130SB Owner's Manual / 96193004300 / 2008-11
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have exposed rotating parts, which can cause severe injury from contact, or from material thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.
Clearing a Clogged Discharge Chute 6. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine. 7. Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous. 8.
PARTS PACKED SEPARATELY IN CARTON (1) AUGER CONTROL ROD (1) TRACTION DRIVE CONTROL ROD (1) SAFTEY IGNITION KEY (35062) (1) POWER CORD (198563) (1) MULTIWRENCH (180684) (1) DISCHARGE CHUTE EXTRA SHEAR BOLTS AND NUTS (6) SHEAR BOLTS 1/4-20 x 1-3/4 (198636) (6) SPACERS (198638) (6) LOCKNUTS 1/4-20 (73800400) ROTATOR HEAD MOUNTING (2) HANDLE KNOBS (3) RETAINER SPRINGS (169675) (1) WASHER 3/8 (19131316) (2) CARRIAGE BOLTS 3/8-16 x 2.
ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates. INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown. 2.
ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 2. With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring. INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig.
ASSEMBLY / PRE-OPERATION INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely. 3. Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning.
OPERATION SAFETY IGNITION KEY SPARK PLUG AUGER CONTROL LEVER ENGINE OIL CAP WITH DIPSTICK GASOLINE FILLER CAP DISCHARGE CHUTE CONTROL LEVER DEFLECTOR TRACTION REMOTE DRIVE SPEED DRIVE CONTROL CONTROL LEVER CONTROL LEVER LEVER CHUTE DEFLECTOR CHOKE CONTROL FUEL SHUT-OFF VALVE LH TURN TRIGGER THROTTLE / ENGINE CONTROL DISCHARGE CHUTE POWER CORD PLUG ELECTRIC START BUTTON RECOIL STARTER HANDLE LIGHT OIL DRAIN PLUG HANDLE KNOB CLEAN-OUT TOOL PRIMER MUFFLER NOTE: ITEMS ABOVE ARE SHOWN IN THEIR T
OPERATION The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any adjustments or repairs. We recommend standard safety glasses or a wide vision safety mask worn over spectacles. TO USE CHOKE CONTROL (See Fig. 13) The choke control is located on the engine. Use the choke control whenever you are starting a cold engine.
OPERATION TO MOVE FORWARD AND BACKWARD (See Fig. 17) SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to engage the drive system. • Release traction drive control lever to stop the forward or reverse movement of the snow thrower. SPEED and DIRECTION are controlled by the drive speed control lever.
OPERATION BEFORE STARTING THE ENGINE TO ADJUST SKID PLATES (See Fig. 19) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions.
OPERATION 6. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the OFF position. DO NOT push the primer. TO START ENGINE • Be sure fuel shut-off valve is in the OPEN position. Your snow thrower engine is equipped with both a 120 Volt A.C.
MAINTENANCE GENERAL RECOMMENDATIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your snow thrower. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual.
MAINTENANCE BELTS Check belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual). The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer.
SERVICE AND ADJUSTMENTS WARNING: To avoid serious injury, before performing any service or adjustments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key. 3. Make sure the augers and all moving parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. SNOW THROWER TO ADJUST SNOW THROWER HEIGHT See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual. 1.
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 24) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center. NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.
TO REMOVE WHEELS (See Fig. 25) • Remove the klik pin and remove wheel from axle. IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower. KLIK PIN (INSTALL IN OUTER HOLE OF AXLE ONLY) OUTER HOLE AXLE WHEEL WHEEL HUB FIG.
TROUBLESHOOTING See appropriate section in manual unless directed to a qualified service centre. PROBLEM Does not start CAUSE 1. Fuel shut-off valve (if so equipped) in OFF position. 2. Safety ignition key is not inserted. 3. Out of fuel. 4. Throttle in STOP position. 5. Choke in OFF position. 6. Primer not depressed. 7. Engine is flooded. 8. Spark plug wire is disconnected. 9. Bad spark plug. 10. Stale fuel. 11. Water in fuel. CORRECTION 1. Turn fuel shut-off valve to OPEN position. 2.
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 5 11 11 6 7 15 14 16 12 13 8 11 4 12 3 17 10 11 1 9 2 33 32 34 30 31 31 26 36 29 28 27 23 22 21 20 25 35 24 23 22 2 (EXPLODED) 21 18 19 01.07.
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 KEY NO. PART NO.
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 1 3 (5x) KEY NO. PART NO. DESCRIPTION 1 2 3 4 532 40 77-21 532 40 76-45 872 27 05-05 532 15 53-77 AUGER HOUSING SCRAPPER BAR CARRIAGE BOLT 5/16−18 X .625 NUT 5/16−18 KEY NO. PART NO. DESCRIPTION 1 2 532 40 77-23 532 40 77-22 AUGER 30 LH AUGER 30 RH 4 (5x) 2 01.07.003-A 1 2 01.07.013-A NOTE: All component dimensions given in U.S. inches. 1 inch = 25.
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 1 3 2 2 1 KEY NO. 1 2 3 3 PART NO. 532 18 79-25 532 18 81-70 532 17 95-82 DESCRIPTION AUGER BALL BEARING PLASTIC RETAINER SCREW 5/16−18 X 1.00 01.07.006-A 2 3 1 3 2 KEY NO. 1 2 3 01.11.002-A PART NO. 532 40 78-34 872 27 05-06 532 75 11-53 DESCRIPTION SKID PLATE CARRIAGE BOLT 5/16−18 X .750 NUT 5/16−18 1 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.
REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 1 4 5 1 3 4 3 4 3 KEY NO. PART NO. DESCRIPTION 1 2 3 4 5 532 18 47-47 872 27 05-06 532 17 92-46 810 04 05-00 532 12 86-38 DRIFT CUTTER BAR CARRIAGE BOLT 5/16−18 X .750 PLASTIC WASHER LOCKWASHER 5/16 NUT 5/16−18 KEY NO. PART NO. DESCRIPTION 1 2 532 18 25-16 872 11 05-10 3 4 532 75 11-53 819 11 22-06 5 3 2 2 4 01.16.
REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 5 7 3 14 15 *13 *10 *9 2 KEY NO. PART NO.
REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 2 2 1 *3 *6 *6 KEY NO. PART NO. DESCRIPTION 1 2 *3 *4 *5 *6 532 42 03-37 817 50 10-10 532 42 06-78 532 42 11-61 532 42 06-75 532 42 11-62 LEVER/CABLE ROTATOR ASSEMBLY GRAY SCREW 10−24 X .625 ROTATOR HEAD ROTATOR PIVOT BRACKET PULLEY PIVOT CABLE ASSEMBLY GRAY *4 01.09.007-A *5 NOTES: 1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY. 2 1 KEY NO.
REPAIR PARTS HANDLES SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 3 4 3 4 4 1 3 KEY NO. PART NO. DESCRIPTION 1 2 3 4 532 42 11-20 532 42 11-21 874 78 05-24 532 75 11-53 LOOP HANDLE LH LOOP HANDLE RH SCREW 5/16−18 X 1.50 NUT 5/16−18 KEY NO. PART NO. DESCRIPTION 1 2 3 4 532 42 10-59 532 41 54-89 817 00 05-12 817 00 06-16 LOWER TUBE PIVOT SUPPORT BOLT 5/16−18 X .750 SCREW 3/8−16 X 1.00 4 3 2 01.08.004-B 1 2 4 3 4 4 4 3 01.05.
REPAIR PARTS HANDLES SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 10 2 11 8 6 7 9 9 7 4 5 1 3 13 8 12 13 14 14 01.08.002-E 12 KEY NO. PART NO.
REPAIR PARTS HANDLES SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 10 2 10 1 3 9 8 5 4 7 18 5 18 18 17 19 KEY NO. PART NO.
REPAIR PARTS HANDLES SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 4 3 2 5 1 6 KEY NO. PART NO. DESCRIPTION 1 2 3 4 5 6 532 41 62-88 532 41 45-72 532 17 88-31 532 16 96-75 817 06 04-10 532 42 18-14 INTERLOCK SPRING INTERLOCK CAM TORSION SPRING RETAINER SCREW 1/4−20 X .625 INTERLOCK STOP KEY NO. PART NO.
REPAIR PARTS DRIVE SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 24 23 27 3 21 25 1 28 28 27 14 26 28 28 1 16 2 2 14 1 3 1 15 2 20 3 2 17 11 8 8 14 13 2 12 1 2 22 2 2 1 18 19 10 9 8 1 4 7 4 5 6 2 1 3 4 5 KEY NO. PART NO. 1 2 3 4 5 6 7 8 9 817 49 05-08 532 75 11-53 532 18 00-17 873 93 05-00 532 19 95-09 532 17 98-31 532 17 86-13 874 76 05-14 532 17 53-44 10 11 12 13 812 00 00-12 532 18 00-66 532 18 00-65 532 19 29-07 01.02.
REPAIR PARTS DRIVE SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 2 2 1 42 20 43 41 40 32 32 20 41 38 3 37 39 7 4 36 5 6 12 7 35 34 29 15 31 8 9 14 15 7 28 32 10 11 13 15 14 33 30 17 15 26 8 16 23 17 18 19 27 20 21 44 22 25 01.02.
REPAIR PARTS DRIVE SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 KEY NO. PART NO.
REPAIR PARTS DRIVE SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 6 7 1b 4 8 3 1b 7 1a 2 3 5 4 6 01.03.001-A KEY NO. PART NO. DESCRIPTION 1 1a 1b 2 3 4 5 6 7 8 532 40 49-23 532 40 43-07 532 18 42-06 532 18 00-81 532 17 46-97 532 17 98-30 532 14 63-15 817 49 05-08 532 15 54-43 532 18 92-82 (assy of 1a,1b) AXLE ASSEMBLY AXLE SHAFT ROLL PIN 3/16 GEAR THRUST WASHER AXLE BEARING SCREW 5/16−18 X .625 BOLT 5/16−18 X .
REPAIR PARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 3 1 3 4 4 01.00.018-A 2 KEY NO. PART NO. - ------ 1 2 3 4 532 41 61-55 532 41 08-77 532 15 04-06 532 18 44-71 ENGINE TEC MODEL OH318SA-221807B FRAME BOTTOM PAN BOLT 3/8−16 SCREW 10−24 X .625 KEY NO. PART NO. DESCRIPTION 1 2 3 4 532 40 91-61 532 17 88-13 532 41 97-44 532 40 80-08 COVER ASSEMBLY PULLEY TRACTION BELT IMPELLER BELT DESCRIPTION 1 2 3 01.04.
REPAIR PARTS WHEELS SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 1 KEY NO. PART NO. DESCRIPTION 1 2 532 19 94-99 532 19 95-00 WHEEL 16 X 4.80 X LH WHEEL 16 X 4.80 X RH KEY NO. 1 2 PART NO. 532 41 52-63 532 18 78-59 DESCRIPTION STEER CABLE BRACKET LH STEER CABLE BRACKET RH 2 01.06.005-A 1 2 01.15.002-A NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
REPAIR PARTS WHEELS SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 2 17 20 16 18 15 18 24 17 16 20 19 2 3 2 1 4 5 6 11 21 21 7 8 9 7 22 23 22 11 10 4 23 19 14 12 13 13 14 10 9 6 3 5 8 12 01.15.001-A KEY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PART NO.
REPAIR PARTS BAG OF PARTS SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 4 14 13 6 5 12 9 8 3 10 2 11 7 KEY NO. PART NO.
REPAIR PARTS DECALS SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43 1 2 4 9 12 6 1 3 5 10 KEY NO. PART NO.
532 42 52-72 Rev.1 11.11.08 SR Printed in the U.S.A.
