NEXT Type No. C19F06110 ImageQuest F910 Pefect Flat Monitor User’ Guide www.imageQuest.co.
BACK U.S.A. U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT INFORMATION TO THE USER NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BACK DECLARATION OF CONFORMITY WE HYUNDAI ELECTRONICS INDUSTRIES CO., LTD.
BACK F 910 Perfectly Flat 3D Monitor NEXT Contents 1. Introduction ...............................1/20 2. Safety Information ...................1/20 3. Installing the monitor ..............3/20 3-1. Packing List ....................................3/20 3-2. Fastening the swivel and tilt base ...4/20 3-3. Selecting a suitable location .........4/20 3-4. Connecting the monitor ................5/20 3-5. Setting the refresh rate.................8/20 Preset Timing Table.......................8/20 4.
F 910 BACK Perfectly Flat 3D Monitor NEXT 1. Introduction This manual contains instructions for installing and operating Hyundai DeluxScan F910. Hyundai DeluxScan F910 is a highly ergonomic color display unit; 2. Safety Information • • • • • • • 19” diagonal Flat 0.
F 910 Perfectly Flat 3D Monitor BACK NEXT Cleaning and Maintenance • • • • • • To avoid risk of electric shock, do not disassemble the display unit cabinet. The unit is not user-serviceable. Remember to unplug the display unit from the power outlet before cleaning. Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do not use thinner or benzene, abrasive cleaners or compressed air. Do not wipe the screen with a cloth or sponge that could scratch the surface.
F 910 BACK Perfectly Flat 3D Monitor 3. Installing the monitor NEXT The following items should be found in the packaging. 3-1. Packing List Monitor UK Japan America/Canada Europe South Africa Australia 3D Glasses(Optional) Tilt and Swivel Compact Disk ! Korea Signal Cable Power cord Above power cord can be changed upon different voltage areas. Please contact your dealer if anything is missing or damaged.
F 910 Perfectly Flat 3D Monitor BACK NEXT 3-2. Fastening the swivel and tilt base • Place the base against the bottom of the monitor so that the base fasteners are aligned with appropriate slots. Push the base towards the front of the monitor until the latch locks into position. • 3-3. Selecting a suitable location • Place the monitor at least 30cm from other electrical or heat-emitting equipment and allow at least 10cm on each side for ventilation.
F 910 BACK Perfectly Flat 3D Monitor 3-4. Connecting the monitor ! NEXT Before you start cabling your monitor, check that the power is off on all units. To avoid any possibility of electric shock, always connect your equipment to properly earthed outlets.
F 910 BACK Perfectly Flat 3D Monitor NEXT WORK STATION 3D Glasses Input (PlayerA, Player2) 6/20
F 910 BACK Perfectly Flat 3D Monitor 1. 2. 3. 4. Insert the 15-pin signal cable connector to the VGA connection on your computer and screw it down. (BNC OPTION : For BNC user, insert BNC connectors into the BNC connection on the monitor and PC) Plug the display unit’s power cable first to the back of the display unit. Then plug the power cable to a 100V - 240V earthed electrical outlet or to the system unit, if it has an outlet for the display power cable.
F 910 BACK Perfectly Flat 3D Monitor 3-5. Setting the refresh rate Follow the instructions below to set your refresh rate in Windows 98. 1. 2. 3. 4. 5. 6. Preset Timing Table NEXT Go to the configuration window (Start-Settings-Configuration window). Double click on the ‘Display’ icon. Click on the ‘Settings’ tab. Click on the ‘Advanced’ button. Click on ‘Adapter’ and select 85Hz from the list. Click on ‘Apply’ to accept the selected value.
F 910 BACK Perfectly Flat 3D Monitor 4. Adjusting the picture NEXT You can adjust the screen display by using the buttons located below the screen.
F 910 Perfectly Flat 3D Monitor 4-1. Using the On Screen Display 1. 2. 3. 4. 5. 6. BACK NEXT Push the MENU button to call the OSD to the screen. The resolution and frequency are displayed at the top of the menu box for your information. Push the or button to choose the item you want to adjust. The selected item is highlighted. Push the SELECT button to adjust the highlighted item. Use the or button to adjust the selection. Push the SELECT button to return to the previous menu if you are in a submenu.
F 910 BACK Perfectly Flat 3D Monitor NEXT 4-3. OSD Adjustments The OSD adjustments available to you are listed below. You can play the movie file to see how to adjust the picture image by clicking each icon or title hereunder. H. SIZE Adjusts the horizontal size of the entire screen image. H. POSITION Adjusts the horizontal position of the entire screen image. V. SIZE Adjusts the vertical size of the entire screen image. V. POSITION Adjusts the vertical position of the entire screen image.
F 910 BACK Perfectly Flat 3D Monitor NEXT PIN BALANCE If the sides of the picture are bowed to the right or to the left, you can correct the pincushion balance by using this adjustment. V. MOIRE Clears vertical moire if a series of concentric circles or arcs appear on your screen. H. MOIRE Clears horizontal moire if a series of concentric circles or arcs appear on your screen. Moire is an interference pattern that makes the screen seem to have faint lines.
BACK F 910 Perfectly Flat 3D Monitor NEXT H. LINEARITY If either left or right side of the picture is out of proportion to the other, you can correct horizontal linearity by using this adjustment. V. LINEARITY If top and bottom side of the picture is out of proportion to the center area, you can correct vertical linearity by using this adjustment. LANGUAGE You can select the language in which adjustment menus are displayed.
F 910 BACK Perfectly Flat 3D Monitor NEXT COLOR CONTROL Color temperature affects the tint of the image. With lower color temperatures the image turns reddish and with higher temperatures bluish. There are three color settings available: 9300K, 6500K or USER. With the USER setting you can set individual values for red, green and blue.
F 910 BACK Perfectly Flat 3D Monitor NEXT If you have tilted, swiveled or moved the display unit, you can perform demagnetization. During this process the picture is distorted for a few seconds. After demagnetizing, the color impurities have disappeared if caused by stray magnetic fields. Do not use the degauss feature more than once every half hour. CONTRAST Adjusts the contrast of the screen. BRIGHTNESS Adjusts the brightness of the screen. FLIPPING / INTERLACE .
F 910 BACK Perfectly Flat 3D Monitor 5. Display power management Reducing power consumption NEXT If the power management function of your computer is enabled, your monitor turns on and off automatically. You can control power management features from your computer. Your computer may have power management features which enable the computer or monitor to enter a power saving mode when the system is idle. You can reactivate the system by pressing any key or moving the mouse.
F 910 BACK Perfectly Flat 3D Monitor NEXT 6. Troubleshooting If your monitor is not functioning properly, you may be able to solve the problem by reading followings. Problem Blank screen Possible solution If the power LED is not lit, push the Soft power switch or Power switch(option) to turn the monitor on. If the display unit is powered through the computer, check that the computer is switched on. The display unit might be in standby mode. Push one of the keyboard keys.
F 910 BACK Perfectly Flat 3D Monitor NEXT Problem Possible solution The display does not enter power management mode The video signal from the computer does not comply with VESA DPMS standard. Either the computer or the graphics adapter is not using the VESA DPMS power management function. Screen flickers The screen may seem to flicker when the refresh rate is less than 75Hz. See the list of recommended modes in the section Preset timing table.
F 910 BACK Perfectly Flat 3D Monitor Problem Possible solution Windows Plug and Play does not recognize the monitor If your computer is DDC compatible, the display type is automatically correct. If, however, you need to change the display type, you will find the display units listed under Hyundai Electronics in the manufacture’s list. NEXT Contacting service If the above troubleshooting hints do not help you find a solution to the problem, contact an authorized service agent.
F 910 BACK Perfectly Flat 3D Monitor 7. Specifications 19"(viewable size : 18") Dot pitch 0.25 mm Picture tube Anti-Static, Medium-short. Display area factory preset area : 352X264 mm Number of color Infinite Input signals R.G.B Analog, 15 pin D-sub Frequency rate Horizontal : 30 to 107kHz, Vertical : 50 to 150Hz Maximum bandwidth 261 MHz Maximum resolution 1600X1200@85Hz Input voltage 100-240 VAC, 2.
