Operator′s manual Manuel d’utilisation Manual de instrucciones Saw attachment PA PA 1100 Accessoire de sciage PA PA 1100 Suplemento de sierra PA PA 1100 Eng lish GB FR ES
KEY TO SYMBOLS . Always wear approved protective gloves. Symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Wear sturdy, non-slip boots. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Other symbols/decals on the machine refer to special certification requirements for certain markets.
CONTENTS Contents KEY TO SYMBOLS Symbols ....................................................................... CONTENTS Contents ...................................................................... Note the following before starting: ................................ SAFETY INSTRUCTIONS Cutting equipment ........................................................ Specification of bar and saw chain .............................. Sharpening your chain and adjusting raker clearance . Tensioning the chain .....
SAFETY INSTRUCTIONS Cutting equipment ! This section describes how you can achieve maximum clearing capacity and extend the life of the cutting attachment through correct maintenance and using the right type of cutting attachment. Only use cutting equipment recommended by us! See the Technical data section. WARNING! Always stop the engine before doing any work on the cutting attachment. This continues to rotate even after the throttle has been released.
SAFETY INSTRUCTIONS Chain • • • 3 File position 4 Round file diameter 5 File depth Saw chain pitch (inches). (The distance between three drive links, divided by two.) Drive link width (mm/inches) 1 5 Number of drive links. It is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file gauge. This will help you obtain the maximum kickback reduction and cutting performance from your chain.
SAFETY INSTRUCTIONS • • Always file cutting teeth from the inside face outwards. Reduce the pressure on the return stroke. File all the teeth on one side of the bar first. Then turn the saw over and file the remaining teeth from the other side. Setting the raker clearance • Before setting the raker clearance the cutting teeth should be newly sharpened. We recommend that you adjust the raker clearance every third time you sharpen the chain.
SAFETY INSTRUCTIONS Filling with chain oil 1 Undo the bar nut. The oil pump is preset at the factory to meet most lubrication requirements. A full oil tank will last about half as long as a full tank of fuel. You should therefore check the level of oil in the oil tank regularly to avoid damage to the saw chain and bar that could occur due to lack of lubrication. 2 Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner.
SAFETY INSTRUCTIONS 2 Check that the oil channel in the gear housing is clean. Clean if necessary. 3 Check that the bar tip sprocket turns freely. If the chain lubrication system is still not working after carrying out the above checks you should contact your service workshop. Vibration damping system Check regularly that the vibration damping element is free from cracks. Check regularly the degree of wear to the rubber dampers. Replace them if worn.
SAFETY INSTRUCTIONS Personal protection • Always wear boots and other equipment described under the heading Personal protective equipment in the machine’s Operator’s Manual. • Always wear working clothes and heavy-duty long trousers. • Never wear loose clothing or jewellery. • Make sure your hair does not hang below shoulder level. Safety instructions regarding the surroundings • Never allow children to use the machine. • Ensure that no-one comes closer than 15 m while you are working.
SAFETY INSTRUCTIONS • Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. • Always work at full throttle. • Let the engine drop back to idle speed between each cut. Long periods at full throttle can cause serious damage to the centrifugal clutch. ! WARNING! Never stand directly underneath a branch that is being cut. This could lead to serious or even fatal personal injury.
WHAT IS WHAT? 9 11 11 2 1 3 8 6 10 5 4 7 12 15 13 14 What is what on the saw attachment? (Saw attachment with shaft PA 1100) 1 Bevel gear 9 2 Chain lubrication adjustment screw 10 Chain oil tank 3 Shaft (1100 mm) 11 Filling with chain oil 4 Harness support hook 12 Operator′s manual 5 Protective guard for saw chain 13 Transport guard 6 Bar nut 14 Combination spanner 7 Chain tensioning screw 15 Harness 8 Chain Bar English – 11
WHAT IS WHAT? 8 10 10 2 1 7 5 9 4 3 6 11 14 12 13 What is what on the saw attachment? (Saw attachment without shaft PA) 1 Bevel gear 8 Bar 2 Chain lubrication adjustment screw 9 Chain oil tank 3 Harness support hook 10 Filling with chain oil 4 Protective guard for saw chain 11 Operator′s manual 5 Bar nut 12 Transport guard 6 Chain tensioning screw 13 Combination spanner 7 Chain 14 Harness 12 – English
ASSEMBLY Fitting the cutting head Fitting the bar and chain (Saw attachment with shaft PA 1100) • Unscrew the bar nut and remove the protective cover. • Fit the bar over the bar bolt. Place the bar in its rearmost position. Place the chain over the drive sprocket and in the groove on the bar. Begin on the top side of the bar. • Make sure that the edges of the cutting links are facing forward on the top edge of the bar. • Fit the cover and locate the chain adjuster pin (A) in the hole in the bar.
ASSEMBLY Adjusting the harness Check before starting You should always use the harness with the machine to give maximum control over the machine and reduce the risk of fatigue in your arms and back. • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blunt, cracked or damaged equipment. • Put on the harness. • Hook the machine onto the harness support hook.
TECHNICAL DATA Technical data Saw attachment without shaft PA Saw attachment with shaft PA 1100 0,22 0,22 0,8 1,4 Equivalent noise pressure level at the user’s ear, measured according to EN ISO 11680-1, dB(A) 95 96 Equivalent noise power level at the user’s ear, measured according to EN/ISO 11680-1 and ISO 10884, dB(A) 106 106 Technical data Lubrication system Oil tank capacity, litre Weight Weight without fuel, cutting attachment and guard, kg Noise levels (see note 1) Vibration levels Vibration
TECHNICAL DATA EC-declaration of conformity (Applies to Europe only) We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declare that this saw attachment from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the type plate, with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVE: of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
20 1140248-26 ´®z+H8r¶0_¨ ´®z+H8r¶0_¨ 2004-02-05
