Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto. the product warranty.
SAFETY RULES Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Look for this symbol to point out important safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.
• • • When loading or unloading this machine, do not exceed the maximum recommended operation angle of 15°. • Wear proper Personal Protective Equipment (PPE) while operating this machine, including (at a minimum) sturdy footwear, eye protection, and hearing protection. Do not mow in shorts or open toed footwear. Always let someone know you are outside mowing. If fuel is spilled on clothing, change clothing immediately. Never overfill fuel tank. Replace gas cap; tighten securely. V.
ASSEMBLY Read these instructions and this manual in its entirety before you attempt to assemble or operate your new lawn mower. IMPORTANT: THIS LAWN MOWER IS SHIPPED WITHOUT OIL OR GASOLINE IN THE ENGINE. Your new lawn mower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag.
ASSEMBLY TO ASSEMBLE GRASS CATCHER (See Fig. 3) INSTALL STARTER ROPE (See Fig. 4) 1. Loosen T-knob. 2. Hold control bar against upper handle. 3. Slowly pull engine starter rope out until rope will slip into loop of rope guide. 4. Tighten T-knob. 1. Put grass catcher frame into grass bag with rigid part of bag on the bottom. Make sure the frame handle is outside of the bag top. 2. Slip vinyl bindings over frame. NOTE: If vinyl bindings are too stiff, hold them in warm water for a few minutes.
OPERATION KNOW YOUR LAWN MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand their meaning.
OPERATION The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask over spectacles. HOW TO USE YOUR LAWN MOWER ENGINE SPEED The engine speed was set at the factory for optimum performance. Speed is not adjustable.
OPERATION TO CONVERT MOWER BEFORE STARTING ENGINE Your lawn mower was shipped ready to be used as a mulcher. To convert to rear bagging or discharging: ADD OIL (See Fig. 10) Your lawnmower is shipped without oil in the engine. For type and grade of oil to use, see “ENGINE” in the Maintenance section of this manual. REAR BAGGING (See Fig. 8) • Lift rear door of the lawn mower and place the grass catcher frame hooks onto the grass bag brackets.
OPERATION • CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season.
MAINTENANCE BEFORE EACH USE AFTER EACH USE EVERY 10 HOURS EVERY 25 HOURS OR SEASON EVERY 100 HOURS BEFORE STORAGE Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery ** Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug Replace Air Filter Paper Cartridge Empty fuel syste
MAINTENANCE LAWN MOWER 2. Install debris shield. 3. Position blade on the blade adapter. Always observe safety rules when performing any maintenance. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON BLADE ADAPTER. TIRES • • 4. Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine. 5. Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft. 6.
MAINTENANCE • To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.) NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position.
MAINTENANCE CARTRIDIGE • • SLOT Keep finished surfaces / wheels free of gasoline, oil, etc. With the exception of the water washout port (if equipped), we do not recommend using a garden hose to clean the outside of your lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in shortened engine life. WATER WASHOUT FEATURE (See Fig.
SERVICE AND ADJUSTMENTS CAUTION: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: 1. Release control bar and stop engine. 2. Make sure the blade and all moving parts have completely stopped. 3. Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug. LAWN MOWER TO REMOVE DRIVE BELT (See Figs. 18 & 19) TO ADJUST CUTTING HEIGHT 1. Turn lawn mower on its side with air filter and carburetor up. 2.
SERVICE AND ADJUSTMENTS 8. 9. 10. 11. Remove front belt keeper. Remove belt from front gearcase pulley. Remove all three idler pulleys from idler assembly. Remove belt from blade adapter/engine pulley and idler assembly. 12. Remove rear gearcase pulley by clamping locking pliars to input shaft (beneath pulley) and loosening pulley with a 9/16" box wrench. 13. Remove old belt from mower and discard. 6. Position the blade adapter/engine pulley on the engine crankshaft.
SERVICE AND ADJUSTMENTS TO ADJUST HANDLE (See Fig. 20) ENGINE The handle on your lawn mower has three (3) height positions - adjust to height that suits you. 1. Remove knob and carriage bolt on one side of the lower handle. 2. While holding handle assembly, remove knob and carriage bolt from opposite side, align hole in handle with desired hole in handle bracket and reassemble bolt and knob and tighten securely. 3. Align opposite side of handle with same positioning hole and secure with bolt and knob.
STORAGE ENGINE MOWING POSITION OPERATOR PRESENCE CONTROL BAR FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.
TROUBLESHOOTING POINTS PROBLEM Does not start CAUSE 1. Dirty air filter. 2. Out of fuel. 3. Stale fuel. 4. 5. 6. 7. 8. 9. 10. 11. 12. Loss of power CORRECTION 1. Clean/replace air filter. 2. Fill fuel tank. 3. Empty fuel tank and refill tank with fresh, clean gasoline. Water in fuel. 4. Empty fuel tank and refill tank with fresh, clean gasoline. Spark plug wire is disconnected. 5. Connect wire to plug. Bad spark plug. 6. Replace spark plug. Loose blade or broken blade adapter. 7.
Consumer Wheeled Products - Limited Warranty Husqvarna warrants to the original retail purchaser that this Husqvarna® product is free from defects in material or workmanship under normal use and maintenance from the date of retail purchase for the applicable Warranty Period shown on Exhibit A. This Limited Warranty may not be transferred to any subsequent purchaser of this Husqvarna® product. Certain components (e.g.
(a) Abrasion to mower decks; (b) Tires damaged by external punctures; (c) Natural discoloration of materials due to ultraviolet light; (d) Damage to cutting equipment by way of contact with, rocks, or other non-approved materials and/or structures; In addition, this Limited Warranty does not cover damages, malfunctions or failures resulting from abuse or neglect of the product related to or including any of the following: (e) Failure to provide or perform required maintenance services as prescribed
Consumer Wheeled Limited Warranty Chart 2012 Product/Component Riding Lawn Tractors: Frame, Chassis, Front Axle Engine* Transmission (if made by Husqvarna/Peerless) Transmission (if third party)** XLS Models only - stamped deck shell. Armor Protected Limited Warranty Fabricated Deck shell. Limited Lifetime Warranty Battery Other Non-Expendable Components Residential Zero Turn Mowers ( RZ Only ) Engine* Transmission ** RZ4623 (967009801 & 967009802) RZ5426 (967003601 & 967003602) - stamped deck shell.
Consumer Wheeled Limited Warranty Chart 2012 Consumer (personal, household use only) Product/Component Spreader Robotic Mowers Robotic Mower Battery Parts & Accessories (if purchased) Accessories (e.g., grass catcher, bumper guard accessories, etc. Parts (e.g., belts, blades, etc.
REGLAS DE SEGURIDAD IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. • Detenga la cuchilla o las cuchillas cuando cruce por calzadas, Busque este símbolo que señala las precaucalles o caminos de grava. ciones de seguridad de importancia.
Ponga en conocimiento de los demás que está cortando el césped. V. SERVICIO IV. MANEJO SEGURO DE GASOLINA • Usar mucha atención cuando se maneja gasolina. La gasolina es extremamente inflamable y los vapores son explosivos. • Apagar todos los cigarrillos, cigarros, pipas y otras fuentes de ignición. • Usar solo un contenedor apropiado. • Nunca quitar el tapón de la gasolina o añadir carburante con el motor en marcha. Esperar que el motor se enfríe antes de repostar la gasolina.
MONTAJE / PRE-OPERACIÓN Lea estas instrucciones y el manual completamente antes de tratar de montar u operar su segadora nueva. IMPORTANTE: Este cortacesped viene SIN ACEITE O GASOLINA en el motor. Su segadora nueva ha sido montada en la fábrica con la excepción de aquellas partes que se dejaron sin montar por razones de envío. Todas las partes como las tuercas, las arandelas, los pernos, etc., que son necesarias para completar el montaje han sido colocadas en la bolsa de partes.
MONTAJE / PRE-OPERACIÓN PARA MONTAR EL RECOGEDOR DE CÉSPED (Vea Fig. 3) INSTALACIÓN DEL CORDÓN ARRANCADOR (Vea Fig. 4) 1. 1. 2. 3. Ponga el bastidor del recogedor de césped en la bolsa del césped con la parte rígida de la bolsa en la parte inferior. Asegúrese que el mango del bastidor esté en el exterior de la parte superior de la bolsa. 2. Deslice los sujetadores de vinilo sobre el bastidor. AVISO: Si los sujetadores de vinilo están muy duros, métalos en agua caliente por algunos minutos.
OPERACIÓN FAMILIARÍCESE CON SU SEGADORA LEA ESTE MANUAL DEL DUEÑO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU SEGADORA. Compare las ilustraciones con su segadora para familiarizarse con la ubicación de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. Estos símbolos pueden apareser sobre su segadora o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
OPERACIÓN La operación de cualquier segadora puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protección para los ojos mientras opere su segadora o cuando haga ajustes o reparaciones. Recomendamos gafas o una mascara de seguridad de visión amplia de seguridad usada sobre las gafas. COMO USAR SU SEGADORA VELOCIDAD DEL MOTOR La velocidad del motor se estableció en la fábrica para un rendimiento óptimo.
OPERACIÓN PARA CONVERTIR LA SEGADORA ANTES DE HACER ARRANCAR EL MOTOR Su segadora fue enviada lista para usarse como acolchadora de capa vegetal. Para convertirla a una operación de ensacado: DESCARGA TRASERA (Vea Fig. 8) • Levantar la puerta trasera de cortacésped y colocar los ganchos del armazón de la recolectora de hierba en los soporte del quicio. • Para pasar a la operación de acolchamiento, remover la recolectora de hierba y cerrar la puerta trasera. AGREGUE ACEITE (Vea Fig.
OPERACIÓN • PRECAUCIÓN: Los combustibles mezclados con alcohol (conocidos como gasohol, o el uso de etanol o metanol) pueden atraer la humedad, la que conduce a la separación y formación de ácidos durante el almacenamiento. La gasolina acídica puede dañar el sistema del combustible de un motor durante el almacenamiento. Para evitar los problemas con el motor, se debe vaciar el sistema del combustible antes de guardarlo por un período de 30 días o más.
MANTENIMIENTO ANTES DESPUES CADA CADA CADA ANTES DEL DE CADA DE CADA 10 25 HORAS O 100 ALMACEUSO USO HORAS TEMPORADA HORAS NAMIENTO Revisar si hay Sujetadores Sueltos Limpiar/Inspeccionar el Recogedor de Césped * Controlar los Neumáticos Controlar las Ruedas Motrices *** Limpiar la Segadora **** Limpiar debajo la Cubierta de la Transmisión *** Revisar las Correas y las Poleas Impulsadas *** Revisar / Afilar / Cambiar la Cuchilla Lubricación Limpiar / Recargar la Batería ** Revisar el nivel del Aceite Cambia
MANTENIMIENTO SEGADORA 2. Instale el cubierta de la caja de engranajes. 3. Ponga la cuchilla en el adaptador. IMPORTANTE: PARA ASEGURAR LA INSTALACION APROPIADA, POSICIONE EL AGUJERO CENTRAL DE LA CUCHILLA CON LA ESTRELLA DEL CONJUNTO DEL ADAPTADOR. 4. Asegúrese de que el borde de salida de la cuchilla (opuesto al borde afilado) esté hacia arriba hacia el motor. 5. Instale el perno de la cuchilla con la arandela de seguridad y la arandela endurecida en el adaptador de la cuchilla y el cigueñal. 6.
MANTENIMIENTO 1. • La cuchilla puede afilarse con una lima o en una rueda rectificadora. No trate de afilarla mientras se encuentra en la segadora. • Para revisar el balance de la cuchilla, va a necesitar un perno de acero de 5/8", una clavija o un balanceador cónico. (Cuando se use un balanceador cónico, siga las instrucciones que vienen con el balanceador.) AVISO: No use un elavo para balancear la cuchilla. Los lóbulos del agujero central pueden aparecer como centrados, pero no lo están.
MANTENIMIENTO CARTUCHO • RANURAS • basura. Un motor tapado funciona más caliente y se acorta su duración. Mantenga las superficies pulidas y las ruedas sin gasolina, aceite, etc. Con la excepción de la boca de derrubio del agua (si está equipado), no recomendamos el uso de una manguera de jardín para limpiar la parte exterior del segadora a menos que el sistema eléctrico, el silenciador, el filtro de aire y el carburador estén tapados para evitar que les entre el agua.
SERVICIO Y AJUSTES ADVERTENCIA: Para evitar lesiónes serias, antes de dar calquier servico o de hacer ajustes: 1. Suelte la barra de control y pare el motor. 2. Asegúrese que la cuchilla y que todas las partes movibles se hayan detenido completamente. 3. Desconecte el alambre de la bujía y póngalo en donde no pueda entrar en contacto con ésta. SEGADORA PARA REMOVER CORREA DE IMPULSIÓN (Vea Figs. 18 y 19) PARA AJUSTAR LA ALTURA DE CORTE 1.
SERVICIO Y AJUSTES 8. 9. 10. 11. Remueva la fijador de la correa delantero. Remueva la correa de la polea de la correa delantero. Remueva todas las tres poleas del conjunto de la poleas. Remueva la correa del polea del motor y conjunto de la poleas. 12. Remueva la polea de la correa posterior por fijación de bloqueo pliars para eje de entrada (debajo de la polea) y aflojar polea con una llave de cubo de 9/16". 5. 6. Reinstale todas las tres poleas del conjunto de la poleas.
SERVICIO Y AJUSTES PARA AJUSTAR EL MANGO (Vea Fig. 20) MOTOR El mango de su segadora cuenta con tres (3) posiciones de altura – ajústelo a la altura que le acomode. 1. Remueva la manilla y el perno portador en un lado del mango inferior. 2. Al mismo tiempo que sujeta el conjunto del mango, remueva la manilla y el perno portador del lado opuesto, alinee el agujero en el mango con el agujero deseado en el puntal del mango y vuelva a montar el perno y la manilla y apriételos en forma segura. 3.
ALMACENAMIENTO BARRA DE CONTROL QUE EXIGE LA PRESENCIA DEL OPERADOR MOTOR POSICIÓN PARA SEGAR SISTEMA DE COMBUSTIBLE IMPORTANTE: ES IMPORTANTE EVITAR QUE SE FORMEN DEPÓSITOS DE GOMA EN PARTES FUNDAMENTALES DEL SISTEMA DE COMBUSTIBLE TALES COMO EL CARBURADOR, EL FILTRO DEL COM BUS TI BLE, LA MANGUERA DEL COMBUSTIBLE O EN EL ESTANQUE DURANTE EL ALMACENAMIENTO.
SOLUCIÓN DE PROBLEMAS PROBLEMA No arranca CAUSA CORRECCIÓN 1. 2. 3. Filtro de aire sucio. Sin combustible. Combustible rancio. 1. 2. 3. 4. Agua en el combustible. 4. 5. 6. 7. Alambre de la bujía desconectado. Bujía mala. Cuchilla suelta o adaptador de la cuchilla quebrado. Barra de control en la posición suelta. Barra de control defectuosa. Válvula del combustible (si equipada) está en la posición OFF. Batería débi (si equipada). Desconecte el conector de la batería (si equipada). Fusible quemado.
Productos con ruedas para consumidor – Garantía limitada Husqvarna garantiza al comprador minorista original que este producto Husqvarna® carece de defectos materiales o de fabricación con un uso y mantenimiento normales desde el día de la compra, dentro del periodo de garantía aplicable indicado en el Anexo A. Esta Garantía limitada on se podrá transferir a ningún comprador posterior de este producto Husqvarna®.
7. Responsabilidades del propietario. Si desea conservar sus derechos bajo esta Garantía limitada, debe realizar un cuidado y uso razonables del producto; lo que incluye cumplir con el mantenimiento preventivo, el almacenamiento, y el uso de combustible y aceite indicados en el manual del operador proporcionado. Por ejemplo, los siguientes elementos son responsabilidad del propietario y no están cubiertos por esta Garantía limitada: a.
11. Documentación requerida. Debe conservar y presentar este Comprobante de compra (que incluya la fecha, el modelo del producto y, si corresponde, el número de serie del motor) a un concesionario de servicio Husqvarna autorizado para obtener el servicio de garantía bajo esta Garantía limitada. El comprobante de compra es de su exclusiva responsabilidad. Husqvarna le recomienda que registre su producto on-line en www.usa.husqvarna.com (EE. UU.
Tabla de garantía limitada de 2012 para productos de consumo con ruedas Consumidor (personal, solo para uso doméstico) Comercial (cualquier uso comercial, profesional, institucional, agrícola o que genere ingresos, que no sea para alquiler) Anexo A Alquiler (cualquier uso para alquiler) Producto/Componente Hidrolavadoras Modelo 5525PW: Motor* * * * Bomba 2 años Sin garantía Sin garantía Otros componentes perec ederos 2 años Sin garantía Sin garantía Todas las otras hidrolavadoras (6027PW, 9032PW, 1340PW)
12/12/2013 BY