07002 YTH26V54 Owner's Manual "This machine is approved by the EPA for E10 (10% ethanol) and lower fuel only. Do not use any fuel >E10 in this machine.
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. • Be alert and turn machine off if a child enters the area.
CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized servicecenter/ department We have competent, well-trained technicians and the proper tools to service or repair this tractor. Please read and retain this manual. The instructions will enable you to assemble and maintain your tractor properly.
UNASSEMBLED PARTS Mower Front Wheel (1) Shoulder Bolt (1) 1-1/4 O.D. Washer (1) 3/8-16 Locknut Mower (5) 1-3/16 O.D. Washers (1) Small Retainer Springs (5) Large Retainer Springs (1) Wheel If Equipped (2) Rear Lift Link Assemblies (1) Front Lift Link Assembly Keys (1) 3/4 O.D.
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY 4. SLIDE MOWER UNDER TRACTOR (See Fig. 8) • Bring belt forward and check belt for proper routing in all mower pulley grooves. NOTE: Be sure mower side suspension arms (A) are pointing forward before sliding mower under tractor. • Slide mower under tractor until it is centered under tractor. LIFT LEVER Fig. 4 2. ASSEMBLE FRONT GAUGE WHEEL (W) TO FRONT OF MOWER (See Fig. 5) H H. FRONT MOWER BRACKET W. FRONT GAUGE WHEEL X. SHOULDER BOLT Y. 1-1/4 O.D. WASHER Z. 3/8-16 LOCKNUT W X Z Q Y A.
ASSEMBLY ANTI-SWAY BAR (S) LOCATION 7. ATTACH REAR LIFT LINKS (C) (See Fig. 13) • Insert rod end of rear lift link (C) into hole (U) in tractor lift shaft suspension arm and pivot link down to mower. • Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with large washer and large retainer spring. • Repeat on opposite side of tractor. TRANSAXLE BRACKET (T) LOCATED BETWEEN REAR TIRES E TO HOL END IN ° 0 9 E PL AC U C C. REAR LIFT LINK(S) D.
ASSEMBLY ✓CHECKLIST 9 INSTALL BELT ON ENGINE CLUTCH PULLEY (M) (See Fig. 7 & 15) • Disengage belt tension rod (K) from locking bracket (L). • Install belt onto engine clutch pulley (M). BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions have been completed. ✓ No remaining loose parts in carton. ✓ Battery is properly prepared and charged.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P D G H E F B A M C J K L Fig. 16 Our tractors conform to the applicable safety standards of the American National Standards Institute. (H) LIGHT SWITCH - Turns the headlights on and off.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping may cause engine to “backfire”.
OPERATION • Put attachment lift lever in desired cutting height slot. The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. • The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months.
OPERATION TO STOP MOWER BLADES • TO OPERATE ON HILLS Disengage attachment clutch control. CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 23). • • • S • • • Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills.
OPERATION BEFORE STARTING THE ENGINE TO START ENGINE (See Fig. 16) When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Be sure freewheel control is in the transmission engaged position. • Sit on seat in operating position, depress brake pedal and set parking brake. • Move attachment clutch to “DISENGAGED” position. • Move throttle control to choke position.
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with o
MAINTENANCE TRACTOR CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty. Always observe safety rules when per form ing any maintenance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.
MAINTENANCE TRANSAXLE MAINTENANCE OIL DRAIN VALVE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials.
MAINTENANCE MUFFLER DECK WASHOUT PORT (See Fig. 31) Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig. 32) • • • TO REPLACE MOWER BLADE DRIVE BELT (See Fig.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see steps in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 36 & 37) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 38) Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest. BELT REMOVAL - G • Remove mower (See “TO REMOVE MOWER” section in this manual). NOTE: Observe entire motion drive belt and position of all belt guides and keepers. • • • Disconnect clutch wire harness (A). Remove anti-rotation link (B) on right side of tractor.
SERVICE AND ADJUSTMENTS TO CHECK BRAKE TO START ENGINE WITH A WEAK BATTERY (See Fig. 40) If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: • Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake. • Disengage transmission by placing freewheel control in “transmission disengaged” position.
SERVICE AND ADJUSTMENTS REPLACING BATTERY (See Fig. 41) TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 42) WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. • • • • • • • • • • • • Raise hood. Unsnap headlight wire connector. Stand in front of tractor.
STORAGE ENGINE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE.
TROUBLESHOOTING POINTS PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8.
TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 ELECTRICAL KEY NO. PART NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 CHASSIS KEY NO. 3 5 14 15 18 25 34 36 37 52 58 68 130 137 150 151 152 159 161 162 165 175 176 177 178 180 182 183 189 PART NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 DRIVE KEY NO. 1 2 15 17 26 29 33 35 42 49 50 51 52 56 64 73 80 92 99 116 125 143 153 159 160 161 163 166 167 170 183 PART NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 ENGINE KEY NO. PART NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 STEERING ASSEMBLY KEY NO. PART NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 SEAT ASSEMBLY 1 8 8 7 7 8 41 8 40 10 21 6 37 37 44 2 43 21 3 seat-tex_6.5SL_2 KEY PART NO. NO. DESCRIPTION 1 2 3 6 7 8 10 21 Seat Bracket Pivot Fender Strap, Asm Fender Nut, Lock W/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 unc x 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18 532 42 40-68 532 18 01-66 532 14 06-75 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 532 17 18-52 KEY PART NO. NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 MOWER LIFT 87 87 7 90 98 89 3 10 88 97 2 91 97 91 87 89 lift-tex_23 89 87 KEY PART NO. NO. DESCRIPTION 2 3 7 10 87 88 89 Shaft Asm., Lift Lever Lift Handle Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc 532 42 20-27 532 19 52-31 532 41 15-55 532 19 63-14 532 19 42-09 532 41 07-10 819 19 19-12 KEY PART NO. NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 MOWER DECK KEY NO. PART NO.
TRACTOR - - MODEL NUMBER YTH26V54 (96043011100), PRODUCT NO. 960 43 01-11 DECALS 2 5 6 2 3 1 9 4 8 7 12 KEY NO. PART NO. DESCRIPTION 1 2 3 4 5 6 7 8 532 41 16-57 532 42 91-96 532 44 05-70 532 43 50-97 532 42 38-29 532 43 84-80 532 17 05-63 532 17 84-55 Decal, Operators Decal, Badge Decal, Panel SD Decal, Eng. HP Decal, Customer Respons. Decal, Replacement Decal, Mower Caution Decal, Mower Caution PART NO.
&RQVXPHU :KHHOHG 3URGXFWV ± /LPLWHG :DUUDQW\ +XVTYDUQD ZDUUDQWV WR WKH RULJLQDO UHWDLO SXUFKDVHU WKDW WKLV +XVTYDUQD SURGXFW LV IUHH IURP GHIHFWV LQ PDWHULDO RU ZRUNPDQVKLS XQGHU QRUPDO XVH DQG PDLQWHQDQFH IURP WKH GDWH RI UHWDLO SXUFKDVH IRU WKH DSSOLFDEOH :DUUDQW\ 3HULRG VKRZQ RQ ([KLELW $ &HUWDLQ FRPSRQHQWV H J HQJLQHV DQG WUDQVPLVVLRQV DUH H[FOXGHG IURP FRYHUDJH DQG RWKHU OLPLWDWLRQV DSSO\ DV GHVFULEHG LQ WKLV GRFXPHQW +XVTYDUQD ZLOO UHSDLU RU UHSODFH DW LWV GLVFUHWLRQ DQ\ GHIHFWLYH SURG
F 3UHYHQWDWLYH PDLQWHQDQFH DV RXWOLQHG LQ WKH RSHUDWRU¶V PDQXDO ,Q DGGLWLRQ \RX PXVW FHDVH XVLQJ WKH SURGXFW LPPHGLDWHO\ XSRQ DQ\ IDLOXUH RU GDPDJH 7KH SURGXFW VKRXOG EH WDNHQ WR DQ DXWKRUL]HG +XVTYDUQD VHUYLFLQJ GHDOHU SULRU WR DQ\ IXUWKHU XVH 'DPDJHV UHVXOWLQJ IURP QRUPDO DJLQJ ZHDU DQG WHDU RU QHJOHFW DUH 127 FRYHUHG 7KH /LPLWHG :DUUDQW\ GRHV QRW FRYHU GDPDJH RWKHU WKDQ WKDW UHVXOWLQJ IURP GHIHFWV LQ PDWHULDO RU ZRUNPDQVKLS 7KH IROORZLQJ DUH 127 FRQVL
&RQVXPHU :KHHOHG :DUUDQW\ &KDUW ([KLELW $ &RQVXPHU SHUVRQDO KRXVHKROG XVH RQO\ 3URGXFW &RPSRQHQW 5LGLQJ /DZQ 7UDFWRUV )UDPH &KDVVLV )URQW $[OH (QJLQH 7UDQVPLVVLRQ LI PDGH E\ +XVTYDUQD 3HHUOHVV 7UDQVPLVVLRQ LI WKLUG SDUW\ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV 5HVLGHQWLDO =HUR 7XUQ 0RZHUV 5= 2QO\ (QJLQH 7UDQVPLVVLRQ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV 5HVLGHQWLDO =HUR 7XUQ 0RZHUV 0= (= (QJLQH 7UDQVPLVVLRQ %DWWHU\ 2WKHU 1RQ ([SHQGDEOH &RPSRQHQWV /( (GJHU (QJLQH 2WKHU 1RQ ([SHQGDEOH
&RQVXPHU :KHHOHG :DUUDQW\ &KDUW ([KLELW $ &RQVXPHU SHUVRQDO KRXVHKROG XVH RQO\ &RPPHUFLDO DQ\ FRPPHUFLDO 5HQWDO DQ\ UHQWDO SURIHVVLRQDO LQVWLWXWLRQDO XVDJH DULJFXOXWUDO RU LQFRPH SURGXFLQJ XVH RWKHU WKDQ 5HQWDO 8VH 3URGXFW &RPSRQHQW )URQW 0RXQWHG 'HFN 5LGHUV (QJLQH 7UDQVPLVVLRQ
SERVICE NOTES 49
SERVICE NOTES 50
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION FOL DA L O NG D THIS O I T S T A E D LIN 1 5 DEG E RE E S LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
11.16.10 JA Printed in the U.S.A.
