Operator’s manual (EPA I, EPA II) 346XP 353 Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
KEY TO SYMBOLS Symbols on the machine: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Refuelling. Filing with oil and adjusting oil flow. The chain brake must be engaged when the chain saw is started.
CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ............................................. Symbols in the operator’s manual: ............................... CONTENTS Contents ...................................................................... INTRODUCTION Dear customer! ............................................................ WHAT IS WHAT? What is what on the chain saw? .................................. GENERAL SAFETY PRECAUTIONS Before using a new chain saw .............................
INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.
WHAT IS WHAT? Husqvarna XXX XXXX XXXXXXX Husqvarna AB Huskvarna, SWEDEN What is what on the chain saw? 1 Cylinder cover 16 Bumper spike 2 Front handle 17 Chain catcher 3 Chain brake and front hand guard 18 Clutch cover 4 Starter 19 Rear handle with right hand guard 5 Chain oil tank 20 Throttle control 6 Starter handle 21 Throttle lock 7 Adjuster screws carburetor 22 Decompression valve (Model 353) 8 Choke control/Start throttle lock 23 Combination spanner 9 Rear handle 24 Chain
GENERAL SAFETY PRECAUTIONS Before using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. Important IMPORTANT! The machine is only designed for cutting wood. • Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping. You should only use the saw with the bar and chain combinations we recommend in the chapter Technical data.
GENERAL SAFETY PRECAUTIONS chain saw usage if possible. Your dealer, forestry school or your library can provide information about which training materials and courses are available. • Fire Extinguisher and Shovel Generally clothes should be close-fitting without restricting your freedom of movement. IMPORTANT! Sparks can come from the muffler, the bar and chain or other sources. Always have fire extinguishing tools available if you should need them. Help prevent forest fires.
GENERAL SAFETY PRECAUTIONS • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism. • The brake is applied when the front hand guard (B) is pushed forwards. • • To release the chain brake pull the front hand guard backwards, towards the front handle. • Kickback can be very sudden and violent. Most kickbacks are minor and do not always activate the chain brake. If this happens you should hold the chain saw firmly and not let go.
GENERAL SAFETY PRECAUTIONS Will my hand always activate the chain brake during a kickback? if the bar and chain are properly serviced and maintained (see instructions under the heading General working instructions). No. It takes a certain force to move the hand guard forward. If your hand only lightly touches the front guard or slips over it, the force may not be enough to trigger the chain brake. You should also maintain a firm grip of the chain saw handles while working.
GENERAL SAFETY PRECAUTIONS Cutting hardwoods (most broadleaf trees) creates more vibration than cutting softwoods (most conifers). Cutting with cutting equipment that is blunt or faulty (wrong type or badly sharpened) will increase the vibration level. ! WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation. Contact your doctor if you experience symptoms of overexposure to vibration.
GENERAL SAFETY PRECAUTIONS Cutting equipment designed to reduce kickback ! WARNING! Faulty cutting equipment or the wrong combination of bar and saw chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data. • Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.
GENERAL SAFETY PRECAUTIONS • The cutting part of the chain is called the cutter and consists of a cutting tooth (A) and the depth gauge (B). The cutters cutting depth is determined by the difference in height between the two (depth gauge setting). Sharpening cutting teeth To sharpen cutting teeth you will need a round file and a file gauge. See instructions under the heading Technical data for information on the size of file and gauge that are recommended for the chain fitted to your chain saw.
GENERAL SAFETY PRECAUTIONS Adjustment of depth gauge setting • • • The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively. • Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.
GENERAL SAFETY PRECAUTIONS Filling with chain oil • All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable. • The saw chain oil tank and the fuel tank are designed so that the fuel runs out before the saw chain oil.
GENERAL SAFETY PRECAUTIONS When the length of the cutting teeth has worn down to only 4 mm (0,16 inch) the chain must be replaced. Bar Check regularly: • Whether there are burrs on the edges of the bar. Remove these with a file if necessary. • Whether the groove in the bar has become badly worn. Replace the bar if necessary. • Whether the tip of the bar is uneven or badly worn. If a hollow forms on the underside of the bar tip this is due to running with a slack chain.
ASSEMBLY Fitting the bar and chain ! Tension the chain by turning the chain tensioning screw clockwise using the combination spanner. See instructions under the heading Tensioning the chain. WARNING! Always wear gloves, when working with the chain, in order to protect your hands from injury. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle.
FUEL HANDLING Fuel Mixing ratio Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and twostroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.
FUEL HANDLING • In temperatures below 0°C (32°F) some oils become too viscous. This can overload the oil pump and result in damage to the oil pump components. • Contact your service agent when choosing chain oil. • Move the machine at least 3 m from the refuelling point before starting it. • Never start the machine: 1 If you have spilt fuel or chain oil on the machine. Wipe off the spillage and allow remaining fuel to evaporate.
STARTING AND STOPPING Starting and stopping ! WARNING! Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Warm engine Use the same procedure as for starting a cold engine but without setting the choke control in the choke position. The correct choke/start throttle setting is obtained by moving the choke control to the choke position and then pushing it in again.
STARTING AND STOPPING Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is ready for use. ! • Always hold the saw with both hands. The right hand should be on the rear handle, and the left hand on the front handle. All people, whether right or left handed, should use this grip. Use a firm grip with thumbs and fingers encircling the chain saw handles.
WORKING TECHNIQUES Before use: • To make sure that none of the above might come within reach of your saw or be injured by falling trees. , 1 Check that the chain brake works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle lock works correctly and is not damaged. 4 Check that the stop switch works correctly and is not damaged. 5 Check that all handles are free from oil.
WORKING TECHNIQUES Have control over the workpiece. 6 7 If the pieces you intend to cut are small and light, they can jam in the saw chain and be thrown towards you. Even if this does not need to be a danger, you may be surprised and lose control of the saw. Never saw stacked logs or branches without first separating them. Only saw one log or one piece at a time. Remove the cut pieces to keep your working area safe.
WORKING TECHNIQUES 9 Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting with a pulling chain. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting with a pulling chain gives the operator better control over the chain saw and the position of the kickback zone. 2 Make sure the object you are cutting will not split.
WORKING TECHNIQUES Cutting ! The log is supported at one end. There is a high risk that it will split. WARNING! Never attempt to cut logs while they are in a pile or when a couple of logs are lying together. Such procedures drastically increase the risk of kickback which can result in a serious or fatal injury. If you have a pile of logs, each log you attempt to cut should be removed from the pile, placed on a saw horse or runners and cut individually. Remove the cut pieces from the cutting area.
WORKING TECHNIQUES Felling direction Clearing the trunk and preparing your retreat The aim is to fell the tree in a position where you can limb and cross-cut the log as easily as possible. You want it to fall in a location where you can stand and move about safely. Delimb the stem up to shoulder height. It is safer to work from the top down and to have the tree between you and the saw. Once you have decided which way you want the tree to fall you must judge which way the tree would fall naturally.
WORKING TECHNIQUES Next make the bottom cut so that it finishes exactly at the end of the top cut. opposite direction to your intended felling direction. Drive a wedge or breaking bar into the cut as soon as it is deep enough. The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°. Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter.
WORKING TECHNIQUES We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommended for your saw. • Portable Cutting trees and branches that are in tension Preparations: Work out which side is in tension and where the point of maximum tension is (i.e. where it would break if it was bent even more).
WORKING TECHNIQUES How to avoid kickback ! WARNING! Kickback can happen very suddenly and violently; kicking the chain saw, bar and chain back at the user. If this happens when the chain is moving it can cause very serious, even fatal injuries. It is vital you understand what causes kickback and that you can avoid it by taking care and using the right working technique.
MAINTENANCE General Basic settings and running in The user must only carry out the maintenance and service work described in this manual. The basic carburetor settings are adjusted during testing at the factory. Avoid running at a too high speed for extended periods during the first 10 hours. IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer (retailer).
MAINTENANCE When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance. The carburetor’s high speed jet is then locked using a limiter cap in the fully screwed out position. The limiter cap limits the potential to adjust the high speed jet to at most half a turn. Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.
MAINTENANCE Apply full throttle and activate the chain brake by tilting your left wrist forward onto the front hand guard. Do not let go of the front handle. The chain should stop immediately. Right hand guard Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. Throttle lock • Make sure the throttle control is locked at the idle setting when the throttle lock is released.
MAINTENANCE Muffler Starter ! Never use a machine that has a faulty muffler. WARNING! When the recoil spring is wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury. Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves. Changing a broken or worn starter cord Regularly check that the muffler is securely attached to the machine.
MAINTENANCE Tensioning the recoil spring • Air filter Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise. Note! Check that the pulley can be turned an additional 1/ 2 turn when the starter cord is pulled all the way out. Changing a broken recoil spring • Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the starter housing.
MAINTENANCE Spark plug Adjustment of the oil pump The spark plug condition is influenced by: The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow. • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil).
MAINTENANCE Note! The cooling system on a chain saw with catalytic converter must be cleaned daily. This is particularly important on chain saws with catalytic converters, because the higher exhaust temperature requires efficient cooling of the engine and the catalytic converter unit. • a winter plug (B) for the air nozzle that is fitted as shown. ”Air Injection” centrifugal cleaning Centrifugal cleaning means the following: All air to the carburetor passes through the starter.
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Clean the outside of the machine. Weekly maintenance Monthly maintenance On chain saws without a catalytic converter, check the cooling system weekly. Check the brake band on the chain brake for wear. Replace when less than 0.6 mm (0,024 inch) remains at the most worn point.
TECHNICAL DATA Technical data 346XP 353 Cylinder displacement, cu.
TECHNICAL DATA Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the Husqvarna chain saw models 346XP and 353. The combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and vibration requirements of ANSI B 175.1–2000. The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a hard nose.
FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800-487-5963. The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. In U.S.
AMERICAN STANDARD SAFETY PRECAUTIONS Safety precautions for chain saw users (ANSI B 175.1-2000 Annex C) Kickback safety precautions ! Other safety precautions ! WARNING! Do not operate a chain saw with one hand! Serious injury to the operator, helpers, bystanders or any combination of these persons may result from one-handed operation. A chain saw is intended for twohanded use.
´®z+R$o¶59¨ ´®z+R$o¶59¨
1150047-95 ´®z+R$o¶59¨ ´®z+R$o¶59¨ 2005-01-13