DS-6210VC4 Base Station Owner's Manual Version: V00 Release Date: July 29th, 2011
Copyright Information Hytera is the trademark or registered trademark of Hytera Communications Co., Ltd. (the Company) in PRC and/or other countries or areas. The Company retains the ownership of its trademarks and product names. All other trademarks and/or product names that may be used in this manual are properties of their respective owners. The product described in this manual may include the Company’s computer programs stored in memory or other media.
DS-6210VC4 Base Station Owner's Manual Contents Contents Preface ....................................................................................................................................................1 1. Checking Items in the Package .........................................................................................................2 2. Product Controls ................................................................................................................................3 2.
DS-6210VC4 Base Station Owner's Manual Contents 2.8 Combiner (COM)...........................................................................................................................22 2.8.1 Function ..............................................................................................................................23 2.8.2 Rear Panel..........................................................................................................................23 3. Installation .................
DS-6210VC4 Base Station Owner's Manual Contents 6.2 Tasks ............................................................................................................................................42 A Abbreviations....................................................................................................................................
DS-6210VC4 Base Station Owner's Manual Figures Figures Figure 2-1 Components of Base Station Interface Unit .....................................................................3 Figure 2-2 Antenna Connector ..........................................................................................................4 Figure 2-3 Extended Interface Board ................................................................................................4 Figure 2-4 Components of Power Supply Module ..............
DS-6210VC4 Base Station Owner's Manual Figures Figure 3-5 Layout of holes for Combined Cabinet ...........................................................................31 Figure 3-6 Tighten the Bolt..............................................................................................................32 Figure 3-7 Layout of Modules in the Cabinet...................................................................................32 Figure 3-8 Opening the Cabinet Door ................................
DS-6210VC4 Base Station Owner's Manual Tables Tables Figure 1-1 Packing List......................................................................................................................2 Table 2-1 Descriptions on CHU Front Panel .....................................................................................7 Table 2-2 Descriptions on CHU Indicators ........................................................................................8 Table 2-3 Descriptions on BSCU Front Panel ...........
DS-6210VC4 Base Station Owner's Manual Tables Table 3-7 Checklist of Environment on Site ....................................................................................39 Table 7-1 Troubleshooting ..............................................................................................................
DS-6210VC4 Base Station Owner's Manual Preface Preface This section describes the conventions and revision history of this document. Documentation Conventions Instructional Icons Icon Description Tip Indicates information that can help you make better use of your product. Note Indicates references that can further describe the related topics. Caution Indicates situations that could cause data loss or equipment damage. Warning Indicates situations that could cause minor personal injury.
DS-6210VC4 Base Station Owner's Manual Checking Items in the Package 1. Checking Items in the Package No. Item Qty.
DS-6210VC4 Base Station Owner's Manual Product Controls 2. Product Controls 2.1 Base Station Interface Unit The base station interface unit on top of the cabinet consists of the antenna connector, extended interface board and power supply module. See Figure 2-1. Figure 2-1 Components of Base Station Interface Unit 2.1.1 Antenna Connector The antenna connector is described in Figure 2-2.
DS-6210VC4 Base Station Owner's Manual 3 Product Controls 1 2 1 GPS Antenna Connector 2 RX Antenna Connector 3 TX Antenna Connector Figure 2-2 Antenna Connector 2.1.2 Extended Interface Board The extended interface board consists of core network interface, extended interface and monitor interface. See Figure 2-3. Figure 2-3 Extended Interface Board Core network interface The core network interface contains 4-path EI interface and 2-path Ethernet interface.
DS-6210VC4 Base Station Owner's Manual Product Controls 2.1.3 Power Supply Module The power supply module is described below. 5 1 2 4 3 1 Ground Row 2 Circuit Breaker 3 AC Input Terminal 4 Surge Protection Device 5 AC Output Terminal Figure 2-4 Components of Power Supply Module 2.2 Cartridge In accordance with the IEC60297 standard, the cartridge is 19 inches in width and 7U in height. Each cartridge can accommodate four CHUs, two BSCUs and two PSUs. See Figure 2-5.
DS-6210VC4 Base Station Owner's Manual TX Antenna Product Controls PA TX Excitation Unit Baseband Signal Processing Unit ICB Power RX Antenna 1 RX Antenna 2 RX Antenna 3 Diversity Receiver Figure 2-6 Logical Architecture of Channel Unit 2.3.1 Function The CHU processes and converts protocols for the physical layer and data link layer of the PDT air interface. Physically it consists of channel board, TX board and RX board.
DS-6210VC4 Base Station Owner's Manual Product Controls Figure 2-7 Front Panel of CHU No. Name Description 1 RXA Diversity RX antenna input. 2 RXB RX antenna input. 3 RXC Diversity RX antenna input. 4 LED panel LED indicator 5 RS232 For commissioning. 6 TX For transmitting. Table 2-1 Descriptions on CHU Front Panel 2.3.3 LED Indicator The CHU indicators are described in Table 2-2.
DS-6210VC4 Base Station Owner's Manual Name PWR RUN TX RX ALM Color Product Controls Status Description On Power supply is in good working condition. Off Power is failure. On CHU is communicating with BSCU normally. Green Green Flashing CHU is starting. Off CHU is repeating. On CHU is allocating channel. Off The TX channel is free. On Carrier signal is present. Off The RX channel is free. On The CHU is failure. Off The CHU works properly.
DS-6210VC4 Base Station Owner's Manual Product Controls 2.4.1 Function The BSCU is mainly in charge of managing the wireless link resources within the coverage, so as to allocate them to different calls. 2.4.2 Front Panel The front panel of BSCU is illustrated as follows. Figure 2-9 Front Panel of BSCU No. Name Qty. 1 SMA Interface 1 GPS signal input. 2 RST Key 1 BSCU reset. 3 4 Commissioning Interface LED Panel Description 1 Video graphics array. 4 USB. 1 RS232.
DS-6210VC4 Base Station Owner's Manual Product Controls 2.4.3 LED Indicator The BSCU indicators are described in Table 2-4. Name Color PWR Green Status On Power supply is in good working condition. Off Power is failure. Flashing rapidly Flashing RUN Green slowly ALM CHU1-4 Green BSCU operates in slave mode. The BSCU is starting. Off The BSCU does not work properly. Functions are disabled locally. On Functions are disabled via GPS. Off Functions are enabled via GPS.
DS-6210VC4 Base Station Owner's Manual Name Color Status Green properly. Flashing The BSCU links with the MCB properly. Flashing and MCB. BSCU and MCB. On The BSCU links with the LNA properly. Flashing Green Data is being transferred or received between BSCU The link is abnormal or not connected between Off LAN1-2 standby BSCU and active BSCU. standby BSCU and active BSCU.
DS-6210VC4 Base Station Owner's Manual No. 4 5 Product Controls Item Voltage output Description (for other power supply from the CHU ) Voltage output (for BSCU) LVCC(13.5V DC) BSC_V(13.2V DC) It is connected to 2 BSCUs and outputs three channel 6 I/O interface signals. The first two is used for resetting PSU, and the last for installation status of PSU. 7 It is connected to 2 BSCUs respectively, and outputs Monitor Interface two signals including RS485 and CAN-BUS.
DS-6210VC4 Base Station Owner's Manual No. Product Controls Name Qty. Description 1 LED Panel 1 LED indicator 2 ON/ OFF Switch 1 Power Switch Table 2-6 Descriptions on PSU Front Panel 2.4.7 LED Indicator The PSU indicators are described in Table 2-7. Name Color Status On ALM PWR1 PWR2 BSC Red Green Green Green Description Major alarm. Blinking per second Minor alarm. Off The PSU works properly. On Path 1 outputs normally. Flashing Path 1 outputs HVCC or LVCC alarm.
DS-6210VC4 Base Station Owner's Manual Product Controls voice and data interconnection, monitor interconnection, and I/O interconnection. 2.4.9 Front Side The front side of ICB is described below. Figure 2-11 ICB (front side) No. Name Qty. 1 CHU Interface 4 For signal from CHU to ICB. 2 For signal from BSCU to ICB. 2 For signal from PSU to ICB. 2 3 BSCU Interface PSU Interface Description Table 2-8 Description on ICB (front side) 2.4.10 Back Side The back side of ICB is described below.
DS-6210VC4 Base Station Owner's Manual Product Controls Figure 2-12 ICB (back side) No. Name Qty. Description 1 DC Power Inlet 1 DC power input: -48V(NA -48V NOW) 2 AC Power Inlet 1 AC power input: 110V/220V 3 EC Interface 2 For interconnecting two cartridges in the cabinet. For interconnecting two EC cartridges and four IRUs between 4 EIB Interface 6 two cabinets, and also working as the signal interface from EIB to ICB in the core network interface board.
DS-6210VC4 Base Station Owner's Manual No. Name Product Controls Qty. Description 7 Power Outlet 6 DC power (+13.2V) for BSCU, FAN and DIU. 8 DIP Switch 1 For setting the cartridge address. Table 2-9 Description on ICB Interfaces (Back Side) The settings of DIP switch are descried in Table 2-10. No. 4 3 2 1 1 X ON X ON 2 X ON X OFF 3 X OFF X ON 4 X OFF X OFF Description Remark Address for main chassis. Address for the first extended chassis.
DS-6210VC4 Base Station Owner's Manual Product Controls 2.5.2 LED Indicator The FAN indicators are described in Table 2-11. Name Color PWR Red 1 Green Status Description On Power supply is in good working condition. Off Power is failure. On FAN1 works properly. Off FAN1 is out of operation or not installed. Blinking per FAN1 does not work properly. second 2 Green On FAN2 works properly. Off FAN2 is out of operation or not installed. Blinking per FAN2 does not work properly.
DS-6210VC4 Base Station Owner's Manual No. Product Controls Name Qty. Description 1 RS485 Monitor Interface 2 2 CAN-BUS Monitor Interface 2 3 Power Inlet 2 For connecting ICB. 4 DIP Switch 1 For setting the fan address. For connecting ICB and DIU. Table 2-12 Descriptions on FAN Front Panel The settings of DIP switch are descried in Table 2-13. No.
DS-6210VC4 Base Station Owner's Manual Product Controls 2.6.2 Front Panel The front panel of DIU is illustrated as follows. Figure 2-16 Front Panel of DIU No. Name Qty. Description 1 RXA 8 Diversity RX antenna output. 2 RXB 8 RX antenna output. 3 RXC 8 Diversity RX antenna output. Table 2-14 Descriptions on DIU Front Panel 2.6.3 Rear Panel The real panel of DIU is described below. Figure 2-17 Rear Panel of DIU No. Name Qty.
DS-6210VC4 Base Station Owner's Manual No. 4 Name Product Controls Qty. PWR 5 Description 1 Power Inlet 1 For grounding 6 RXA 1 Diversity RX antenna A 7 RXB 1 Diversity RX antenna B 8 RXC 1 Diversity RX antenna C Table 2-15 Descriptions on DIU Rear Panel The setting of DIU address is specified in Table 2-16. No.
DS-6210VC4 Base Station Owner's Manual Product Controls 2.7.3 Rear Panel The real panel of router is described as follows. 3 7 4 12 5 1 6 8 2 9 10 11 Figure 2-19 Rear Panel of Router No. Name No. Name 1 SIC Slot 2 2 SIC Slot 1 3 Ground Port 4 Power Inlet 5 Power Switch 6 Ethernet Port (LAN0) 7 Ethernet Port (LAN1) 8 Configuration Port (CON) 9 Auxiliary Port (AUX) 10 USB Port 11 CF Card 12 L2 Switch Port (LAN2-LAN9) Table 2-17 Descriptions on Router Rear Panel 2.7.
DS-6210VC4 Base Station Owner's Manual Name Product Controls Color Status - Off The system does not work properly. On The ESM card works properly. Green Flash Slowly ESM LINK Description The router is starting. Yellow On The ESM card is failure. - Off The ESM card is not inserted. On The link is not connected. Off The link has been connected. - Flashing ACT Data is being transferred or received. Off No data is being transferred or received. On The CF card has been inserted.
DS-6210VC4 Base Station Owner's Manual Product Controls COM Output Cavity Resonator Cavity Resonator Cavity Resonator Cavity Resonator 50Ω 50Ω CHU1 50Ω CHU2 50Ω CHU3 50Ω CHU4 Figure 2-20 Logic Diagram of Four Combiners 2.8.1 Function The COM is used to integrate multiple carriers from the base station sub-system into one output port to transmit by an antenna. 2.8.2 Rear Panel The rear panel of combiner is described below. Figure 2-21 Rear Panel of Combiner No.
DS-6210VC4 Base Station Owner's Manual Installation 3. Installation 3.1 Cable Layout The cable layout of base station is shown Figure 3-1.
DS-6210VC4 Base Station Owner's Manual Installation 3.2 Safety Information To reduce the chance of accident, please read the safety precautions very carefully before installation, maintenance and operations. 3.2.1 Power Supply Danger: Some components of the power system carry hazardous voltage in operation. Direct contact or indirect contact through moist objects with these components will result in fatal injury. z Never wear conductive objects such as watches, bracelets, rings and etc during operation.
DS-6210VC4 Base Station Owner's Manual Installation 3.3 Installation Preparation 3.3.1 Technical Files The following table lists the files associated with hardware installation. File type File Name Provided by the R&D engineers or technical Network Planning Drawing Instructional file Description sales. for installation It is filled by the investigation engineer on Site Survey Report site.
DS-6210VC4 Base Station Owner's Manual Installation 3.4 Unpacking Inspection 3.4.1 Check before Unpacking After the equipment arrives at the installation site, you should: z Check against the packing list, including total amount, customer address, and etc. z Contact us in case of any mistake. z Check the packaging case is in good condition and not placed upside down. If the outer package is damaged seriously or soaked, please contact us immediately.
DS-6210VC4 Base Station Owner's Manual Installation Figure 3-2 Removing the Cover Step 3 Remove the cover. The wooden case may contain the carton or cabinet. As for the former, directly take out the carton from the wooden case and unpack as instructed in Step 6. As for the latter, proceed to the next steps. Caution: Pay attention to the nails on the cover, to avoid hand injuries. Step 4 Place the wooden case in an upright position.
DS-6210VC4 Base Station Owner's Manual Installation Step 5 Remove the foam plate. Step 6 Slide the cabinet out of the wooden case slowly. 3.4.3 Unpacking Cartons Tool Paper knife To open a carton, do as follows: Step 1 Check the type and quantity of articles inside the carton according to labels, and cut the straps along the seam of the carton cover by the paper knife. Caution: Use moderate force to avoid damaging the articles inside. Step 2 Remove the foam plates and articles. 3.4.
DS-6210VC4 Base Station Owner's Manual Installation Wheel Figure 3-4 Layout of holes for a Single Cabinet 30
DS-6210VC4 Base Station Owner's Manual Installation Wheel Figure 3-5 Layout of holes for Combined Cabinet 3.5.2 Installing the Cabinet To install the cabinet, do as follows: Step 1 Place the cabinet in the planned position. Fix the cabinet by tightening four bolts at the bottom of the cabinet, as shown in Figure 3-6. 1. Loosen the upper nut counter-clockwise by the spanner. 2. Loosen the lower nut counter-clockwise by the spanner and lift the cabinet to an appropriate height. 3.
DS-6210VC4 Base Station Owner's Manual Installation Figure 3-6 Tightening the Bolt 3.6 Installing Modules into the Cabinet 3.6.1 Module Layout The position of all modules to be installed is shown in Figure 3-7. Figure 3-7 of Module Layout 3.6.2 Installation Procedures Step 1 Open the front and back door, as shown in Figure 3-8. 1. Unlock and remove the key in case of the keyhole in a vertical position. 2. Firmly press PUSH until the door knob is bounced. 3. Turn the door knob to the right. 4.
DS-6210VC4 Base Station Owner's Manual Installation Figure 3-8 Opening the Cabinet Door Step 2 Disassemble the side doors as shown in Figure 3-9. 1. Remove the eight screws on the frame. 2. Press down on the two latches and pull out the side door outwards. Caution: Care shall be taken to avoid injuries upon pulling out the side door outwards.
DS-6210VC4 Base Station Owner's Manual Installation Figure 3-10 Loosening the Ejector 2. Slide the BSCU along the guide rails smoothly as shown in Figure 3-11(1). 3. Perform the step 1 in a reverse way to lock the two ejectors. 4. Tighten the two screws on the two ejectors and the board respectively as shown in Figure 3-11 (2). Note: Loosen the two ejectors and draw out the module in case of removing it during installation.
DS-6210VC4 Base Station Owner's Manual Installation Figure 3-12 Installing the FAN Figure 3-13 Removing the FAN Note: Pull the latch inwards and pull out the FAN in case of removing it during installation. See Figure 3-13. Step 5 Install the DIU as shown in Figure 3-14. 1. Slide the DIU along the guide rails. 2. Fasten all screws to fix the DIU. Fasten the Screw Figure 3-14 Installing the Divider Unit Step 6 Install the COM as shown in Figure 3-15. 1. Slide the COM along the guide rails. 2.
DS-6210VC4 Base Station Owner's Manual Installation Caution: Handle with care as the COM is heavy. Figure 3-15 Installing the Combiner Unit Step 7 Connect all cables as shown in Figure 3-16. Figure 3-16 Cable Diagram Step 8 Install the side doors. 1. Align the side door with the frame and firmly press the latch. 2. Fasten the eight screws. 3.7 Installing Cables 3.7.1 Equipment Status The equipment shall be in the following status before connecting cables: z The cabinet has been installed.
DS-6210VC4 Base Station Owner's Manual Installation 3.7.2 Cables Cables are described in Table 3-3 and their positions are shown in Figure 3-17. Installation positions are located on top of the cabinet. Name Base Color Station Ground Cable (40m) AC Power Cord (15m) RF pcs) Jumpers (3 Remark Yellowish 16 mm2, 49-core, and 450/750V green Subject to the actual needs.
DS-6210VC4 Base Station Owner's Manual Installation z All modules have been installed. z The external power has been installed and all cables have been connected. z All switches of the power distribution box are set to OFF. 3.8.2 Examining the Cabinet The following requirements shall be met after installation. No. Check Item 1 The position of the cabinet should conform to the design drawing. 2 All modules should be installed correctly. 3 All cables within the cabinet should be connected properly.
DS-6210VC4 Base Station Owner's Manual Installation 3.8.4 Power On and Examination Caution: First measure the resistance of all power connectors and ground connectors using the multimeter and check whether short circuit occurs. The procedures are described as follows: Step 1 Check the input voltage (220V) from the main power and whether the live line and null line connect correctly. Step 2 All switches of PSU are set to ON. Step 3 Check whether all modules are powered properly.
DS-6210VC4 Base Station Owner's Manual Basic Operations 4. Basic Operations 4.1 Powering on All switches of the PSU are set to ON. 4.2 Powering off All switches of the PSU are set to OFF.
DS-6210VC4 Base Station Owner's Manual Troubleshooting 5. Troubleshooting Phenomena The PWR LED does not light up. The ALM LED on the PSU glows red. The ALM LED on the CHU glows red. The ALM LED on the BSCU Solution Check the power supply. Disconnect the power and replace the PSU. Replace the CHU. Replace the BSCU. glows red.
DS-6210VC4 Base Station Owner's Manual Routine Maintenance 6. Routine Maintenance 6.1 Purpose Routine maintenance is to ensure stable and reliable operation of the equipment. It can help to know the operation status of the equipment, so as to detect the potential troubles and remove them on time. The routine maintenance should achieve the following objects: z Remove all potential troubles to keep the system work properly. z Ensure all performance and service specifications meet requirements.
DS-6210VC4 Base Station Owner's Manual Routine Maintenance A Abbreviations Abbr.
DS-6210VC4 Base Station Owner's Manual Routine Maintenance Abbr.
DS-6210VC4 Base Station Owner's Manual Routine Maintenance Abbr. VGA Full Name Video Graphics Array FCC Warning: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.