Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. Esta máquina puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (E10) anulará la garantía del producto. the product warranty.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN • • WARNING. CHILDREN CAN BE INJURED BY THIS EQUIPMENT. The American Academy of Pediatrics recommends that children be a minimum of 12 year of age before operating a pedestrian controlled lawn mower and a minimum of 16 years of age before operating a riding lawn mower. If fuel is spilled on clothing, change clothing immediately. Never overfill fuel tank. Replace gas cap and tighten securely.
PRODUCT SPECIFICATIONS Gasoline Capacity And Type: 2.5 Gallons / 9,46 L Unleaded Regular Oil Type (API:SG-SL): SAE 10W 30 (Above 32°F/0°C) SAE 5W30 (Below 32°F/0°C) Oil Capacity: W/Filter: 51 Oz./1,5 L W/O Filter: 35 Oz./1,05 L Spark Plug: Champion RC12YC (Gap: .030"/.76 mm) Ground Speed (Mph/Kph): Forward: Reverse: Charging System: 15 @ 3600 RPM Battery: AMP/HR: 28 MIN. CCA: 230 Case Size: U1R Blade Torque: 45-55 Ft. Lbs. (62-75 Nm) CONGRATULATIONS on your purchase of a new tractor.
UNASSEMBLED PARTS Keys Slope Sheet (2) Keys ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. TOOLS REQUIRED FOR ASSEMBLY ADJUST SEAT (See Fig. 2) A socket wrench set will make assembly easier. Standard wrench sizes are listed. (1) 1/2" wrench Tire pressure gauge (2) 7/16" wrenches Utility knife Pliers • • • Sit in seat.
ASSEMBLY ✓CHECKLIST CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P H G D E C B F A M J Fig. 3 Our tractors conform to the applicable safety standards of the American National Standards Institute. (A) ATTACHMENT LIFT LEVER - Used to raise and lower the mower or other attachments mounted to your tractor.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping, may cause engine to “backfire”.
OPERATION TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8) TO OPERATE MOWER Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills. • Select desired height of cut with attachment lift lever.
OPERATION NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.). REVERSE OPERATION SYSTEM (ROS) Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.
OPERATION MOWING TIPS TO START ENGINE (See Fig. 3) • When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Ensure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress clutch/brake pedal and set parking brake. • Place motion control lever in neutral position. • Move attachment clutch to “DISENGAGED” position. • Move throttle control to choke position.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) E N G I N E
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.
MAINTENANCE V-BELTS • Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. CAUTION: If engine has been operated for an extended period of time immediately prior to draining oil, oil will be hot.
MAINTENANCE AIR FILTER CLEANING Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See engine manual. • • CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. Clean engine, battery, seat, finish, etc. of all foreign matter. Clean debris from steering plate.
MAINTENANCE DECK WASHOUT PORT (See Fig. 20) Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Ensure the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached. 2.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Ensure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS • • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring. Repeat on opposite side of tractor. • Insert end of link (E) into hole in front mower bracket and secure with washer and retainer spring (J). E A J F H B • Fig.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see step in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Fig. 29 & 30) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 31) TO REPLACE MOTION DRIVE BELT (See Fig. 32) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL • Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).
SERVICE AND ADJUSTMENTS TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Figs. 33 and 34) TO REMOVE WHEEL (See Fig. 35) • • The motion control lever has been preset at the factory and adjustment should not be necessary. • Engage the freewheel control lever. (See "TO TRANSPORT" in the Operations section of this manual.) • Move the motion control lever until the unit rolls freely. • While holding motion control lever in place, loosen the adjustment bolt.
SERVICE AND ADJUSTMENTS TO START ENGINE WITH A WEAK BATTERY (See Fig. 36) REPLACING BATTERY (See Fig. 37) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from ac ci den tal grounding. WARNING: Lead-acid batteries generate explosive gases.
SERVICE AND ADJUSTMENTS TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 38) • • • • Raise hood. Unsnap headlight wire connector. Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. To replace, reverse above procedure. HOOD HEADLIGHT WIRE CONNECTOR 07002 Fig. 38 ENGINE TO ADJUST THROTTLE CONTROL CABLE The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is necessary, see engine manual.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel.
1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parallel to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure. 4. Compare the angle of the fold with the slope of the hill. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees.
&RQVXPHU :KHHOHG 3URGXFWV ± /LPLWHG :DUUDQW\ +XVTYDUQD ZDUUDQWV WR WKH RULJLQDO UHWDLO SXUFKDVHU WKDW WKLV +XVTYDUQD SURGXFW LV IUHH IURP GHIHFWV LQ PDWHULDO RU ZRUNPDQVKLS XQGHU QRUPDO XVH DQG PDLQWHQDQFH IURP WKH GDWH RI UHWDLO SXUFKDVH IRU WKH DSSOLFDEOH :DUUDQW\ 3HULRG VKRZQ RQ ([KLELW $ &HUWDLQ FRPSRQHQWV H J HQJLQHV DQG WUDQVPLVVLRQV DUH H[FOXGHG IURP FRYHUDJH DQG RWKHU OLPLWDWLRQV DSSO\ DV GHVFULEHG LQ WKLV GRFXPHQW +XVTYDUQD ZLOO UHSDLU RU UHSODFH DW LWV GLVFUHWLRQ DQ\ GHIHFWLYH SURG
F 3UHYHQWDWLYH PDLQWHQDQFH DV RXWOLQHG LQ WKH RSHUDWRU¶V PDQXDO ,Q DGGLWLRQ \RX PXVW FHDVH XVLQJ WKH SURGXFW LPPHGLDWHO\ XSRQ DQ\ IDLOXUH RU GDPDJH 7KH SURGXFW VKRXOG EH WDNHQ WR DQ DXWKRUL]HG +XVTYDUQD VHUYLFLQJ GHDOHU SULRU WR DQ\ IXUWKHU XVH 'DPDJHV UHVXOWLQJ IURP QRUPDO DJLQJ ZHDU DQG WHDU RU QHJOHFW DUH 127 FRYHUHG 7KH /LPLWHG :DUUDQW\ GRHV QRW FRYHU GDPDJH RWKHU WKDQ WKDW UHVXOWLQJ IURP GHIHFWV LQ PDWHULDO RU ZRUNPDQVKLS 7KH IROORZLQJ DUH 127 FRQVL
&RQVXPHU :KHHOHG :DUUDQW\ &KDUW ([KLELW $ &RQVXPHU SHUVRQDO KRXVHKROG XVH RQO\ 3URGXFW &RPSRQHQW 5LGLQJ /DZQ 7UDFWRUV )UDPH &KDVVLV )URQW $[OH (QJLQH 7UDQVPLVVLRQ LI PDGH E\ +XVTYDUQD 3HHUOHVV 7UDQVPLVVLRQ LI WKLUG SDUW\ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV 5HVLGHQWLDO =HUR 7XUQ 0RZHUV 5= 2QO\ (QJLQH 7UDQVPLVVLRQ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV 5HVLGHQWLDO =HUR 7XUQ 0RZHUV 0= (= (QJLQH 7UDQVPLVVLRQ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV /( (GJHU (QJLQH
&RQVXPHU :KHHOHG :DUUDQW\ &KDUW ([KLELW $ &RQVXPHU SHUVRQDO KRXVHKROG XVH RQO\ &RPPHUFLDO DQ\ FRPPHUFLDO 5HQWDO DQ\ UHQWDO SURIHVVLRQDO LQVWLWXWLRQDO XVDJH DULJFXOXWUDO RU LQFRPH SURGXFLQJ XVH RWKHU WKDQ 5HQWDO 8VH 3URGXFW &RPSRQHQW )URQW 0RXQWHG 'HFN 5LGHUV (QJLQH 7UDQVPLVVLRQ
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles PELIGRO: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE. • Nunca dejar una máquina encendida sin vigilancia.
REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles III. NIÑOS • • ADVERTENCIA: LOS NIÑOS PUEDEN SUFRIR DAÑOS CON EL USO DE ESTE EQUIPO. La Academia Estadounidense de Pediatría (American Academy of Pediatrics) recomienda que sólo se permita a niños con una edad mínima de 12 años manejar máquinas cortacésped manuales, y al menos de 16 años para manejar tractores cortacésped.
ESPECIFICACIONES DEL PRODUCTO Capacidad y Tipo de gasolina: 2.5 Galones (9,46 L) Regular Sin Plomo Tipo de Aceite: (API:SG-SL) SAE 30 (Sobre 32°F/0°C) SAE 10W30 (Debajo 32°F/0°C) Capacidad de petróleo Con filtro: Sin filtro: Bujía: Champion RC12YC (Abertura: .030"/0,76 mm) Velocidad de Recorrido (Mph/Kph): Delante: 0 - 5,2/8,4 Marcha Atrás: 0 - 2,9/4,7 Sistema de Carga: 15 @ 3600 RPM Batería: Amp/Hr: Min.
PEDAZOS PARA LA MONTAJE Hoja de pendiente Llaves Llaves (2) MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío. HERRAMIENTAS NECESARIAS PARA EL MONTAJE PARA AJUSTAR EL ASIENTO (Vea Fig. 2) • • Un juego de llaves de tubo facilitará el montaje. A continuación se enumeran los tamaños de las llaves estándar.
MONTAJE ✓LISTA DE REVISIÓN REVISIÓN DE LA NIVELACIÓN DEL CONJUNTO Para obtener los mejores resultados en el corte, la caja de la segadora tiene que estar nivelada en la forma adecuada. Vea “PARA NIVELAR LA CAJA” en la sección de Servicio y Ajustes de este manual. ANTES DE OPERAR Y DE DISFRUTAR DE SU TRACTOR NUEVO, LE DESEAMOS QUE RECIBA EL MEJOR RENDIMIENTO Y LA MAYOR SATISFACCION DE ESTE PRODUCTO DE CALIDAD.
OPERACIÓN Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados. -!2#(!ª!42«3 .%542/ !,4/ "!*/ %342!.'5 ,!#)». 2«0)$/ ,%.4/ ª ª -/4/2 !0!'!$/ -/4/2ª -/4/2 %.#%.$)$/ %.ª-!2#(! 3)34%-! &5.#)/.!-)%.4/ !42«3ª 2/3 ,5#%3 %.3%.$)$!3 #/-"534)",% &2%./ª$% !,452!ª$%ª,!ª ,%6!.4!-)%.4/ %34!#)/.!-)%.4/ 3%'!$/2! ª$%ª,!ª3%'!$/2! -!2#(! "!4%2¶! -!2#(! 0!,!.#!ª$%ª-!.$/ª 0%$!,ª$%ª&2%./ª ª !42«3 (!#)!ª!$%,!.
OPERACIÓN FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL DEL DUEÑO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ubicaciones de los diversos controles y ajustes. Guarde este manual para referencia en el futuro. P H G D E C B F A M J Fig. 3 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute.
OPERACIÓN La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o protecciones para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomendamos gafas de seguridad o una máscara de visión amplia de seguridad usada sobre las gafas. COMO USAR SU TRACTOR • Nunca use la estrangulación para parar el motor.
OPERACIÓN PARA AJUSTAR LA ALTURA DE CORTE DE LA SEGADORA (Vea Fig. 8) PARA OPERAR LA SEGADORA Su tractor viene equipada con un interruptor sensor que exige la presencia del operador. Si el motor está funcionando y el embrague del accesorio está enganchado y el operador trata de bajarse del asiento, se apagará el motor. Tiene que mantenerse sentado completa y centralmente en el asiento para impedir que el motor vacile o se apague cuando se opere su equipo en terreno disparejo, áspero o en cerros.
OPERACIÓN FUNCIONAMIENTO ATRÁS AVISO: Para proteger el capota contra el daño cuando transporte su tractor en un camión o remolcador, asegúrese que el capota esté cerrado y asegurado al tractor. Use los medios apropiados para amarrar el capota al tractor (cuerdas, cordeles, etc.) Tu tractor está equipado con el Sistema de Funcionamiento Atrás (ROS).
OPERACIÓN • Ponga la palanca de control en neutro. Alivie el freno de estacionamiento y deje que el embrague/freno vuelva a la posición de operación. • Permita que la transmisión se caliente durante un minuto. Esto puede ser echo durante el tiempo de calentamiento del motor. • Los accesorios pueden ser utilizados durante el periodo del recalentamiento del motor después que la transmisión halla sido calentada.
MANTENIMIENTO ANTES DE CADA USO CADA 25 HORAS CADA 8 HORAS CADA 50 HORAS CADA 100 HORAS CADA ALMACENAMIENTO TEMPORADA Revisar la operación del freno T R A C T 0 R Revisar la presión de las llantas Vérifiéz la commande de présence d'opérateur et le sistema d ROS Revisar si hay sujetadores sueltos Afilar/cambiar las cuchillas de la segadora 3 Tabla de lubricación Revisar el nivel 4 Limpiar la batería y los terminales Limpie los residuos de la placa de dirección.
MANTENIMIENTO TRACTOR CUIDADO DE LA CUCHILLA Para obtener resultados óptimos, las cuchillas de la cortadora deben estar afiladas. Reemplace las cuchillas que estén gastadas, dobladas o dañadas. Siempre observe las reglas de seguridad cuando dé mantenimiento. OPERACIÓN DEL FRENO PRECAUCIÓN: Usar solamente la hojas de repuesto aprobada por el fabricante de su cortacésped. Usar una hoja no aprobada por el fabricante de su cortacésped es peligroso, puede dañar su cortacésped y anular su garantía.
MANTENIMIENTO CORREAS V • Revise las correas V para verificar si existe deterioro y desgaste después de 100 horas de operación y cámbielas si es necesario. Las correas no son ajustables. Cambie las correas si empiezan a deslizarse debido al desgaste. Remueva la tapa/varilla indicadora de nivel para relleno del aceite. Tenga cuidado de no permitir que la mugre entre en el motor cuando cambie el aceite.
MANTENIMIENTO FILTRO DEL AIRE LIMPIEZA Su motor puede sufrir averías y funcionar de manera incorrecta con un filtro del aire sucio. Déle servicio al filtro de aire más a menudo si se usa en condiciones polvorosas. Vea la manual de la motor. • • LIMPIEZA DE LA REJILLA DE AIRE La rejilla de aire debe mantenerse sin mugre y paja para evitar el daño al motor debido al sobrecalentamiento. Límpiela con un cepillo de alambre o con aire comprimido para remover la mugre y las fibras de goma secas, pegadas.
MANTENIMIENTO PUERTO DE LAVADO DE LA CUBIERTA (Vea Fig. 20) La cubierta de su tractor está equipada con un puerto de lavado sobre la superficie que forma parte del sistema de lavado de la cubierta. Se debería utilizar cada vez que se haya usado el tractor. 1. Lleve el tractor a un lugar horizontal y despejado de su césped, lo bastante cerca de una boca de riego como para que llegue la manguera del jardín.
SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal del embrague/freno completamente y aplique el freno de estacionamiento. • Ponga la palanca de control de movimiento en la posición de neutro (N). • Ponga el embrague del accesorio en la posición desenganchado (DISENGAGED). • Ponga la llave de ignición en la posición de apagado (STOP) y remuévala.
SERVICIO Y AJUSTES • • • FIJE LOS BRAZOS DE SUSPENSIÓN LATERALES DE LA CORTADORA (A) AL CHASIS - Ubique el orificio del brazo encima de la clavija (B) que hay en la parte exterior del chasis del tractor, y fíjelo con una resorte de contención. Realice el mismo procedimiento en el otro lado del tractor. Meta el fin de la conexión (E) en el hoyo en el suporte anterior de orificio y conecte con arandela e Retén del resorte (J). E A J F H B • Fig.
SERVICIO Y AJUSTES PARA NIVELAR LA SEGADORA AJUSTE DE DELANTE A ATRÁS (Vea Fig. 29 y 30) Asegúrese de que los neumáticos estén inflados a la PSI que se indica en estos. Si están demasiado inflados o poco inflados, el césped no le quedará bien cortado, lo cual podrá llevarlo a pensar que la SEGADORA no está bien regulada. IMPORTANTE: El piso debe quedar bien nivelado de lado a lado.
SERVICIO Y AJUSTES PARA CAMBIAR LA CORREA DE LA CUCHILLA DE LA SEGADORA (Vea Fig. 31) PARA REEMPLAZAR LA CORREA DE TRANSMISIÓN (Vea Fig. 32) La correa de la cuchilla de la segadora se puede cambiar sin herramientas. Estacione el tractor en una superficie nivelada. Enganche el freno de estacionamiento. Estacione el tractor en una superficie nivelada. Ponga el freno de mano. Si necesita asistencia, del lado de abajo del apoyapiés hay una guía práctica para el montaje de la correa.
SERVICIO Y AJUSTES PARA REMOVER LAS RUEDAS (Vea Fig. 35) REGULACIÓN DE LA PALANCA DE CONTROL DEL MOVIMIENTO NEUTRO DEL CAMBIO MECÁNICO • • La palanca de control del movimiento del cambio mecánico ya viene predefinida por la Casa constructora y por lo tanto no requiere ulteriores regulaciones. • Accione la palanca de control de la rueda libre. (Ver “PARA TRANSPORTAR” en la Sección "Operación" de este manual.) • Mueva la palanca de control de movimiento hasta que la unidad ruede libremente.
SERVICIO Y AJUSTES PARA HACER ARRANCAR EL MOTOR CON UNA BATERÍA BAJA (Vea Fig. 36) REEMPLAZAR LA BATERIA (Vea Fig. 37) ADVERTENCIA: No haga cortocircuito con los terminales de la batería al permitir que una llave de tuerca o cualquier otro objeto entre en contacto con ambos terminales a la misma vez. Antes de instalar la batería remueva las pulseras de metal, los relojes de pulsera de metal, los anillos, etc.
SERVICIO Y AJUSTES PARA REMOVER EL CONJUNTO DEL CAPÓ Y DEL ENREJADO (Vea Fig. 38) • • • • Levante el capó. Desabroche el conector del alambre de las luces delanteras. Párese delante del tractor. Agarre el capó en los lados, inclínelo un poco hacia el motor y sáquelo del tractor. Para volver a instalar el capó, asegúrese de volver a conectar el conector del alambre de las luces. CAPÓ CONECTOR DEL ALAMBRE DE LAS LUCES DELANTERAS 07002 Fig.
ALMACENAMIENTO MOTOR Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más. SISTEMA DE COMBUSTIBLE Advertencia: Nunca almacene el tractor con gasolina en el estanque dentro de un edificio en donde los gases pueden alcanzar una llama expuesta o una chispa. Permita que el motor se enfríe antes de almacenarlo en cualquier recinto privado.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA No arranca CAUSA 1. 2. 3. 4. 5. 6. 7. 3. 4. 5. 6. 7. 8. 9. Alambrado suelto o dañado. Carburador desajustado. 8. 9. 10. Difícil de arrancar CORRECCIÓN Sin combustible. Motor sin la “ESTRANGULACIÓN” (CHOKE) adecuada. Motor ahogado. Bujía mala. Filtro de aire sucio. Filtro de combustible sucio. Agua en el combustible. Válvulas del motor desajustadas. 1. 2. 10. Llene el estanque de combustible. Vea “PARA HACER ARRANCAR EL MOTOR” en la sección de operación.
IDENTIFICACIÓN DE PROBLEMAS PROBLEMA Vibración excesiva CAUSA CORRECCIÓN 1. 2. 3. Cuchilla desgastada, doblada o suelta. Mandril de la cuchilla doblado. Parte(s) suelta(s)/dañada(s). 1. 2. 3. Cambie la cuchilla. Apriete el perno de la cuchilla. Cambie la mandril de la cuchilla. Apriete la(s) parte(s). Cambie las partes dañadas. El motor continúa funcionando cuando el operador se baja del asiento con el embrague del accesorio enganchado 1.
GUÍA SUGERIDA PARA MEDIR LAS PENDIENTES CON LA VISTA PARA UNA OPERACIÓN SEGURA PL E G AR A LO EST L A RGO A ES DE U N L A A PEN LÍNE DIE A P N U T NTE E DE ADA 1 5 GRA DOS SOLAMENTE ANDE CUESTA ARRIBA O CUESTA ABAJO Y NO ATRAVIESE EL CERRO 15 GRADOS MAX. ADVERTENCIA: Para evitar daños graves, haga funcionar su tractor arriba y abajo de las pendientes, nunca transversalmente con respecto a las pendientes. No cortar pendientes mayores de 15 grados.
3URGXFWRV FRQ UXHGDV SDUD FRQVXPLGRU *DUDQWtD OLPLWDGD +XVTYDUQD OH JDUDQWL]D DO FRPSUDGRU PLQRULVWD RULJLQDO TXH HVWH SURGXFWR +XVTYDUQD HVWi OLEUH GH GHIHFWRV GH PDWHULDO R PDQR GH REUD EDMR XVR \ PDQWHQLPLHQWR QRUPDOHV D SDUWLU GH OD IHFKD GH FRPSUD PLQRULVWD SRU HO SHUtRGR GH JDUDQWtD DSOLFDEOH TXH VH LQGLFD HQ HO $QH[R $ &LHUWRV FRPSRQHQWHV SRU HMHPSOR ORV PRWRUHV \ ODV WUDQVPLVLRQHV TXHGDQ H[FOXLGRV GH OD FREHUWXUD \ DSOLFDQ RWUDV OLPLWDFLRQHV VHJ~Q VH
$GHPiV XVWHG GHEH GHMDU GH XWLOL]DU HO SURGXFWR GH LQPHGLDWR VL VH SURGXFH FXDOTXLHU IDOOD R GDxR (O SURGXFWR GHEH OOHYDUVH D XQ FRQFHVLRQDULR GH VHUYLFLR +XVTYDUQD DXWRUL]DGR DQWHV GH VHJXLU XWLOL]iQGROR /RV GDxRV TXH UHVXOWDQ GHO HQYHMHFLPLHQWR \ GHVJDVWH QRUPDOHV R ORV GDxRV SRU QHJOLJHQFLD 12 HVWiQ FXELHUWRV /D *DUDQWtD OLPLWDGD QR FXEUH RWURV GDxRV IXHUD GH ORV TXH UHVXOWDQ GH GHIHFWRV HQ HO PDWHULDO R OD PDQR GH REUD /RV VLJXLHQWHV 12 VH FRQVLGHUDQ GHIHFWRV HQ HO PDWHUL
&XDGUR GH JDUDQWtD SDUD SURGXFWRV FRQ UXHGDV SDUD FRQVXPLGRU $QH[R $ &RQVXPLGRU &RPHUFLDO $OTXLOHU FXDOTXLHU SHUVRQDO XVR FXDOTXLHU XVR FRPHUFLDO XVR SDUD DOTXLOHU GRPpVWLFR ~QLFDPHQWH SURIHVLRQDO LQVWLWXFLRQDO DJUtFROD R TXH SURGX]FD LQJUHVRV TXH QR VHD XVR SDUD DOTXLOHU 3URGXFWR &RPSRQHQWH 7UDFWRUHV FRUWDFpVSHG %DVWLGRU FKDVLV HMH GHODQWHUR 0RWRU 7UDQVPLVLyQ VL HV IDEULFDGD SRU +XVTYDUQD 3HHUOHVV 7UDQVPLVLyQ VL HV GH WHUFHURV %DWHUtD 2WURV FRPSRQHQWHV SHUHFHGHURV &DUULWRV U
&XDGUR GH JDUDQWtD SDUD SURGXFWRV FRQ UXHGDV SDUD FRQVXPLGRU $QH[R $ $OTXLOHU FXDOTXLHU &RQVXPLGRU &RPHUFLDO FXDOTXLHU XVR FRPHUFLDO XVR SDUD DOTXLOHU SHUVRQDO XVR GRPpVWLFR ~QLFDPHQWH SURIHVLRQDO LQVWLWXFLRQDO DJUtFROD R TXH SURGX]FD LQJUHVRV TXH QR VHD XVR SDUD DOTXLOHU 3URGXFWR &RPSRQHQWH &DUULWRV SDUD SODWDIRUPD GH PRQWDMH IURQWDO 0RWRU 7UDQVPLVLyQ DxRV %DWHUtD DxR SURUUDWHDGR 2WURV FRPSRQHQWHV SHUHFHGHURV DxRV &XOWLYDGRUDV %DWHUtD DxR SURUUDWHDGR 2WURV FRPSRQHQWHV SH
08/25/2011 TH