5600 Calendar Clock Valve Combination Organic Color Removal & Softener Operation Manual Read all instructions carefully before operation. #51426 Rev.
Performance and Specifications Item Number Model Number Softening Capacity (kilograins) @10lb/cf(1) 7377 WTCA45 12 Color Removal Service Maximum Capacity (ppm-gallons) Flow Rate(2) Flow to Drain (1) @10lb/cf USGPM (LPM) USGPM (LPM) 2,000 8 (30.3) 2.4 (9.1) Mineral Tank Size(3) inches (mm) Brine Tank Size(3) inches (mm) 10 x 54 (254 x 1372) 22 x 38 (559 x 965) Resin Volume cu.ft. (litres) Anion Resin Volume cu.ft. (litres) Salt Capacity Lbs. (kg) Shipping Weight Lbs. (kg) 0.50 (14) 1.
Installation Instructions CAUTION: If the ground from the electrical panel or breaker box to the water meter or underground copper pipe is tied to the copper water lines and these lines are cut during installation of the Noryl bypass valve and/or poly pipe, an approved grounding strap must be used between the two lines that have been cut in order to maintain continuity.
4. Attach the bypass valve to the control valve. Connect the inlet and outlet of the water softener to the plumbing in the house. The control valve must not be subjected to temperatures above 71°C (160°F). To avoid damaging the control valve when sweat fittings are used, solder the threaded copper adapters to the copper pipe and then, using teflon tape, screw the assembly into the bypass valve. CAUTION - do not use pipe thread compound as it may attack the material in the valve body. 5.
Operating Instructions Setting the Time of Day (Figure 3) This is a 24-hour timer and must correspond with the correct time on your wrist watch to ensure proper cycling of your conditioner. Disengage the drive gear by pressing and holding in the RED BUTTON on the left side of the control. Now turn the large 24-hour gear until the actual time of day is at the time of day arrow at the bottom of the panel. Release the red button to re-engage the drive gear.
Salt Settings are factory set and should not need adjustment WTCA45...................................8 lbs Automatic Bypass The regeneration cycle lasts approximately 2-1/2 hours, after which soft water service will be restored. During regeneration, hard water is automatically bypassed for use in the household. Hot water should be used as little as possible during this time to prevent hard water from filling the water heater.
Maintenance Checking the Salt Level Check the salt level monthly. Remove the lid from the cabinet or brine tank, make sure salt level is always above the brine level (you should not be able to see water). Adding Salt Use only clean salt labeled for water conditioner use, such as crystal, pellet, nugget, button or solar. The use of rock salt is discouraged because it contains insoluble silt and sand which build up in the brine tank and can cause problems with the system’s operation.
Trouble Shooting your Combination Softener Unit Problem: Fishy or unpleasant odour is apparent in the treated water that is not present in the untreated water. • This odour may be apparent on startup and will 1. pH of the incoming water may be high. typically be reduced or eliminated after a couple service runs and regenerations cycles of the Combination Softener unit. • The addition of chlorine along with high pH 2.
• As a last resort, try adding approximately four (4) 4. Cont’d... • ounces of household bleach (5.25%) into the brine well. Begin a manual regeneration. Monitor the drain line for a strong chlorine odour which should occur in the brine draw cycle . When odour is present, halt regeneration by unplugging unit and shutting down water flow to the unit via the bypass valve.
Problem: Combination Softener unit appear to be causing a high pressure drop in home water system. • Confirm pressure loss is due to the unit, and 1. Pressure drop may be due other factors. not the result of distribution or well pump problem. • Confirm pressure loss is due to unit by checking flow while in BYPASS mode. • Check that flow demand is not exceeding rated flow rate of Combination Softener unit.
GUARANTEE HYDROTECH guarantees that your new water conditioner is built of quality material and workmanship. When properly installed and maintained, it will give years of trouble-free service. FIVE YEAR COMPLETE PARTS GUARANTEE HYDROTECH will replace any part which fails within 60 months from date of manufacture, provided the failure is due to a defect in material or workmanship.