User’s Manual HYUNDAI DIGITAL TECHNOLOGY Co.,LTD. Home Page : www.hdt.co.kr URL : www.hdt-europe.eu Service e-mail : service@hdt-europe.
Contents 1. Introduction 1. Introduction 1.1. Overview ……………………………………………………………………… 4 1.2. Main Features ………………………………………………………………… 4 2. Safety/Precautions 2.1. Safety …………………………………………………………………………… 6 2.2. Precautions …………………………………………………………………… 8 3. Check Point before Use 3.1. Accessories …………………………………………………………………… 9 4. Controls/Functions 4.1 Front Panel …………………………………………………………………… 10 4.2 Remote Control ……………………………………………………………… 11 4.2.1Using the Remote Control …………………………………………… 12 5.
2. Safety/Precautions. 2.1 Safety Be sure to read the user’s manual before starting the operation of the unit. Do not touch the power cord with wet hands as it may cause electric shock. Never open the cover. It is very dangerous to touch the inside of the unit due to possible electric shock. Place the unit in a well ventilated and no-heat environment. When you do not use this unit for a long time, make sure that power cord is pulled out from the outlet.
2.2 Precautions When installing the unit Install the unit horizontally. An uneven installation may cause the unit to be damaged. Do not put heavy items such as a TV on the unit. That may cause the unit to be damaged. Do not leave the unit where the water drops or splashs. Do not put water holding items such as vase on the unit. Do not install the unit: - Where it is subject to vibrations - Where it is exposed to direct sunlight - Where there is humidity - Where the temperature is too high or too low.
4.2 RF Remote Control Unit. 4. Controls/Functions 4.1 Front Panel 1 2 8 3 4 5 6 7 9 [1] Antenna : Digital cable signal input to digital tuner [2] Switch Bypass : To switch the receiver in “Car SW mode” or “power on mode”. [3] PWR IN : Input Voltage level (10-28VDC). [4] SIM slot(Smart Card) : SIM Card slot.. [5] Ext IR : To receive the infrared signal from IR RCU (If want to be use the IR RCU). [6] USB HOST 2.
4.2.1. Using the Remote Controller Batteries How to insert a battery 1) Open the cover at the top of the near side of the remote control. 2) Insert a CR2025 type battery to be aligned with appropriate +/- polarity. 3) Close the cover completely. 5. How to Connect 5.1. When connecting IRD to Car TV with AV connectors When to replace a battery If the operational range of remote control is getting smaller, it indicates batteries are almost consumed. Replace the battery.
6.1.1Video Channels 6. Operation The STB has the following EPG Menu Structure: Add in the Correct Menu Structure from The Storybaod when the Updated Storyboard is Released. When the STB is powered ON the STB will automatically tune to the last viewed Channel. When the user presses the “TV” button on the Remote Control Unit the “Home” Screen is displayed. The Home Screen is the highest level menu screen. The Home Screen will display the currently tuned to event in the bottom left hand corner. 6.
When the user finds a current event they wish to view the user will press the “OK” button on the Remote Control Unit and the STB will display Full Video of the selected event as well as display a Program Banner over the video. 6.1.2 Radio Channels To view which Radio events are currently being broadcast the user follows the menu structure, Home-What’s On-Radio Channels. The Program Banner displays the following information: a. Date-MM/DD/YY Format. b. Current Time = 10:17 c. Channel Number = 300 d.
Notes; 1. When the Radio Channel is tuned to the Blue background screen is displayed with the Program Banner . The program banner contains the following information: a. Date-MM/DD/YY Format. b. Current Time = 16:11. c. Channel Number = 924. d. Channel Name = Radio 4 Digital. e. US TV Rating or MPAA Rating = NR. f. Sub Rating = D. g. Received Signal Strength Indicator ? shown as vertical bars with numeric value = 155. h. Current Event Name = The Archers. i. Current Event Start Time = 15:50. j.
6.1.4 Favourites To view which Channels the user has added to their favourites list and to see what Current and Future Events are being broadcast on the favourite channels the user follows the menu structure, Home-What’s On-Favourites. Notes; 1. To delete a Channel from the Favourite the user can pres the Red button on the Remote Control Unit.
6.2 Settings 6.2.1 Parental Control The Settings screen is the second level in the Home screen. There are 3 sub menu screens of Settings. These are: a. Parental Control. b. User Setup. c. System Setup. Parental Control allows Parents to control the content that can be viewed and the content that can be blocked. A Parent can control what content can be viewed and what content can be blocked by 3 methods: The Parental Control and System Setup screen are each protected by a 4 digit PIN.
6.2.1.1 Channel Block 6.2.1.2 Set Ratings The Channel Block screen lists all Video and Radio channels that are available to the user. To block channels the user scrolls through the channels. When the user highlights a channel that they wish to block they press the “OK” button on the Remote Control Unit. A X will appear next to the channel. This channel is now blocked. The user is not limited to the number of channels that they block.
6.2.1.3 Change Menu PIN 6.2.2 User Setup To change the 4 digit PIN that is used to access the Parental Control screen the user can select the Change Menu PIN sub menu. The user set up menu allows the user to modify the settings for the Set Top Box. Once the user has selected the Change Menu PIN option the user will need to enter the current PIN, the new PIN and then will need to confirm the New PIN. The user can then press the Blue button on the Remote Control Unit to save the changes.
6.2.2.2 Language Setup 6.2.2.3 Audio The user can change the EPG Text Language, the Audio Language and the Closed Captioning language from English to Spanish. To do this the user selects the Language Setup sub menu. The user can change audio settings of the Set Top Box by selecting the Audio sub menu. The user can then scroll through the fields and change the setting by pressing the Right/Left arrow key on the Remote Control Unit. Preferred Audio allows the user to select......
6.2.2.4 Notifications 6.2.2.5 Screensaver Setup The user can configure the notifications that appear on the screen as well as the duration of how long the notifications are displayed for by choosing the Notifications sub menu. The user can configure the Screensaver setup by selecting the Screensaver setup sub menu. The user can configure the period of time before a screen saver is displayed.
6.2.3 System Setup 6.2.3.1 Satellite Setup The System Setup menu is PIN protected and allows the user to change the tuning parameters of the Set Top Box if the Set Top Box is not able to achieve Signal Lock and the TV Setup. In the unlikely event that the Set Top Box can not receive a satellite signal the user can call Technical Support on 1-866-800-9030 can go to the AT&T website: http://www.cruisecast.
When the user has made the changes that the technical support representative has asked for then the user presses the “OK” button on the Remote Control Unit. After pressing the “OK” button on the Remote Control Unit the user will be presented with a Signal Lock screen. 6.2.3.2 TV Setup The user can change the TV display by selecting the TV Setup sub menu by highlighting the TV Setup sub menu and pressing “OK” on the Remote Control Unit. THIS SCREEN IS NOT UP TO DATE.
6.3 List Of Channels The List Of Channels is the third level menu in the Home Screen. In this menu all Video and Radio channels are listed together. There is no: a. Date. b. Current Time. c. Channel Number. d. Channel Name. e. Event Name. f. Event Start Time. g. Event Finish Time. h. US TV Rating or MPAA Rating-In this case TV Y7. i. Short Description of the highlighted Event. j. Received Signal Strength Indicator.
7. Trouble Shooting 8. Specifications This information will help you quickly solve the problem. If you are unable to solve the problem, contact your service provider. (Therefore, if the unit does not work properly, check it according to the procedures shown in the table below) Problem Possible causes Remedy LED on front panel DC power disconnected. Check the power cable and does not light and bypass switch. display No Picture or Wrong connection of the Connect two terminals sound.
Category USB Functional Speed Port Specification USB2.