Specifications

ManualsBrandsHUSQVARNA ManualsElectronicsHMI board with Bluetooth functionality

Issued by: Therese Berg

Issued date: 200421

1 (8)

Instruction for implementing Bluetooth

functionality into robotic mower:

Certification Requirements

In addition to technical implementation specifications, the following instructions shall be

followed when implementing the HMI Boards incorporating Bluetooth functionality, i.e. the

HMI BLE1A and HMI BLE1B, for the below mentioned certifications to be valid.

These instructions are also applicable to the Application boards using the Bluetooth

design BLE1C.

These instructions shall be followed for all boards with the following Bluetooth design on

them:

• HQ-BLE-1: 590 54 13

The design is on all PCBs with any of the numbers:

• 582 87 12

• 590 11 35

• 591 10 05

Changes or modifications made to this equipment not expressly approved by Husqvarna

compliance department may void the validity of the certification, for instance the FCC

authorization to operate this equipment.

The Bluetooth boards with design HQ-BLE-1 can only be used in robotic lawn mowers

developed and manufactured by Husqvarna. The boards are only allowed to be mounted

during the manufacturing process of the robotic lawn mower. The boards are not for sale

for use in any other product. The boards are only allowed to be used in the robotic lawn

mower models which are covered by the certification.

1 Identification of the certified boards

Board

level

PCB: 582 87 12

PCB: 590 11 25

PCB: 591 10 05

Design

Common Robotic Mower BT design, inkl. Antenna.

Design reference: 590 54 13-01 (“HQ-BLE-1”)

Summary of content (8 pages)

PAGE 1
Issued by: Therese Berg Issued date: 200421 Instruction for implementing Bluetooth® functionality into robotic mower: Certification Requirements In addition to technical implementation specifications, the following instructions shall be followed when implementing the HMI Boards incorporating Bluetooth functionality, i.e. the HMI BLE1A and HMI BLE1B, for the below mentioned certifications to be valid. These instructions are also applicable to the Application boards using the Bluetooth design BLE1C.
PAGE 2
Issued by: Therese Berg Issued date: 200421 2 Worldwide 2.1 Bluetooth Special Interest Group For Bluetooth certification to BT SIG, the design HQ-BLE-1 is certified. All products that uses HMI-boards or other boards with Bluetooth functionality activated shall be listed in the BT SIG community database. The guidelines from Bluetooth SIG regarding word mark and logos shall be followed for documentation and information. 3 Europe 3.
PAGE 3
Issued by: Therese Berg Issued date: 200421 4.1 Robotic mower The ZASHQBLE-1A, -1B and -1C designs are certified as limited modular approvals due to the design without shielded RF-circuit. Therefore shall the radio characteristics be verified on the robotic lawn mower. This check can be done as a spot check with the mower in a typical configuration to verify fundamental frequency and spurious emissions according to applicable rules as mentioned above.
PAGE 4
Issued by: Therese Berg Issued date: 200421 Also the following notice should be on a label on the outside of the mower: NOTICE: This device complies with Part 15 of the FCC Rules and with Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: • • this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. 4.1.
PAGE 5
Issued by: Therese Berg Issued date: 200421 (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
PAGE 6
Issued by: Therese Berg Issued date: 200421 —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 5 RoW 5.1 Japan The design HQ-BLE-1 (590 54 13) is certified according to Japanese Radio, and may not be changed in any way. 5.1.
PAGE 7
Issued by: Therese Berg Issued date: 200421 For the Bluetooth module, the boxed R shall be followed by 202 and a certification specific number, which gives R 202-SMG024 as follows: R 202-SMG024 5.2 Brasil – Modular approval In Brasil is the Blutooth functionality planned to be certified under two licenses: • • HMI Board Type 10, 11 and 12 as a family with one certificate number, HMI Board Type 13 with one certificate number. 5.2.
PAGE 8
Issued by: Therese Berg Issued date: 200421 5.2.3 Manual In the manual there has to be a clear reference to the included radio module as a verbatime text. The text shall be: Este produto contém a placa HMI Board Type XX código de homologação ANATEL XXXXX-XX-XXXXX. It is not allowed to add multiple board type numbers or put the info in a table etc. If the manual covers more than one model (i.e.