User manual HYPRO WATER This product may be covered by one or more of the following U.S. patents: US10,377,644 B2. EN | 09.
Document information Safety information D WARNING! Information with the word WARNING warns of a dangerous situation that can lead to death or serious injuries. D CAUTION! Information with the word CAUTION warns of a situation that can lead to minor or moderate injuries. D ATTENTION! Information with the word ATTENTION warns of a situation that can lead to damage to property or the environment. 2 HYPRO WATER – 09.
Table of contents 1. 1.1 1.2 1.3 Safety information. . . . . . . . . . . . . . 4 Intended use . . . . . . . . . . . 4 Users . . . . . . . . . . . . . . . 4 General safety information . . . . 5 2. 2.1 2.2 2.3 2.4 2.5 Product information. . . . . . . . . . . . . 7 Functional principle . . . . . . . . 7 Product overview . . . . . . . . . 7 Scope of supply . . . . . . . . . . 9 Technical data . . . . . . . . . . 10 HYPRO app . . . . . .
1. Safety information 1.1 Intended use The device is used for filtering and disinfecting drinking water. The device is suitable for private or minor commercial use. Assembly can take place in combination with a 3-way water tap or an additional water tap. The device is only intended for use with cold water. ➡ “2.4 Technical data” (page 10). The flowing water must originate from a public supply. Rainwater cisterns, ponds, etc. are not suitable. The device is not suitable for continuous operation.
1.3 General safety information D WARNING! Danger due to a disregard of the user manual! This user manual contains important information for safe handling of the device. Possible dangers are noted separately. Failure to observe the information can lead to injuries. y Read the user manual through carefully. y Store the user manual in an accessible location. y Observe the safety information in this user manual. y y Store the film and other parts of the packaging out of the reach of children.
Used hoses must not be reused. Spent adsorption media will not be regenerated and used. In the following instances, use of the device is prohibited: – If the device or individual components are damaged. – In case of unauthorised modifications or changes to the device. – In case of device malfunctions. The manufacturer shall accept no liability for damages in the following cases: – With a failure to observe this user manual. – With non-intended use. – With incorrect handling.
2. Product information 2.1 Functional principle The device filters and disinfects tap water. An active carbon filter removes harmful substances. The UV light from the UV LEDs destroys pathogens. The drinking water is taken off: – Via the third setting with the use of a 3-way water tap. – Via the additional water tap. The device disinfects itself regularly by switching on the UV LEDs briefly. 2.2 Product overview 2.
2.2 / 2 2.2 / 3 H G1 I J K 8 G3 The LED display signals the operating statuses of the device to the user. G1 LED lights up green: The device is ready. G1 LED lights up blue: The device is disinfecting. The LED flashes yellow: G2 The device is ready for WLAN connection. L H Type plate I Mains cable with plug J Thread for mounting on the wall bracket K Water inlet L Water outlet G2 LED lights up yellow continuously: G2 The device is connected with the WLAN.
2.3 Scope of supply 2.3 / 1 A B A HYPRO WATER device B Filter C Wall bracket D Angled piece (5/16") E Angled piece (3/8") F Reducer piece G Connection piece (water tap 5/16") H Connection piece (water tap 3/8") I Water inlet hose (5/16") J Water outlet hose (3/8") K T-piece including shut-off valve L 4 safety clips (5/16") M 4 safety clips (3/8") N 4 screws for mounting on chipboard O Knurled screw P User manual C D E F G H I J K 9 L M N O HYPRO WATER – 09.
2.4 2.5 Technical data 110 - 240 VAC/ Connection voltage 41 W/ 50 - 60 Hz Water throughput* ≤ 3 l/min Water temperature min. 5 °C/ max. 30 °C Ambient temperature min. 5 °C/ max. 35 °C Operating pressure min. 2 bar/200 kPa max. 4 bar/400 kPa Protection class IP x1 Width 249.5 mm Depth 161 mm Height 209.3 mm Net weight 4.6 kg Weight with water 5.5 kg Filter capacity 2000 l Filter change 4 months WLAN WLAN 802.
3. Assembly 3.1 Requirements applicable to the installation site – The installation site must be clean and dry. – A suitable socket must be available at the installation site. The socket must be set up by a qualified electrician. The power connections must comply with the local regulations. The mains power supply must concur with the voltage specifications on the type plate. ➡ “2.4 Technical data” (page 10).
3.2 Unpacking the device D ATTENTION! Danger of damage due to incorrect handling! The device and its surfaces may be damaged during unpacking or transport. y Do not cut into the protective cardboard box. y Keep objects that may scratch the device away from it. y y y Unpack the device and all enclosed parts carefully. Check the device and all enclosed parts for damage. Check that the scope of supply is complete. ➡ “2.3 Scope of supply” (page 9). 3.
3.3 / 1 3.4 Performing assembly This user manual contains an example illustration of the device: – With connection to a 3-way water tap. – With assembly beneath the worktop. 3.4 / 1 y Assemble all of the required tools and materials: – Bucket – Cutter knife – Pen – Spirit level – Screwdriver – Pipe wrench 20 cm 13 10 cm HYPRO WATER – 09.
D ATTENTION! 3.4 / 2 Danger of damage due to incorrect handling! The device and the environment can be damaged if a torque of 3 Nm is exceeded when screwing on the connections. y Tighten the connections with a maximum torque of 3 Nm. 3.4 / 4 y Shut off the angle valve on the cold water line. 3.4 / 3 y y y y y 14 Position a bucket beneath the angle valve on the cold water line. Unscrew the cold water connection to the water tap from the angle valve.
D WARNING! 3.4 / 5 Danger of explosion or electric shock! Drilling into gas, water or electrical lines can result in dangerous situations. y Make sure no lines are inside the wall at the fastening points. 3.4 / 6 y y y Select a suitable position for the wall bracket. ➡ “3.1 Requirements applicable to the installation site” (page 11). Straighten the wall bracket using the spirit level. Mark the four fastening points.
3.4 / 7 y y Insert the angle piece (5/16") in the water inlet (left) as far as it will go. Secure the angled piece (5/16”) with the safety clip (5/16"). 3.4 / 9 y y 3.4 / 8 y y 16 Insert the hose (5/16") in the angle piece (5/16") as far as it will go. Secure the hose (5/16”) with the safety clip (5/16"). Insert the angle piece (3/8") in the water outlet (right) as far as it will go. Secure the angled piece (3/8”) with the safety clip (3/8"). 3.
3.4 / 11 y y Guide the mains cable and hoses from the top through the cut-out into the wall bracket. Position the device on the wall bracket. 3.4 / 13 y Slide the reducer piece into the T-piece as far as it will go. 3.4 / 14 3.4 / 12 17 y y Screw the connection piece (water tap) onto the drinking water tap. Screw the knurled screw from below through the wall bracket into the device. HYPRO WATER – 09.
3.4 / 15 3.4 / 16 y y Insert the hose (5/16") in the reducer piece as far as it will go. Secure the hose (5/16”) with the safety clip (5/16"). 3.4 / 17 y y y Guide both hoses from the device to the connection piece and reducer piece respectively. Mark the respective hose lengths required. Shorten both hoses to the required lengths. Make sure the hoses are cut straight. y y 18 Insert the hose (3/8") in the connector (water tap) as far as it will go.
3.4 / 18 y Remove the device cover. To do so, push down on the pressure point and then grasp beneath the edge of the device cover. 3.4 / 20 y Unscrew the screw cap for the filter chamber. 3.4 / 21 3.4 / 19 19 y y Turn the shut-off valve in the “CLOSE” direction. HYPRO WATER – 09.2020 y y Remove the protective film from the filter. Insert the filter. During insertion, carefully press the filter down until it latches into the device.
3.4 / 22 3.5 Completing assembly 3.5 / 1 y Close the screw cap for the filter chamber until it reaches the end position. y Plug the mains plug into the socket. As soon as the power supply has been established, the device opens a hotspot for a period of fifteen minutes. The LED flashes yellow at this time. It is possible to connect the device with the WLAN with the help of the HYPRO app. When the device is connected to the WLAN, the LED continuously glows yellow.
3.5 / 2 y y Open the shut-off valve for the T-piece. Open the angle valve on the cold water line. 3.5 / 4 y Close the device cover. 3.5 / 3 21 y Turn the shut-off valve in the “OPEN” direction. HYPRO WATER – 09.
3.5 / 5 After assembly and first commissioning, check: y Perform a visual inspection for water escaping at the connection points. After fitting a new filter, light abrasion can result in small carbon particles in the water. The particles will not affect your health. y Open the drinking water tap and allow the water to run for approx. 60 seconds. y Allow the drinking water to flow until particle emission has subsided, although for a minimum of 60 seconds. 22 HYPRO WATER – 09.
4. Use D CAUTION! Adverse effect on the drinking water quality! If the device has been disconnected from the power supply for a number of days, the device is unable to perform selfcleaning. The quality of the drinking water may be adversely affected. y Allow the drinking water to run for 60 seconds before using it. Drawing off drinking water: y Draw off the filtered and disinfected drinking water as required. 4/1 G1 G2 G3 The LED display signals the operating statuses of the device to the user.
5. Cleaning Information on cleaning: y Clean the device surfaces with a nonlinting, lightly dampened cloth. y Wipe the device surfaces dry with a non-linting, dry cloth. 24 HYPRO WATER – 09.
6. Maintenance 6.1 Changing the filter 6.1 / 1 For the device to work optimally, the filter must be changed as soon as the following criteria are met: y Flow quantity of 2000 liters reached. y Operating period of 4 months reached. When the filter needs changing, the LED flashes red. When the HYPRO app is used, the user also receives notification when it is time to replace the filter. y y Remove the device cover. ➡ “3.4 / 18” (page 19). Turn the shut-off valve in the “CLOSE” direction.
6.1 / 2 6.2 y y y y y y y y y 26 Checks Make sure no water can penetrate at the power cable or power source. Draw the used filter out of the device at the handle and pick up any escaped water. Remove the protective film from the new filter. Insert the new filter. During insertion, carefully press the filter down until it latches into the device. ➡ “3.4 / 21” (page 19). Screw the screw cap for the filter chamber shut. ➡ “3.4 / 22” (page 20). Turn the shut-off valve in the “OPEN” direction. ➡ “3.
7. Trouble-shooting If an LED is flashing or illuminated, one or more faults are present. To allow better analysis of faults, we recommend installing the HYPRO APP. Possible faults are described as follows: Description of the fault. – Possible cause. y Remedy. The LED flashes red. – No filter in the device. y Insert an original filter. – Filter capacity depleted. y Change the filter. ➡ “6.1 Changing the filter” (page 25). LED lights up red continuously. – Fault in the device. y Pull the power plug.
If the fault persists: y Turn the shut-off valve in the “CLOSE” direction with the water tap open. ➡ “3.4 / 19” (page 19). y Turn the shut-off valve in the “OPEN” direction with the water tap open. ➡ “3.5 / 3” (page 21). Quantity drawn off < 3 l/min – Take-off quantity varies depending on the type of filter used. – Line pressure insufficient. y Contact your installation engineer. – Filter capacity depleted. y Change the filter. ➡ “6.1 Changing the filter” (page 25).
8. Disassembly Disassembly of the device after its service life: y Disconnect the mains plug from the socket. y Collect the escaped water in a bucket. y Turn off the angle valve on the cold water line. y Turn the shut-off valve in the “CLOSE” direction y Open the drinking water tap until no further water runs out. y Close the drinking water tap. y Draw out the reducer piece. y Unscrew the connection piece (water tap) from the drinking water tap. y Unscrew the knurled screw below the wall bracket.
9. Disposal 9.1 Disposing of the packaging 9.3 D ATTENTION! Danger of environmental damage due to incorrect disposal of the packaging! y Do not dispose of the packaging together with standard household waste. y Submit the packaging for environmentally-friendly and correct recycling (reuse). y Store the packaging out of the reach of children. The packaging materials are selected on the basis of environmentally-compatible aspects and are produced from recyclable materials.
10. Annex 10.1 Contact details for customer service If you have any questions or comments: Internet: www.hytecon.com Address: HYTECON Produktion and Vertrieb GmbH Oststraße 68 32051 Herford Germany Email: Telephone: 10.2 info@hytecon.com +49 5221 28400 - 0 Data protection Our data protection policy can be found at: www.hytecon.com 10.
10.4 FCC/ISED Notes This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Cet équipement est conforme aux limites d'exposition aux rayonnements RSS-102 établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. 33 HYPRO WATER – 09.
10.5 List of replacement parts Replacement parts can be ordered from customer service. ➡ “10.1 Contact details for customer service” (page 31). Replacement part Item No. Wall bracket 1000014 Hose set 1001 Device cover 1000012 Screw cap for the filter chamber 1000032 Filter 1000035 34 Illustration HYPRO WATER – 09.
10.6 CE declaration of conformity 35 HYPRO WATER – 09.
10.7 NSF performance data 36 HYPRO WATER – 09.
HYPRO WATER – 09.
HYPRO WATER – 09.
HYPRO WATER – 09.
09.