civics 8 QoL) J] SOCIOPOLITICAL SO BIB] CTs [venue Installation and Operation Manual for Hunter Ceiling Fans
For Your Records and Warranty Assistance Model Name: Catalog/Model No: Serial No: Date Purchased: ‘Where Purchased: For reference also attach your receipt or a copy of your receipt to he manual. Table of Contents 1s Getting Ready. 2+ Installing the Ceiling 3+ Assembling the Fan 4a Installing the Blade Iron: 5 « Hanging the Fan 6 + Wiring the Fan 7 « Installing the Canopy and Canopy Trim Ring... 8 » Installing the Blades... 9 « Installing the Light 10 « Installing the Wall Contra...
Getting Ready Installing Multiple Fans? If you are installing more than one fan, keep the fan blades in sets, as they were shipped. To install a ceiling fan, be sure you can do the following: « Locate the ceiling joist ar other suitable support in ceiling. + Drill holes for and install wood screws, » Identify and connect electrical wires. « Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician.
«A aan ay | Young assemble your fan for standard scrounging {steps for low profile mounting (steps 3:3 + 3:4), Tor install the remote celerity you will heed £5 strip electrical wires, If you are uncomfortable doing so, seek help from qualified electrician. [Sidestep «33 | — Down rod — Canopy 340. To assemble Fate hang down from a flavor angled ceiling, insert the breakthrough the canopy and:canopy trim ring. Feed the wires from the fan through the down rod, QF iin ; . tee 3:2.
« Installing the Blade Irons ) 41. Blade Iron “Two Notches for Screws Shipping Blocks Turn the fan upside down. Use the ceiling fan package to support + the fan while assembling the blade irons. 42. 43, 44. 4-5, 4-6. 4-7. Loosen all of the blade iron assembly screws. Do not completely remove the screws. Remove and discard all of the shipping blocks, Slide the blade iron under the switch housing plate, aligning the two notches with the two blade iron assembly screws.
Receiver Wire Nut All wiring must be in accordance with national and local electrical codes and EXPANSION 70. If you are unfamiliar with wiring, use a qualified electrician, 6-1. Disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. 6-2. To connect the wires, hold the bare metal leads together and place 2 wire nut over them, then twist clockwise until tight. For all these connections use the larger wire nuts provided.
Our exclusive Easy Lock™ blade assembly enables you to lock the blades in place without tools and to remove the blades easily for cleaning. 8-1. Open the locking mechanism. 8-2. Align the holes in the blade with the blade iron. 8-3. Close the locking mechanism securely. You will feel it lock into place. Hunter Fan Company 41868-01 « 02/20/04 REEL TPR TY BFS TCT The French Quarter comes with the Easy-to-Install “Plug-in” Light Fixture.
rallying the Wall Control A Steps 10-1 ~ 10-4 Wire Nut Steps 10-5 ~ 10-8 The wall control is optional. You can install it in addition to using the remote transmitter, but you do not need to install both in order for the fan to work. 10-1. 10-2, 10-3. 10-4. 10-5, 10-6. 10-7. 10-8. 10-9. 10-10. Turn circuit breaker to the fan wall switch OFF. Remove the wall plate and switch.
Reversing Switch ™ Down Dimmer Steps 12-1-12-5 Step 12-6 Up Dimmer 12-1. The remote transmitter has four numerical buttons: 0=0f 1= Low speed 2 = Medium speed 3 = High speed 12-2. For best operation, start the fan by pressing 3 (high), and then select your desired speed. 12-3. The reversing switch reverses the direction of the fan, 12-4. The up dimmer turns the light on and can be used to increase the brightness if the light is already on. 12-5. The down dimmer turns the light off.