GB Operator’s manual Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Manual de ES instrucciones Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina. DE Bedienungsanweisung Lesen Sie die Bedienungsanweisung sorgfältig durch und machen Sie sich mit dem Inhalt vertraut, bevor Sie das Gerät benutzen.
KEY TO SYMBOLS Symbols on the machine: Symbols in the operator’s manual: WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear approved protective gloves.
CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ............................................. Symbols in the operator’s manual: ............................... CONTENTS Contents ...................................................................... WHAT IS WHAT? What is what on the stand? ......................................... SAFETY INSTRUCTIONS Steps before using a new stand ................................... Personal protective equipment .....................................
WHAT IS WHAT? 1 19 23 28 20 18 16 28 22 15 27 2 13 21 12 30 4 28 14 3 11 17 5 10 9 7 6 8 26 24 29 25 31 What is what on the stand? 1 Locking screw 17 Expansion attachment 2 Spirit level 18 Drill column 3 Locking screw, locking clamp 19 Stop washer 4 Feeder housing lock 20 Locking clamp for quick mounting 5 Locking screw drill column 21 Mounting for feed lever 6 Position ring 22 Clamping screws for glide plates 7 Locking screw, position ring 8 Adjustment screws 23 Qu
SAFETY INSTRUCTIONS Steps before using a new stand • Personal protective equipment Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. • This machine is designed for and intended for drilling concrete, brick and different stone materials. All other use is improper. • The machine is intended for use in industrial applications by experienced operators. • Keep the workplace tidy. Disorder leads to accident risks.
SAFETY INSTRUCTIONS General safety precautions • General working instructions Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. ! WARNING! There is always a risk of crush injuries when working with products containing moving parts. Wear protective gloves to avoid body injuries.
PRESENTATION Stand DS50 and DS70 It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator′s manual as a valuable document. By following its′ content (using, service, maintenance etc) the life span and the second-hand value of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator′s manual. • The feeder housing's transmission is adjustable. The higher gives 2.
PRESENTATION Accessories • Water collector • Quick mounting for automatic feed unit (both sides of feeder housing) • Retaining ring • Expander • Distance • Stabilizer For extra support.
ASSEMBLY Assembling the stand 1 2 • Drill holes (15 mm) in the floor or in the wall and knock in the expander bolts. Assembly of drill motor 1 Lock the feeder housing on the drill column with the lock handle. 2 Loosen the locking screw for the locking clamp. 3 Always remove the drill bit before the motor is mounted or dismounted. 4 Mount suitable drilling machine on the quick mounting. Mount the quick mounting and drilling machine in the track on the locking clamp.
ASSEMBLY Before drilling ! ! WARNING! Before drilling, check that all locking screws are tightened well. Serious accidents can occur if the concrete core remains in the drill when backing out the drill motor/drill from the floor, wall or ceiling. WARNING! If the vacuum plate is used, make sure the support surface is not porous and can loosen from the floor or the wall. Make sure that the vacuum pump has sufficient power to secure the vacuum plate. The vacuum plate must never be used for ceiling drilling.
MAINTENANCE Stand maintenance 3 Loosen the adjustment screws. 4 Loosen 2*4 clamping screws for the glide plates. 5 Remove the glide plates. 6 Lay down the stand. 7 Mount a new lower glide plate on the column. Fit the feeder housing on the column and fasten the lower glide plate on the feeder housing. Mount a new upper glide plate on the column. Fasten the upper glide plate on the feeder housing.
TECHNICAL DATA Dimensions DS50 DS70 DS50 ATS 7 8 6 9 5 1 3 10 2 4 DS50, mm/inch DS70, mm/inch 1 438/17,2 438/17,2 2 320/12,6 340/13,4 3 526/20,7 546/21,5 4 235/9,3 265/10,4 5 971/38,2 1026/40,4 6 1140/44,9 1205/47,4 7 177/7,0 - 8 231/9,1 - 9 1158/45,6 - 10 450/17,7 - Stroke , mm/inch --------------------- Expander ------------- Max.
TECHNICAL DATA The column's angling 360° 5° 66, ° 90 Weight 1 8 2 3 7 4 5 6 DS50, kg/lbs DS70, kg/lbs 1 Drill column 6,7/14,7 9,1/20,0 2 Feeder housing 7,8/17,2 9,7/21,3 3 Quick mounting 0,6/1,3 0,6/1,3 4 Feed lever - 0,8/1,8 5 Feed lever 0,8/1,8 - 6 Base plate 9,2/20,2 12,0/26,4 7 Transport wheels 4,1/9,0 4,1/9,0 Total weight without stabilizer 29,2/64,2 36,3/79,9 Stabilizer 9,1/20,0 - 8 English – 13
TECHNICAL DATA EC-declaration of conformity (Applies to Europe only) Husqvarna Construction Products, SE-433 81 Partille, Sweden, tel: +46-31-949000, declares under sole responsibility that the stands Husqvarna DS50AT and DS70AT from 2007’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number) are in conformity with the requirements of the COUNCIL’S DIRECTIVES: - of June 22, 1998 ”relating to machinery” 98/37/EC, annex IIA.
www.husqvarnacp.