US Operator’s manual Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. FR Manuel d’utilisation Lire attentivement et bien assimiler le manuel d’utilisation avant d’utiliser la machine. ES Manual de instrucciones Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina.
KEY TO SYMBOLS Symbols on the machine: Symbols in the operator’s manual: WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear approved protective gloves.
CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ............................................. Symbols in the operator’s manual: ............................... CONTENTS Contents ...................................................................... WHAT IS WHAT? What is what on the drilling machine? ......................... WHAT IS WHAT? What is what on the stand? ......................................... SAFETY INSTRUCTIONS Steps before using a new drilling machine ..................
WHAT IS WHAT? What is what on the drilling machine? 1 Switch 5 Gear selector 2 Carbon brush cover 6 Water connector 3 Fixing for stand 7 Operator’s manual 4 Drill spindle 4 – English
WHAT IS WHAT? What is what on the stand? 1 Jacking screw 12 Gear box 2 Drill column 13 Rack 3 Depth and tilt scale 14 Wheel set (removable) 4 Vertical and horizontal level indicator 15 Leveling adjustment screws 5 Feeder housing 16 Base plate with integrated vacuum function 6 Locking screw, column tilt 17 Quick coupling for vacuum pressure 7 Carrying handle 18 Vacuum cover 8 Feed lever 19 Gasket, vacuum cover 9 Back support 20 Gasket, base vacuum suction 10 Quick mounting 21 All
SAFETY INSTRUCTIONS Steps before using a new drilling machine • Do not use the drilling machine without first reading and understanding the contents of this Operator’s Manual. • This machine is designed for and intended for drilling concrete, brick and different stone materials. All other use is improper. • The machine is intended for use in industrial applications by experienced operators.
SAFETY INSTRUCTIONS Machine′′s safety equipment General safety precautions This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine. ! ! WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electrtic shock, fire and/or serious injury.
SAFETY INSTRUCTIONS • Never carry the machine by means of the cord and never pull out the plug by pulling the cord. • Keep all cords and extension cords away from water, oil and sharp edges. Make sure the cord is not pinched in doors, fences or the like. Otherwise it can cause the object to become live. • The power tool should not be exposed to more moisture than what is provided by the water system. Do not expose the power tool to rain.
PRESENTATION Drill motor and stand Stand • The stand is for drilling in roofs, walls and floors. • The drill stand is equipped with a quick connection plate for the drillmotor. • The base plate is made of aluminium and is therefore very light weight. It has a integrated vacuum plate. It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator′s manual as a valuable document.
ASSEMBLY Fit the wheel kit Fixing with expander or anchor Fit the wheel set in the mount on the backside of the bottom plate and tighten the screws. IMPORTANT! When drilling roofs, only expander or anchor suitable for surfaces exposed to tensile forces should be used. Use only expander or anchor which is approved for current application. Secure the stand There are three methods for fixing the stand.
ASSEMBLY Assembly of drill motor IMPORTANT! Always pull out the plug from the outlet socket before cleaning, maintenance or assembly. • Always remove the drill bit before the motor is mounted or dismounted. • Lock the feed housing lock. • Fit the drill motor on the quick mount (A). • Mount the quick mounting and drilling machine in the track on the locking clamp. • Secure with the locking screws (C).
STARTING AND STOPPING Before starting Drilling in the ceiling ! ! Use a water collector to avoid water penetrating into the machine. The machine must be covered with plastic or the like in order to prevent water penetrating into the machine, but do not cover the air intakes and air outlets. WARNING! Note the following before starting: The machine should be connected to an earthed outlet socket. Check that the mains voltage corresponds with that stated on the rating plate on the machine.
MAINTENANCE Changing the drill bit Electrical Feed ! ! WARNING! Always pull out the plug from the outlet socket before cleaning, maintenance or assembly. 1 Pull out the plug. 2 Get: - The new drill bit. - Open-ended spanners. - Water-resistant grease. WARNING! Never use damaged cables. They can cause serious, even fatal, personal injuries. Check that the cord and extension cord are intact and in good condition.
MAINTENANCE Stand maintenance ! • Adjust the lower roller by screwing anti-clockwise to guide the roller nearer to the column. • Tighten set screw to lock the guide roller shaft. • Use the feed lever to see if the feed housing moves smoothly on the column. If not, adjust the rollers again. • Fit the top and bottom plastic carraiage covers. WARNING! Inspection and/or maintenance should be carried out with the motor switched off and the plug disconnected.
MAINTENANCE Troubleshooting schedule Problem Steps on the spot Check bit. Drilling is unusually slow. Check for metal powder in waste water. Bit is stuck. Tube is abraded. Shut off drill. Probable cause Solution Bit is worn out. Replace bit. Bit is clogged with chips. Clean bit with a wire brush and increase water pressure. Diamond is rounded. Use a softer bond bit. Increase force on handle. Drill is cutting reinforcing rods. Ease up the handle to avoid tripping the circuit breaker.
TECHNICAL DATA Drill motor Electric motor Single-phase Rated voltage, V 100-120 Rated output, W 2400 Rated current, A 100-120 V 20A Weight, kg/lbs 5,9/13 Spindle speed, idle, rpm Position 1 390 Position 2 890 Drill bit Max.
US WARRANTY STATEMENT WARRANTY POLICY All warranty claims will be determined after inspection at a designated facility. A Returned Goods Authorization is required for all warranty claims. Contact Husqvarna Customer Service Department at 800-845-1312 for an RGA. The customer must prepay the freight and absorb any labor expense required to return or replace a product submitted for warranty consideration. Husqvarna will pay return shipping expenses for repaired or approved replacement products.
1151163-95 ´®z+S0G¶5W¨ ´®z+S0G¶5W¨ 2008-06-10