UTP 1.0 INSTALLATION & VERIFICATION INSTRUCTIONS ©2017 I.D. Systems, Inc.
UTP 1.0 Installation & Verification Instructions Copyright © 2017 I.D. Systems, Incorporated. All Rights Reserved. The material contained in this document is protected by the copyright and trade secret laws of the United States and other countries. It may not be reproduced, distributed, or altered in any fashion by any entity (either internal or external to I.D.
UTP 1.0 Installation & Verification Instructions I.D. Systems www.id-systems.com/ Customer Support: 888-855-0913 I.D.
UTP 1.0 Installation & Verification Instructions Table of Contents 1. OVERVIEW .............................................................................................................................................. 4 2. UTP 1.0 COMPONENTS ............................................................................................................................ 4 3. REQUIRED TOOLS (NOT PROVIDED) ...................................................................................................
UTP 1.0 1. • Installation & Verification Instructions Overview This document details UTP 1.0 (remote vehicle monitoring and control hardware) installation and verification process. Failure to follow the installation and verification processes may result in improper device operation and/or payment dispute for installation services. Contact Avis Budget Group customer support at xxxxxxxxxx with any questions regarding installation and/or verification.
UTP 1.0 4. Installation & Verification Instructions Installation Steps NOTE: In all cases, safe location and secure mounting of the UTP 1.0 device is the installer’s primary concern. Installer is responsible for ensuring the UTP 1.0 device is safely and securely mounted and does not interfere with vehicle operation. 1) Locate the vehicle’s OBD-II port (usually located on the bottom left of the driver’s side dash).
UTP 1.0 3) Installation & Verification Instructions Make sure the OBD-II connector latch is in the “open” position, then plug OBD-II connector into the vehicle OBD-II port. Make sure the connector is seated all the way down. After plugging it in, move the latch back to the closed position. Connector Latch Open Connector Latch Closed UTP 1.0 plugged into OBD-II port I.D.
UTP 1.0 Installation & Verification Instructions 4) If the vehicle alarm should sound during installation, use the key fob to unlock the doors and disable the alarm. 5) Once the UTP 1.0 connector is plugged in, the green LED light on the connector will begin to flash. It will take approximately 3.5 minutes to in-fleet successfully. (See LED Indicators for more information.) • LED Pattern: Quick blink for 3 minutes, then periodic flashing for 30 seconds before the LED turns solid green.
UTP 1.0 Installation & Verification Instructions Do not install near brake / gas pedal area 7) When tie wrapping the UTP 1.0 to the vehicle harness, wire tie both sides of the UTP 1.0 enclosure. Location of tie-wrap insert on enclosure Tie wraps fed through inserts on both ends of UTP 1.0 I.D.
UTP 1.0 Installation & Verification Instructions UTP 1.0 mounting feature and secured to vehicle harness UTP 1.0 securely tie wrapped onto wire harness. In this example, one side of the UTP 1.0 is tie wrapped and UTP cable is tie wrapped onto the wire harness as well. I.D.
UTP 1.0 8) Installation & Verification Instructions Final Install Validation: Make sure the UTP 1.0 enclosure is tucked in behind the panel and not visible to the customer. Double check to make sure the UTP 1.0 is tie wrapped securely to a wire harness and away from the gas/brake pedal area. UTP 1.0 installed on 2017 Ford Fusion. UTP is routed and tie wrapped onto a wire harness behind the panel. I.D.
UTP 1.0 5. Installation & Verification Instructions LED Indicators GREEN LED RED LED Fast blink = firmware download Fast blink = non-certified vehicle Slow blink = installing Slow blink = no cellular Solid on = install successful Solid on = install failure If both LEDs are… OFF after install = Normal OFF at install = No power ON = Fatal exception I.D.
UTP 1.0 6. Installation & Verification Instructions Installing on Multiple Vehicles at the Same Time The following process is recommended to speed the overall installation when installing UTP 1.0 devices on multiple vehicles at the same time. 1) 2) 3) 4) 5) 6) Arrange up to 10 cars side-by-side with enough room to open driver-side doors without hitting the adjacent vehicle. Starting with the first vehicle: • Turn vehicle ignition on, roll down driver-side window, and leave driver door open.
UTP 1.0 7. Installation & Verification Instructions Uninstalling the UTP 1.0 To safely uninstall the UTP 1.0, follow these steps: 1) Use the built-in tie wrap cutting feature on both side of the UTP 1.0 when cutting/removing tie wraps, so as not to damage the wire harness or the UTP 1.0 enclosure. See photos below. Carefully cut tie wrap without damaging harness or the UTP 1.0 enclosure I.D.
UTP 1.0 2) 3) Installation & Verification Instructions Move the OBD-II connector latch to the open position and unplug the OBD-II connector from the vehicle OBD-II port. Coil the UTP 1.0 cable, securing it to the enclosure, and fasten the OBD-II connector onto the receptacle on the enclosure. Move the latch to the closed position. Coil the cable, securing it to the enclosure Fasten OBDII connector to enclosure 4) Stack UTP 1.0 devices (as pictured below). I.D.