550iBTX EN Operator's manual Downloaded from www.Manualslib.
Contents Introduction..................................................................... 2 Troubleshooting............................................................ 17 Safety..............................................................................3 Transportation, storage and disposal........................... 17 Assembly...................................................................... 13 Technical data.............................................................. 18 Operation..........
Intended use Use the product to blow leaves and other unwanted material from areas such as lawns, pathways and asphalt roads. Start/Stop button Symbols on the product Warning! The blower can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator's manual. Please read the operator's manual carefully and make sure you understand the instructions before using the machine.
instructions in the manual are not obeyed. CAUTION: Used if there is a risk of damage to the product, other materials or the adjacent area if the instructions in the manual are not obeyed. • • • Note: Used to give more information that is necessary in a given situation. Introduction WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
• Keep bystanders away. • This appliance is not intended for use by person (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• • • • • • • by trained and qualified specialists. See instructions under the heading Maintenance. Only use original spare parts. Always ensure that ventilation openings are kept clear of debris. All covers, guards and handles must be fitted before starting. Only use the machine in daylight or in other well-lit conditions. Never use the machine in bad weather, for instance in fog, in rain, damp or in wet locations, strong winds, intense cold, risk of lightning, etc.
medical implant manufacturer before operating this product. • Remove the battery from the product during charging. Safety instructions for operation WARNING: Read the warning instructions that follow before you use the product. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability. • Do not allow children to use or be in the vicinity of the product.
• • • • • • • • • seldom necessary to use full airflow, and many work procedures can be done at half airflow. A lower airflow means less noise and less dust, and it is also easier to keep control over the rubbish collected together/moved. Use a rake or a brush to release rubbish stuck to the ground. Hold the opening of the blower as close to the ground as possible. Observe your surroundings. Direct the product away from persons, animals, play areas, cars etc.
• Watch out for thrown objects. Stones, rubbish, etc., can be thrown up into the eyes causing blindness or serious injury. • Use a residual-current device (RCI) for increased security. A residual-current device is fitted to protect operators in case an electrical fault should occur. • This product is renowned for its low vibration load. Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation.
using products for a longer coherent time of a day. Continual and regular users should have their hearing checked regularly. Note that hearing protectors limit the ability to hear sounds and warning signals. • Keep first aid equipment close at hand. • A breathing mask should be used when there is a risk of dust. Safety devices on the product • Use approved eye protection. If you use a visor, you must also use approved protective goggles. Approved protective goggles must comply with the ANSI Z87.
• Never use a product with defective safety components. The product's safety equipment must be inspected and maintained as described in this section. If your product fails any of these checks, contact your service agent to get it repaired. • All servicing and repair work on the product requires special training. This is especially true of the product′s safety equipment. If your product fails any of the checks described below you must contact your service agent.
Harness safety WARNING: Read the following warning before you operate the product. The harness must always be worn when working with the product. Failure to do so means you will be unable to operate safely and this can result in injury to yourself or others. Make sure that the waist belt and chest belt are buttoned and correctly adjusted. There is a risk that an unclosed belt can get stuck or sucked into the fan of the product.
• Replace worn or damaged parts. • If you do not do maintenance, it decreases the life cycle of the product and increases the risk of accidents. • Special training is necessary for all servicing and repair work, especially for the safety devices on the product. If not all checks in this operator's manual are approved after maintenance, speak to your servicing dealer. We guarantee that there are professional repairs and servicing available for your product. • Only use original spare parts.
9. Connect the intermediate pipe (L) to the joint swivel (H). Make sure that the knob (J) aligns with the guide track of the intermediate pipe. 1. Put on the harness of the product. A M N L H B C J 10. Turn the intermediate pipe fully to lock the control pipe and the intermediate pipe. 11. Connect the blow pipe (M) to the intermediate pipe (L). Make sure that the knob (N) on the intermediate pipe points up and goes into the guide track of the blow pipe. 12.
3. Install the battery in the backpack holder. 4. Pull the locking handles to unlock the battery. 4. Push the locking handles to lock the battery. 5. Disconnect the cable from the connector. 5. Connect the cable to the connector. 6. Remove the battery from the product. 6. Put the cable in the clip on the backpack holder. To start the product 1. To start the backpack battery, push the start button on the backpack battery. Do not continue with the steps that follow before the green LED lights is on.
5. Release the power trigger and push the Cruise control button to stop the Cruise control function. 3. Push the Boost mode button again to stop the Boost mode function. To increase the airflow to maximum 1. Start the product. Refer to To start the product on page 15. 2. Push the Boost mode button to enable maximum airflow when the power trigger is pushed. The LED comes on to show that the Boost mode function is on. The Boost mode function has no time limit.
To do a check of the air intake 1. Make sure that the air intake is not blocked. product and can cause the motor to become too hot. To clean the product, the battery and the battery charger 1. Clean the product with a dry cloth after use. 2. Clean the battery and battery charger with a dry cloth. Keep the battery guide tracks clean. 3. Make sure that these parts are clean before the battery is connected to the battery charger or the product: a) b) c) d) 2.
electrical and electronic equipment. This helps to prevent damage to the environment and to persons. Speak to local authorities, domestic waste service or your dealer for more information. Note: The symbol shows on the product or package of the product. Technical data Technical data 550iBTX Motor Motor type BLDC (brushless) 36V Weight Weight without battery, kg/ lb 6.3/13.
550iBTX Maximum air velocity in normal mode with round standard nozzle, m/s / mph 54 / 120.8 Maximum air velocity in Boost mode with round standard nozzle, m/s / mph 66 / 147.6 Maximum blow force in normal mode with round standard nozzle, N 14 Maximum blow force in Boost mode with round standard nozzle, N 21 Noise and vibration data are determined on the basis of the rated maximum speed.
EC Declaration of Conformity EC Declaration of conformity Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the battery backpack blower Husqvarna from 2018’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the requirements of the COUNCIL’S DIRECTIVES: • • • • of May 17, 2006 ”relating to machinery” 2006/42/EC.
790 - 001 - 05.12.2018 Downloaded from www.Manualslib.
Downloaded from www.Manualslib.com manuals search engine 790 - 001 - 05.12.
790 - 001 - 05.12.2018 Downloaded from www.Manualslib.
www.husqvarna.com Original instructions 1159854-26 2018-12-18 Downloaded from www.Manualslib.