

letter for your new drive. (Example (E:\))

9. You are now ready to proceed with the software installation.

How to Create a CD with Nero

Burning Rom

AC-QI-001

Note: If Installation did not go accordingly, please refer

to the user’s manual for more detailed instructions.

We recommend you update Nero to its latest version.

You can do so for free at http://www.nero.com

No drivers are required for this Plug & Play unit to work.

Summary of content (2 pages)

PAGE 1
CD-RW 2 Quick Installation Guide 3 This guide is intended to help you install the hardware and software necessary for you to start using the CD-RW drive. For more detailed information about the hardware and software, please refer to the user manual included w ith this drive. Hardware Installation Software Installation 1. Connect the power cable from the system’s power supply to the drive. (see diagram below) 1. Insert the Nero-Burning ROM installation CD into your CDROM Drive. Package Content 2.
PAGE 2
Duplicating a CD (CD-Copy) Creating a Music CD Click Here 1. To being using Nero, Click Start > Programs > Nero-Burning Rom. 2. You can use 2 CD drives to perform a CD-Copy. 3. Insert the source CD into your CD-ROM drive, and a blank CD disk into the writer. (Note: Use CD-R media if copying music CDs) 4. Select “CD-Copy” from the New Compilation window. 5. Select the Write Speed. 6. 7. Click Here Select “Audio-CD” from the New Compilation window and click the “New” button. 1.