Owner Manual

ManualsBrandsHUSKY ManualsAll VacuumsHUSKY Flair Central Bagless Upright Vacuum

Th i s Ce n T r a l Va C u u m sy s T e m h a s b e e n

d e s i g n e d b y nu e r a ai r a n d b u i l T w i T h

s p e C i a l i s e d m a T e r i a l s o f T h e h i g h e s T

q u a l i T y .

iT i s T h e r e f o r e i m p o r T a n T T o f o l l o w T h e

i n s T a l l aT i o n i n s T r u C T i o n s i n o r d e r T o

b e n e f i T f r o m a l l T h e a d V a n T a g e s T h a T y o u r

n e w s y s T e m p r o V i d e s .

PIPING

INSTALLATION

INSTRUCTIONS

f o r a c e n t r a l v a c u u m s y s t e m

Summary of content (10 pages)

PAGE 1
Piping Installation Instructions for a central vacuum system This Central Vacuum System has been designed by Nuera Air and built with specialised materials of the highest quality. It is therefore important to follow the installation instructions in order to benefit from all the advantages that your new system provides.
PAGE 2
PAGE 3
Table of Contents Safety Rules �� 14 Fire protection �� 14 Safety Equipment ��
PAGE 4
1. Safety Rules Piping installation for a central vacuum system is not complicated. All that is required is to have a few hand tools and to read the instructions carefully. However, it is essential to do the installation carefully and safely. We recommend that you read the next few lines with the greatest attention. Inspection of Power Unit The Power Unit and all connections should be inspected before starting and at regular intervals to ensure normal, reliable and safe operation.
PAGE 5
2. Planning Installing the piping for a central vacuum system does not require specialized tools and can be done by anyone. However, it is important to take time to plan the installation carefully. Be sure to check the positioning of inlets several times, in relation to furniture, the length of the hose and the components that will be inside the wall.
PAGE 6
Use the following method to check the location of vacuum inlets: The garage If structurally possible, install a vacuum inlet close to the door to increase the reach of the hose outside during the summer. Piping • Simulate cleaning each room using the hose. To do this, ask an assistant to hold the end of the hose at the point where you have assessed the inlet location. Walk around with it to cover the entire area, including the corners at the ceiling.
PAGE 7
pipe immediately, reapply adhesive and try again; 4. Wipe off adhesive with a rag and let stand for 2 minutes making sure that the connection stays in place. 5. Allow to dry for 3 hours before use. * * Ensure that low voltage wires do not come into contact with another current source, which could result in electrocution. * Jacketed low voltage wiring? WARNING! * CAUTION! Extremely flammable. Keep away from open flame and sparks. Use only in a well ventilated area. KEEP OUT OF REACH OF CHILDREN.
PAGE 8
This connection is multipurpose. When used with a 45° Elbow, two parallel pipes can be connected together. TUY-29 45° Wye TUY-44 Cap To terminate a line of pipe, use only a cap. IMPORTANT! Other means of capping a pipe may damage the Power Unit when starting or create an obstruction if the cap enters the piping. * TUY-28 Double 45° Wye This connection combines two 45° elbows to make two branches at 90° from the main line.
PAGE 9
d. Attach the wires to the inlet using a Philips screwdriver. 5. Install the vacuum inlet onto the mounting plate a. Insert the mounting plate in the opening and hold it in place on the inner wall. Do not let go! IMPORTANT! The front face of the mounting plate must not be above the finished wall surface! * The front face of the mounting plate must be a few millimeters inside the finished wall surface! b. Pass a piece of bent coat hanger into the inlet then into the mounting plate.
PAGE 10
03 / 10 DOC-376_EN