Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. SLOPE OPERATION • • • • WARNING! When loading or unloading this machine, do not exceed the maximum recommended operation angle of 15°. • Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extreme caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it. • Mow up and down slopes, not across.
PRODUCT SPECIFICATIONS Gasoline Capacity and type: 3.0 Gallons/11,36 L Regular Unleaded Oil Type: (API: SJ-SN) SAE 30 (above 32°F/0°C) SAE 5W30 (below 32°F/0°C) Oil Capacity: W/Filter: 64 Oz./1,89 L W/out Filter: 60 Oz./1,77 L Spark Plug: XC12YC (Gap: .030"/0,76 mm) Charging System: Battery: 16 AMPS @ 3600 RPM Amp/Hr: 28 Min. CCA: 230 Case size: U1R Blade Bolt Torque: 45-55 Ft. Lbs./62-75 Nm CONGRATULATIONS on your purchase of a new tractor.
UNASSEMBLED PARTS Keys (1) Quick Connect (1) Oil Drain Tube For Future Use (2) Keys Slope Sheet Battery (2) Hex Bolts (2) Nut Keps ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY NOTE: If this battery is put into service after month and year indicated on label (label is located between terminals) charge battery for minimum of one hour at 6-10 amps.
ASSEMBLY TO ADJUST THE SEAT (See Fig. 2) CHECK FOR PROPER POSITION OF ALL BELTS • Lift seat up and remove seat adjustment knob (A). • Loosen seat adjustment knob (B). NOTE: Do not remove seat adjustment knob (B). NOTE: Seat must be set until you can push the brake and forward/reverse pedals down. • Move seat to necessary position, line up the hole in the seat pan for seat adjustment knob (A) with the hole in the seat. • Install and tighten seat adjustment knob (A). • Tighten seat adjustment knob (B).
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P H E G D B F A C K J L M Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute. (H) LIGHT SWITCH - Turns the headlights on and off.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine to “backfire”.
OPERATION TO USE CRUISE CONTROL (J) (See Fig. 7) TO ADJUST GAUGE WHEELS (See Fig. 9) The cruise control feature can be used for forward travel only. Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE:Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height.
OPERATION REVERSE OPERATION SYSTEM (ROS) (See Fig. 11) TO TRANSPORT (See Fig. 3 and 12) When pushing or towing your tractor, ensure transmission is disengaged by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor. • Raise attachment lift to highest position with attachment lift control. • Pull freewheel control out until the free wheel control rod locks in extended position. • Do not push or tow tractor at more than two (2) mph (3,2 km/h).
OPERATION BEFORE STARTING THE ENGINE TO START ENGINE (See Fig. 3) The Briggs & Stratton Endurance engine equipped with your tractor features a Ready-Start automatic choke system to provide simplified starting in normal conditions. Please read the following starting instruction carefully. CHECK ENGINE OIL LEVEL The engine in your tractor has been shipped from the factory already filled with summer weight oil. • Check engine oil with tractor on level ground.
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation Check Tire Pressure T R A C T O R Check Operator Presence and ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris off Steering Plate 5 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (mode
MAINTENANCE TRACTOR BLADE CARE Always observe safety rules when per form ing any maintenance. For best results mower blades must be kept sharp. Replace bent or damaged blades. BRAKE OPERATION If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.
MAINTENANCE V-BELTS LOWER DASH COVER REMOVAL • Raise hood. • Remove fastener from lower dash cover. Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. CAUTION: Remove lower dash cover carefully to ensure cover tabs are not broken. TRANSAXLE COOLING • The transmission fan and cooling fins should be kept clean to assure proper cooling.
MAINTENANCE AIR FILTER CLEANING Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. • CLEAN AIR SCREEN • The air screen is over the air intake blower located on top of engine. The air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. Clean engine, battery, seat, finish, etc. of all foreign matter.
MAINTENANCE DECK WASHOUT PORT (See Fig. 21) Your tractor’s deck is equipped with a washout port as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Ensure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig. 22) TO INSTALL MOWER (See Figs. 22 - 34) • • • 1.
SERVICE AND ADJUSTMENTS 5. INSTALL ANTI-SWAY BAR (S) (IF EQUIPPED) (See Fig. 28 - 30) 2. ASSEMBLE FRONT GAUGE WHEEL (W) TO FRONT OF MOWER (See Fig. 25) H H. FRONT MOWER BRACKET W. FRONT GAUGE WHEEL X. SHOULDER BOLT Y. 1-1/4 O.D. WASHER Z. 3/8-16 LOCKNUT W X Z Y ANTI-SWAY BAR (S) TOWARDS TRANSAXLE 90° END TOWARDS MOWER DECK INTEGRATED WASHER END Fig. 28 Fig. 25 3. TURN STEERING WHEEL LEFT AND POSITION MOWER (See Fig.
SERVICE AND ADJUSTMENTS 6. ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 31) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor. A • Insert other end of link (E) into hole in front mower bracket (H) and secure with washer and small retainer spring (J). NOTE: Requires deck lifting. FRONT LINK LOCATION M B D H F G A. MOWER SIDE SUSPENSION ARMS B.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • Ensure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly. FRONT-TO-BACK ADJUSTMENT (See Figs. 37 & 38) IMPORTANT: Deck must be level side-to-side. Recheck measurements, adjust if necessary until both sides are equal.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 39) TO REPLACE MOTION DRIVE BELT (See Fig. 40) MOWER DRIVE BELT REMOVAL • Park tractor on a level surface. Engage parking brake. • Lower attachment lift to its lowest position. • Disengage belt tension rod (K) from lock bracket (L). Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL 1. Remove mower.
SERVICE AND ADJUSTMENTS TO CHECK BRAKE If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manual). If “jumper cables” are used for emergency starting, follow this procedure: If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1.
SERVICE AND ADJUSTMENTS TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 44) NEGATIVE (BLACK) CABLE • • • TERMINAL COVER • Raise hood. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. To replace, reverse above procedure. POSITIVE (RED) CABLE HOOD Fig. 43 TO REPLACE LED HEADLIGHT • • • • • • • HEADLIGHT WIRE CONNECTOR Raise hood. Disconnect harness from LED light. Remove mounting screws to remove LED light, reflector and lens.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION 7. Loose or damaged wiring. 8. Engine valves out of adjustment. Fill fuel tank. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 7. Check all wiring. 8. Contact an authorized service center/department. Hard to start 1. 2. 3. 4. 5. 6. 7. Dirty air filter. Bad spark plug. Weak or dead battery.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel. Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. 1. 2. 3. 4. 5. Replace blade. Tighten blade bolt. Level mower deck.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA L O NG D THIS O I T S T A E D LIN 1 5 DEG E RE E S LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles • • Mantener la máquina libre de hierba, hojas u otros escombros que pueden tocar el tubo de escape / partes del motor calientes y quemarse. No permitir que el puente del cortacésped cargue hojas u otros residuos que pueden causar acumulaciones. Limpiar toda salpicadura de aceite o carburante antes de hacer operaciones sobre la máquina o guardarla. Dejarla enfriar antes de guardarla. • • • • • III.
ESPECIFICACIONES DEL PRODUCTO Capacidad y Tipo de Gasolina: 11,36 L / 3.0 Galones Regular Sin Plomo Tipo de Aceite (API: SJ-SN): SAE 30 (sobre 32°F/0°C) SAE 5W30 (deabajo 32°F/0°C) Capacidad de Aceite: Con Filtro: Sin Filtro: Bujía XC12YC (Abertura: 0,76 mm /.030 ") Sistema de Carga: 16 AMPS @ 3600 RPM Batería: Amp/Hr: Min. CCA: Modelo Tamaño: Torsión del Perno de la Cuchilla: FELICITACIONES por la compra de su tractor.
PEDAZOS PARA LA MONTAJE Llaves (1) Accesorio del conexión (1) Tubo de desagüe (2) Llaves Batería Hoja de pendiente (2) Perno (2) Tuerca MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío.
MONTAJE REVISIÓN DE LA POSICIÓN ADECUADA DE TODAS LAS CORREAS PARA AJUSTAR EL ASIENTO (Vea Fig. 2) • Levante el asiento y retire la perilla de ajuste de este (A). • Suelte la perilla de ajuste del asiento (B). NOTA: No retire la perilla de ajuste del asiento (B). NOTA: El asiento se debe ajustar hasta que pueda pisar los pedales de freno y de avance/retroceso. • Mueva el asiento a la posición necesaria, alinee el orificio en la base del asiento para la perilla de ajuste (A) con el agujero en el asiento.
OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados.
OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL DE OPERARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. P H E G D B F A C K J L M Fig. 3 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute. (H) INTERRUPTOR DE LA LUZ – Enciende y apaga las luces delanteras.
OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas.
OPERACIÓN UTILIZAR EL MANDO CRUCERO (Vea Fig. 7) • El césped promedio debe cortarse aproximadamente a 63,5 mm (2-1/2 pulgadas) durante la temporada fría y sobre 76,2 mm (3 pulgadas) durante los meses calurosos. Para obtener un césped más saludable y de mejor apariencia, siegue a menudo y después de un crecimiento moderado. • Para obtener el mejor rendimiento de corte, el césped que tiene más de 152,4 mm (6 pulgadas) de altura debe segarse dos veces.
OPERACIÓN PARA OPERAR EN CERROS PARA PARAR LAS CUCHILLAS DE LA SEGADORA • Desenganche el control del embrague del accesorio. ADVERTENCIA: No maneje hacia arriba o hacia abajo en cerros con pendientes superiores a 15° y no maneje atravesando ninguna pendiente. Utilice la guía de la pendiente proporcionada en la parte posteriora de este manual.
OPERACIÓN ANTES DE HACER ARRANCAR EL MOTOR ARRANQUE DEL MOTOR (Vea Fig. 3) REVISE EL NIVEL DE ACEITE DEL MOTOR El motor Briggs & Stratton Endurance instalado en su tractor cuenta con un sistema estrangulador automático que simplifica el arranque en condiciones normales. Lea con atención las siguientes instrucciones de arranque. El motor de su tractor se envía de fábrica ya lleno con aceite de peso para verano. • Revise el aceite del motor con el tractor en terreno nivelado.
OPERACIÓN CONSEJOS PARA SEGAR PURGAR LA TRANSMISIÓN • PRECAUCIÓN: Nunca enganche o desenganche la palanca del control de rueda libre cuando el motor esta funcionando. • Para asegurar la operación y ejecución adecuada, es recomendado que la transmisión sea purgada antes de operar el tractor para la primera vez. Este proceso removerá cualquier aire adentro de la transmisión que se halla formado durante el transporte de su tractor.
MANTENIMENTO PROGRAMA DE MANTENIMIENTO ANTES DE CADA USO CADA 8 HORAS CADA 25 HORAS CADA 50 HORAS CADA 100 HORAS CADA TEMPORADA ALMACENAMIENTO Revisar la operación del freno Revisar la presión de las llantas T R A C T O R Verificar la sistemas presencia del operador y sistemas "ROS" Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora 3 Tabla de lubricación Revisar el nivel de bateria 4 Limpiar la batería y los tereminales Limpie los residuos de la placa de dirección.
MANTENIMENTO TRACTOR PRECAUCIÓN: Usar solamente la hojas de repuesto aprobada por el fabricante de su cortacésped. Usar una hoja no aprobada por el fabricante de su cortacésped es peligroso, puede dañar su cortacésped y anular su garantía. Siempre observe las reglas de seguridad cuando dé mantenimiento.
MANTENIMENTO CORREAS V EXTRACCIÓN DE LA CUBIERTA DEL TABLERO INFERIOR • Levantar la capota. • Retirar el sujetador de la cubierta del tablero inferior. PRECAUCIÓN: Retirar la cubierta del tablero inferior con cuidado para que no se rompan las lengüetas de la cubierta. • Deslizar la cubierta del tablero inferior hacia arriba para liberar las lengüetas de la cubierta de las ranuras cónicas del tablero inferior y retirarla.
MANTENIMENTO LIMPIEZA LIMPIEZA DE LA PANTALLA DE AIRE La pantalla de aire está sobre el soplador de la toma de aire que se ubica en la parte superior del motor. La pantalla de aire se debe mantener libre de suciedad y paja para evitar que el motor se dañe por sobrecalentamiento. Limpie con un cepillo de alambre o con aire comprimido para retirar la suciedad y las fibras de goma secas difíciles de quitar.
MANTENIMENTO PUERTO DE LAVADO DE LA CUBIERTA (Vea Fig. 21) La plataforma del tractor está equipada con un puerto de lavado como parte del sistema de lavado de la plataforma. Se debe utilizar después de cada uso. 1. Lleve el tractor a un lugar horizontal y despejado de su césped, lo bastante cerca de una boca de riego como para que llegue la manguera del jardín. IMPORTANTE: Asegúrese de que la boca de descarga del tractor está orientada LEJOS de su casa, garaje, coches aparcados, etc.
SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal de freno completamente y aplique el freno de estacionamiento. • Ponga el embrague del accesorio en la posición "DESENGANCHADO". • Ponga la llave de ignición en la posición de apagado (STOP) y remuévala. • Asegúrese que las cuchillas y que todas las partes movibles se hayan detenido completamente.
SERVICIO Y AJUSTES 2. ARME LA RUEDA CALIBRADORA DELANTERA (W) EN LA PARTE DELANTERA DE LA CORTADORA DE CÉSPED (Vea Fig. 25) H BARRA ANTIBALANCEO (S) H. ESCUADRA DE LA CORTADORA DE CÉSPED DELANTERA W. RUEDA CALIBRADORA DELANTERA X. PERNO CON RESALTO Y. ARANDELA DE 1-1/4 Z. TUERCA DE SEGURIDAD DE 3/8-16 W X Y Z 5. SI LA TIENE, INSTALE LA BARRA ANTIBALANCEO (S) (Vea Fig. 28 - 30) HACIA EL TRANSEJE EXTREMO EN 90° HACIA LA PLATAFORMA DE LA CORTADORA DE CÉSPED EXTREMO CON ARANDELA INTEGRADA Fig.
SERVICIO Y AJUSTES 6. INSTALE LOS BRAZOS DE SUSPENSIÓN LATERAL DE LA CORTADORA DE CÉSPED (A) EN EL CHASIS (Vea Fig. 31) • Ubique el agujero delantero del brazo de suspensión lateral (A) sobre la chaveta en la parte exterior del chasis del tractor y asegure con una arandela grande y un resorte de retención grande (B). • Repita en el lado opuesto del tractor.
SERVICIO Y AJUSTES PARA NIVELAR LA SEGADORA AJUSTE DE DELANTE A ATRÁS (Vea Fig. 37 y 38) Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco inflados, el césped no le quedará bien cortado, lo cual podrá llevarlo a pensar que la segadora no está bien regulada. IMPORTANTE: El piso debe quedar bien nivelado de lado a lado.
SERVICIO Y AJUSTES PARA REEMPLAZAR LA CORREA DE LA CUCHILLA DE LA SEGADORA (See Fig. 39) PARA CAMBIAR LA CORREA DE IMPULSIÓN DE MOVIMIENTO (Vea Fig. 40) DESMONTAJE DE LA CORREA DE LA SEGADORA • Estacione el tractor en una superficie nivelada. Ponga el freno de mano. • Baje la palanca elevadora a la posición de más abajo. • Retire la barra de tensión de la correa (K) de la barra de sujeción (L). Estacione el tractor en una superficie nivelada. Ponga el freno de mano.
SERVICIO Y AJUSTES CONTROLAR Y AJUSTAR EL FRENO Si su batería está demasiado baja como para hacer arrancar el motor tiene que volverse a cargar. (Vea “Batería” en la sección de Mantenimiento de este manual).
SERVICIO Y AJUSTES PARA REMOVER EL CONJUNTO DEL CAPÓ Y DEL ENREJADO (Vea Fig. 44) CABLE NEGRO (NEGATIVO) 1. Levante el capó. 2. Desabroche el conector del alambre de las luces delanteras. 3. Párese delante del tractor. Agarre el capó en los lados, inclínelo un poco hacia el motor y sáquelo del tractor. 4. Para volver a instalar el capó, asegúrese de volver a conectar el conector del alambre de las luces. CUBIERTA TERMINAL CAPOTA CABLE ROJO (POSITIVO) Fig.
ALMACENAMIENTO MOTOR Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA No arranca CAUSA CORRECCIÓN 1. 2. 3. 4. 5. 6. Sin combustible. Motor ahogado. Bujía mala. Filtro de aire sucio. Filtro de combustible sucio. Agua en el combustible. 1. 2. 3. 4. 5. 6. 7. 8. Alambrado suelto o dañado. Válvulas del motor desajustadas. 7. 8. 1. 2. 3. 4. 5. Filtro de aire sucio. Bujía mala. Batería baja o descargada. Filtro de combustible sucio. Combustible rancio o sucio. 1. 2. 3. 4. 5. 6. 7. Alambrado suelto o dañado.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA CAUSA El motor continúa funcionando cuando el operador se baja del asiento con el embrague del accesorio enganchado 1. El corte disparejo 1. 2. 3. Mala descarga del césped 1. Revise el alambrado, los interruptores y la conexiones.Si no están correctas, pongase en contacto con un centro de servicio cualificado. PRECAUCIÓN: NO opere la máquina sino hasta haber corregido el problema. Cuchilla desgastada, doblada o suelta. El conjunto segador no estánivelado.
GUÍA SUGERIDA PARA MEDIR LAS PENDIENTES CON LA VISTA PARA UNA OPERACIÓN SEGURA P L E G AR A LO EST L A RGO A ES DE U N L A A PEN LÍNE DIE A P N U T NTE E DE ADA 1 5 GRA DOS SOLAMENTE ANDE CUESTA ARRIBA O CUESTA ABAJO Y NO ATRAVIESE EL CERRO 15 GRADOS MAX. ADVERTENCIA: Para evitar daños graves, haga funcionar su tractor arriba y abajo de las pendientes, nunca transversalmente con respecto a las pendientes. No cortar pendientes mayores de 15 grados.
08.22.19 CL Printed in U.S.A.