03002 LGT2554 Owner's Manual / 96043009400 / 2009-10 532 43 10-25
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. • Be alert and turn machine off if a child enters the area.
PRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIES Gasoline Capacity and type: 4 Gallons Unleaded Regular • • Oil Type (API-SG-SL): SAE 10W-30 (above 32°F) SAE 5W-30 (below 32°F) • Oil Capacity: W/ Filter: Spark Plug: Champion RC12YC (Gap: .030") Ground Speed (MPH): Forward: Reverse: Charging System: 15 AMPS @ 3600 RPM Battery: AMP/HR: MIN. CCA: Case Size: Blade Bolt Torque: 45-55 FT. LBS. 64 oz Read and observe the safety rules.
UNASSEMBLED PARTS Mower (5) Large Retainer Springs - 7/16 Mower Front Wheel (1) 3/4 O.D. Washers (1) Wheel (1) 1-1/4 O.D. Washer (2) Smaller Retainer Springs - 5/16 (5) 1-3/16 O.D.
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness. ADJUST SEAT (See Fig. 2) TOOLS REQUIRED FOR ASSEMBLY • • A socket wrench set will make assembly easier. Standard wrench sizes are listed.
ASSEMBLY INSTALL MOWER AND DRIVE BELT (See Figs. 4-12) NOTE: Be sure mower side suspension arms (A) are pointing forward before sliding mower under tractor. • Slide mower under tractor until it is centered under tractor. • FIRST INSTALL ANTI-SWAY BAR (S). - From right side of mower, insert anti-sway bar into hole in transmission bracket (T). Be sure tractor is on level surface and engage parking brake. • Lower attachment lift lever to it's lowest position. CAUTION: Lift lever is spring loaded.
ASSEMBLY • • • ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring. Repeat on opposite side of tractor. Turn steering wheel to position wheels straight forward. • • Disengage belt tension rod (K) from locking bracket (L). Install belt onto engine clutch pulley (M). M C D Fig. 11 IMPORTANT: Check belt for proper routing in all mower pulley grooves.
ASSEMBLY ✓CHECKLIST CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. P H D E G N B F Q C J A M Fig. 13 Our tractors conform to the applicable safety standards of the American National Standards Institute.
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR TRACTOR • TO SET PARKING BRAKE (See Fig. 14) • Your tractor is equipped with an operator presence sensing switch.
OPERATION TO ADJUST GAUGE WHEELS (See Fig. 19) TO MOVE FORWARD AND BACKWARD (See Fig. 17) Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Adjust gauge wheels with tractor on a flat level surface. • Adjust mower to desired cutting height (See “TO ADJUST MOWER CUTTING HEIGHT” in this section of manual).
OPERATION TO OPERATE ON HILLS TO STOP MOWER BLADES Disengage attachment clutch control. CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 20). • • • S • • • Choose the slowest speed before starting up or down hills. Avoid stopping or changing speed on hills.
OPERATION SERVICE REMINDER/HOUR METER TO START ENGINE (See Fig. 13) Service reminder shows the total number of hours the engine has run and flashes to indicate that the engine or mower needs servicing. When service is required, the service reminder will flash for two hours. To service engine and mower, see the Maintenance section of this manual. NOTE: Service reminder runs when the ignition key is in any position but "STOP".
OPERATION MOWING TIPS PURGE TRANSMISSION • CAUTION: Never engage or disengage freewheel lever while the engine is running. • To ensure proper operation and performance, it is recommended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have developed during shipping of your tractor.
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH USE EVERY 8 HOURS EVERY 25 HOURS EVERY 50 HOURS EVERY 100 HOURS EVERY SEASON BEFORE STORAGE Check Brake Operation T R A C T 0 R Check Tire Pressure Check Operator Presence & ROS Systems Check for Loose Fasteners Check/Replace Mower Blades 3 Lubrication Chart Check Battery Level 4 Clean Battery and Terminals Clean Debris Off Steering Plate Check Transaxle Cooling 5 Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with o
MAINTENANCE TRACTOR BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. Always observe safety rules when per form ing any maintenance. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.
MAINTENANCE V-BELTS OIL DRAIN VALVE Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. CLOSED AND LOCKED POSITION TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot.
MAINTENANCE IN-LINE FUEL FILTER (See Fig. 27) DECK WASHOUT PORT (See Fig. 29) The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. • With engine cool, remove filter and plug fuel line sections. • Place new fuel filter in position in fuel line with arrow pointing towards carburetor. • Be sure there are no fuel line leaks and clamps are properly positioned. • Immediately wipe up any spilled gasoline.
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. TO REMOVE MOWER (See Fig.
SERVICE AND ADJUSTMENTS TO LEVEL MOWER • If adjustment is necessary, see steps in Visual Adjustment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Fig. 34 and 35) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.
SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 36) TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1. Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake. 2. Disengage transmission by placing freewheel control in “transmission disengaged” position.
SERVICE AND ADJUSTMENTS TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 38) • TO REMOVE CABLES, REVERSE ORDER • BLACK cable first from chassis and then from the fully charged battery. • RED cable last from both batteries. The motion control lever has been preset at the factory and adjustment should not be necessary. • Loosen adjustment bolt in front of the right rear wheel, and lightly tighten. • Start engine and move motion control lever until tractor does not move forward or backward.
SERVICE AND ADJUSTMENTS TRANSMISSION INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting. • Check wiring. See electrical wiring diagram in the Repair Parts section. REMOVAL/REPLACEMENT Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMISSION” in the Operation section of this manual.
SERVICE AND ADJUSTMENTS Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. ENGINE FUEL SYSTEM IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE.
TROUBLESHOOTING PROBLEM Will not start CAUSE 1. 2. 3. 4. 5. 6. 7. CORRECTION Out of fuel. Engine not “CHOKED” properly. Engine flooded. Bad spark plug. Dirty air filter. Dirty fuel filter. Water in fuel. 1. 2. 3. 4. 5. 6. 7. Fill fuel tank. See “TO START ENGINE” in Operation section. Wait several minutes before attempting to start. Replace spark plug. Clean/replace air filter. Replace fuel filter. Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter. 8.
TROUBLESHOOTING PROBLEM CAUSE CORRECTION Engine continues to run when operator leaves seat with attachment clutch engaged 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. 2. 3. 4. 5. Worn, bent or loose blade. Mower deck not level. Buildup of grass, leaves, trash under mower. Bent blade mandrel.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 ELECTRICAL KEY NO. 1 2 8 16 21 22 24 25 26 27 28 29 30 33 34 40 41 42 43 46 50 55 59 71 79 90 91 92 93 94 99 100 103 PART NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 CHASSIS KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 DRIVE KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 ENGINE 1 22 87 21 20 81 82 62 18 84 45 15 69 37 69 12 28 70 71 11 37 79 91 29 41 2 42 85 9 SPARK ARRESTER KIT 90 Engine-tex_Kohl-2cyl_1_r3 KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 STEERING ASSEMBLY 26 45 51 1 21 63 19 16 60 57 63 9 61 8 7 66 67 2 59 98 7 6 4 35 58 64 67 28 13 22 15 6 14 5 69 68 62 13 14 15 53 8 70 steering-tex_LEGND2_18_r1 13 KEY NO. 1 2 4 5 6 7 8 9 13 14 15 16 19 21 22 26 28 35 45 PART NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 DECALS 4 16 17 16 1 14 14 9 8 3 2 KEY NO. 1 2 3 4 8 9 14 PART NO. 532 41 16-58 532 17 84-55 532 17 05-63 532 42 38-29 532 19 87-85 532 14 50-05 532 42 36-38 DESCRIPTION Decal, Fender Warning Decal, Mower Caution Decal, Warning Decal, Hood Cust Resp Decal, Mower Sch. Decal, Battery Dnge/Poi Decal, Panel Side WHEELS AND TIRES 1 2 11 3 4 7 10 5 6 9 8 KEY NO. 16 17 ---- PART NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 SEAT ASSEMBLY 1 8 8 8 7 7 8 41 40 10 21 6 37 6 37 2 44 43 21 3 seat-tex_6.5SL_3 KEY NO. 1 2 3 6 7 8 10 21 PART NO. 532 42 40-68 532 18 01-66 532 14 06-75 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 532 17 18-52 KEY NO. DESCRIPTION 37 40 41 43 44 Seat Bracket Pivot Fender Strap, Asm Fender Nut, Lock w/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 unc x 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18 PART NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 MOWER DECK KEY NO. PART NO.
TRACTOR - MODEL NO. LGT2554 (96043009400), PRODUCT NO. 960 43 00-94 MOWER LIFT 7 87 87 90 98 89 3 10 88 97 2 97 91 87 89 lift-tex_3 89 87 KEY NO. PART NO. DESCRIPTION 2 3 7 10 87 88 89 532 42 20-27 532 19 52-30 532 41 15-55 532 19 63-14 532 19 42-09 532 19 53-04 819 19 19-12 Shaft Asm., Lift Lever Asm., Lift RH Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc KEY NO. PART NO.
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 15 DEGREES MAX. WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. 1. Fold this page along dotted line indicated above. 2.
10.16.09 BAD/AP Printed in the U.S.A.
