User Manual and Installation Guide Wireless Full HD Sender Receiver HDM-W300R ® R E ADY www.hdflow.co.kr ver 1.
CONTENTS ..............................................................................................................3 Safety Precautions Read Before Operating Equipment .................................................................................3 Unit Care Recommendations Introduction Features ..........................................................................................3 ...................................................................................................................
SAFETY PRECAUTIONS Keep the product out of reach of children. Keep the product away from external heat sources such as heaters or stoves. If there is any unusual sound, smoke or odor coming from the product, immediately unplug the product. Keep the battery of remote control out of reach of children. Do not attempt to open the outer case of the Transmitter or Receiver. Doing so will void the product warranty. Keep the remote control away from humidity and/or liquids.
INTRODUCTION HD FLOW3 Super mini Wireless AV Multi Display System provides Full HD 1080p signal transfer, including 3D signal*, without the hassle of running cables.
PRODUCT SPECIFICATIONS HDM-W300R Video Input (Transmitter) 3x HDMI up to 1080p60 1x HDMI pass-thru output (pass-thru port mirrors HDMI 1) Video Output (Receiver) 1x HDMI up to 1080p60 Encoding Decoding Wireless Connection Audio Video Resolution Video Latency Frequency Range Multicast Security HDCP Version Antenna Type IR Emitter Control Remote Power H.264 Baseline Profile H.264 Baseline, Main, High Profile IEEE 802.11n 2 CH PCM, 48kHz, 16 Bit 480i/p, 720p, 1080i/p (24/30 fps) 21mS 5.15~5.25GHz / 5.
Transmitter Front 1. Power/Link Indicator Light • Blinking indicator light - Establishing link between the Transmitter and the Receiver. • Solid indicator light - Link between the Transmitter and Receiver has been established and is ready for signal transmission. 2. HDMI 1 • The HDMI 1 indicator light will be illuminated when the HDMI 1 port is selected for video input. • If there is no signal, and/or the cable is not connected, the indicator light will blink.
Receiver Front 1. 2. 3. 4. Power/Link Indicator Light • Blinking indicator light - Establishing link between the Transmitter and the Receiver. • Solid indicator light - Link between the Transmitter and Receiver has been established and is ready for signal transmission. HDMI • The HDMI indicator light will be illuminated when the HDMI port is selected for video output. • If there is no signal, and/or the cable is not connected, the indicator light will blink.
Remote Control 1. POWER ON Button- Turns the Transmitter and Receiver power ON 2. POWER OFF Button- Turns the Transmitter and Receiver power OFF 3. 4. INFO/OK*- Displays the following information on the screen: • Transmitter - WiFi IP and Source Resolution. Note: The Transmitter unit’s information will only be displayed if the connection between the Transmitter unit and Receiver has been established. • Receiver - WiFi IP, WiFi Channel, SSID, Display Resolution, WiFi Reception Strength.
INSTALLATION AND OPERATION Before starting the installation, please ensure that all source components (Blu-ray player, cable box, etc.) and the display equipment (TV, display, projector, etc.) are turned off. For initial setup of your HD FLOW3 Super mini system complete steps A, B, C, D, E and F in order. A) Connecting Source Components To The Transmitter a. HDMI Media Source • Note : It is recommended that HDMI1 input port be used if only one HDMI source component is present.
C) IR Extender Installation (Optional) Install the IR Extender by plugging in the IR Extender (not included) into the IR-IN port on the Receiver. (IR Extender use is optional. Use the IR Extender when the Receiver is out of sight or to extend the range of the Receiver's IR reception range.) D) Connecting The Receiver To The Display Device Note : Connect the Receiver to the display device using the port with the highest capable resolution.
Multicast Mode - Pairing Additional Receiver(s) With The Transmitter (Optional) Multicast Wireless Mode enables the Transmitter to stream AV media from one Transmitter to up to six Receivers. Note: Your HD FLOW3 Super mini Wireless AV Multi-Display System comes pre paired. This section is only needed if you have separately purchased additional Receiver(s).
Factory Reset CAUTION: systems (systems with two or more receivers) as the pairing will be forgot. One will have to re-pair the additional receivers if a factory reset is completed. To complete a factory reset, complete each of the steps below for both the transmitter and receiver. These do not need to be done at the same time. 1. Unplug the device from its power source. 2. Press and hold the Link/Source (Tx) or Link/Output (Rx) Selection button on the front panel. 3.
COMPLIANCE STATEMENTS FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
WARRANTY 1 YEAR LIMITED WARRANTY The HD FLOW3 offers the highest quality components and technology available. The product is warranted to be free from defects in material and workmanship, given normal use and care, for 1 Year from the original purchase date with proof of purchase. Please retain a copy of your receipt as you will need this to obtain warranty work. We will repair or replace the product which fails as a result of such a defect during the warranty period.
Wireless Full HD Sender Receiver www.hdflow.co.kr I DO IT Co., Ltd. #637, Smart-Hub Industry-University Convergence Center, 237 Sangidaehak-ro, Siheung-si, Gyeonggi-do, Korea Tel : +82 (0)31 8041 1500 Fax : +82 (0)31 8041 1550 E-mail : sales@hdflow.com I DO IT France 6-8 Rue de la Closerie ZAC Du Clos Aux Pois 91090 LISSES Cedex FRANCE Tel : +33 (0)1 64 97 52 28 Fax : +33 (0)1 64 97 52 35 E-mail : sales@i-do-it.