www.HunterFan.com Table of Contents Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. WARNINGS If you are unfamiliar with wiring, use a qualified electrician. 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3592-01 • 12/14/15 • © 2015 Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M3592-01 • 12/14/15 • © 2015 Hunter Fan Company 1.888.830.
Wiring OM FR Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. CEILIN www.HunterFan.com Not for use in applications where the fan does not have a wall switch. G OM FR G T KE FR Black M FA N (Ungrounded) FRO Blue AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 10 M3592-01 • 12/14/15 • © 2015 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Put the blade washers found in the hardware bag onto the blade screws found in the hardware bag. Then install the blade screws to secure each blade to a blade iron. 11 M3592-01 • 12/14/15 • © 2015 Hunter Fan Company 1.888.830.
www.HunterFan.com Light Kit Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Wrap keyhole slots around the screws and twist counterclockwise. 12 M3592-01 • 12/14/15 • © 2015 Hunter Fan Company 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 CONGRA YOU’RETULATIONS! DONE! Connect the white wire from the fan to the white wire from the light kit. Then, connect the blue wire from the fan to the black wire from the light kit. Lift the globe and align the notches in the globe with the tabs in the light kit. Attach the globe by lifting and twisting counterclockwise until it rests firmly in place.
www.HunterFan.com Remote Control Battery Door 1.888.830.1326 r we o nP r Tu ON Phillips Head Screw The remote transmitter is already paired to the receiver and ready to use. To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. Note: If your need to pair your remote, remove the battery door.
www.HunterFan.com Remote Control Cradle 1.888.830.1326 You have two options to install the included remote control cradle to the wall. Choose which path works best for you. Option 1: Using Screws Option 2: Using Adhesive Strip Choose your cradle installation location. Remove the cradle from the cradle bracket. If you are installing into drywall, drill two 9/64 width holes using the cradle bracket as a guide. Gently hammer the included drywall anchors into the pre-drilled holes.
Operation, Maintenance, and Cleaning www.HunterFan.com 1.888.830.1326 Light Button Fan Button Fan Control Fan Operation: Press and quickly release the fan button on the remote control to turn the fan OFF or ON. Use the fan control directional pad to raise or lower the fan to the desired speed Light Operation: Press and quickly release the light button on the remote control to turn the light OFF or ON. Press and hold the light button for continuous dim.
www.HunterFan.com 1 1.888.830.1326 Download the app: Visit your app store and search simpleconnect to find the app. 2 Launch the app. 3 Follow the onscreen prompts to set up your fan. Note: The HomeKit identification number is located on the front cover of the English side of the Parts Guide. SIMPLEconnect connects to available 2.4 GHZ WiFi networks.
www.HunterFan.com Troubleshooting 1.888.830.1326 Fan doesn’t work Excessive wobbling Noisy Operation Wireless Issues • Make sure power switch is on. • Make sure the blades are properly installed on the blade iron posts. • Make sure the blades are properly installed on the blade iron posts. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated. • Check to see if any of the blades are cracked. If so, replace all of the blades.