User Manual and Installation Guide Wireless Full HD Sender Transmitter HD-W300T ® R E ADY www.hdflow.co.kr ver 1.
CONTENTS Safety Precautions .......................................................................................................................................................................3 Read Before Operating Equipment .........................................................................................................................................3 Unit Care Recommendations ......................................................................................................................
SAFETY PRECAUTIONS Keep the product out of reach of children. Keep the product away from external heat sources such as heaters or stoves. If there is any unusual sound, smoke or odor coming from the product, immediately unplug the product. Keep the battery of remote control out of reach of children. Do not attempt to open the outer case of the Transmitter or Receiver. Doing so will void the product warranty. Keep the remote control away from humidity and/or liquids.
INTRODUCTION HD FLOW3 Wireless AV Multi Display System provides Full HD 1080p signal transfer, including 3D signal*, without the hassle of running cables.
PRODUCT SPECIFICATIONS HD-W300T Video Input (Transmitter) 3x HDMI up to 1080p60 1x HDMI pass-thru output (pass-thru port mirrors HDMI 1) 1x PC Video 1x Component & composite (via included dongle) Video Output (Receiver) 1x HDMI up to 1080p60 1x Component 1x Composite Encoding Decoding Wireless Connection Wire Connection USB Audio Audio Input Audio Output Video Resolution Video Latency Frequency Range Multicast Security HDCP Version Antenna Type IR Emitter Control Remote Power H.264 Baseline Profile H.
Transmitter Front 1. Power/Link Indicator Light • Blinking indicator light - Establishing link between the Transmitter and the Receiver. • Solid indicator light - Link between the Transmitter and Receiver has been established and is ready for signal transmission. 2. HDMI 1 • The HDMI 1 indicator light will be illuminated when the HDMI 1 port is selected for video input. • If there is no signal, and/or the cable is not connected, the indicator light will blink. 3.
Transmitter Back 1. HDMI 1 IN • HDMI1 input port. 2. HDMI Pass-Thru • Outputs a duplicate of the source that is plugged into HDMI 1. 3. HDMI 2 IN • HDMI2 input port. 4. HDMI 3 IN • HDMI3 input port. 5. USB • USB port is used for service only. 6. IR-OUT • Connects IR Flasher to the Transmitter for remote control of external devices which are connected to the Transmitter (i.e. Blu-Ray player, DVD, STB, etc). 7. PC AUDIO-IN * • Stereo audio input port for PC, component, or composite source. 8.
Receiver Front 1. Power/Link Indicator Light • Blinking indicator light - Establishing link between the Transmitter and the Receiver. • Solid indicator light - Link between the Transmitter and Receiver has been established and is ready for signal transmission. 2. HDMI • The HDMI indicator light will be illuminated when the HDMI port is selected for video output. • If there is no signal, and/or the cable is not connected, the indicator light will blink. 3.
Receiver Back 1. HDMI-OUT • HDMI output port 2. AV-OUT • Composite video output port 3. IR-IN * • Connects IR Extender in order to extend IR reception range. 1 4. AUDIO-OUT ** • 3.5mm stereo audio output port for component output. 5. COMPONENT-OUT ** • Component Video output port 6. USB • USB port used for service 2 7. LAN • LAN port used for wired connection alternative 8. DC • 12V DC Power Input * For Better IR reception range, use the IR input port with IR extender (not included).
Remote Control 1. POWER ON Button • Turns the Transmitter and Receiver power ON 2. POWER OFF Button • Turns the Transmitter and Receiver power OFF 3. 4. 1 8 INFO/OK* • Displays the following information on the screen: Transmitter - WiFi IP, LAN IP, and Source Resolution. Note: The Transmitter unit’s information will only be displayed if the connection between the Transmitter unit and Receiver has been established.
INSTALLATION AND OPERATION Before starting the installation, please ensure that all source components (Blu-ray player, cable box, etc.) and the display equipment (TV, display, projector, etc.) are turned off. For initial setup of your HD FLOW3 system complete steps A, B, C, D, E and F in order. A) Connecting Source Components To The Transmitter a. HDMI Media Source • Note: It is recommended that HDMI1 input port be used if only one HDMI source component is present.
d. Composite Media Source • Video – Connect “yellow” composite video RCA to green port on Component/Composite Adaptor. • Audio – A 3.5mm stereo audio cable is required (not included) to transmit audio when using this input. Connect the 3.5mm stereo audio cable from the VGA source component’s audio output to the Transmitter's PC AUDIO-IN port.
D) Connecting The Receiver To The Display Device Note: Connect the Receiver to the display device using the port with the highest capable resolution; HDMI port is preferred. The HD FLOW3 is a video switch, and as such will upconvert all inputs with resolutions of 480p, 720p, and 1080i/p through the HDMI Output. A. HDMI Output to Display • Connect the HDMI cable from the Receiver's HDMI output to the display device's HDMI input. B.
Multicast Mode - Pairing Additional Receiver(s) With The Transmitter (Optional) Multicast Wireless Mode enables the Transmitter to stream AV media from one Transmitter to up to six Receivers. Note: Your HD FLOW3 Wireless AV Multi-Display System comes pre paired. This section is only needed if you have separately purchased additional Receiver(s).
Tips If the Transmitter and Receiver are not establishing a connection: 1. It is recommended to unplug the power to both units for 30 seconds and then plug them back in. 2. If the above tip does not assist, please reference the Factory Reset section of this manual. If the connection has been established and the HD FLOW3 logo can be seen on the display device, but content is not playing when initiated: 1. Ensure that source cables are properly connected. 2.
Supported Video Formats Video Standard Resolution 640 x 480p60 640 x 480p70 640 x 480p85 800 x 600p60 800 x 600p70 800 x 600p85 1024 x 768p60 1024 x 768p70 1024 x 768p85 1152 x 864p60 "VESA 1152 x 864p70 Format 1152 x 864p85 (PC standard)" 1280 x 800p60 1280 x 960p60 1280 x 960p70 1280 x 960p85 1280 x 1024p60 1360 x 768p60 1440 x 900p60 1600 x 1200Rp601 1600 x 900p60 1680 x 1050p60 720 x 480I60(NTSC) 720 x 576I50(PAL) 720 x 480p60 720 x 576p50 1280 x 720p50 1280 x 720p60 "DTV Format 1920 x 1080i50 (TV sta
COMPLIANCE STATEMENTS FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
WARRANTY 1 YEAR LIMITED WARRANTY The HD FLOW3 offers the highest quality components and technology available. The product is warranted to be free from defects in material and workmanship, given normal use and care, for 1 Year from the original purchase date with proof of purchase. Please retain a copy of your receipt as you will need this to obtain warranty work. We will repair or replace the product which fails as a result of such a defect during the warranty period.
Wireless Full HD Sender Transmitter www.hdflow.co.kr I DO IT Co., Ltd. #637, Smart-Hub Industry-University Convergence Center, 237 Sangidaehak-ro, Siheung-si, Gyeonggi-do, Korea Tel : +82 (0)31 8041 1500 Fax : +82 (0)31 8041 1550 E-mail : sales@hdflow.com I DO IT France 6-8 Rue de la Closerie ZAC Du Clos Aux Pois 91090 LISSES Cedex FRANCE Tel : +33 (0)1 64 97 52 28 Fax : +33 (0)1 64 97 52 35 E-mail : sales@i-do-it.