User's Manual

ManualsBrandsHunter Fan ManualsElectronicsCeiling fan and lamp remote control.

Hunter Fan Company

Remote Ceiling Fan &

Light Control

Transmitter Model: 84592

Transmitter Battery: 12 V, Type 23A, MN-21 or equivalent

Receiver Model: 85068

Ratings: 120 VAC, 60 Hz, 1.0 Amp Fan

300 Watts incandescent light

Read and Save these Instructions

Caution: Risk of Electrical Shock!

All wiring must be performed in accordance with national and

local electrical codes. If you are unfamiliar with the wiring

codes, you should use a qualified electrician.

To avoid over heating and possible damage to other equipment,

do not install to control a receptacle, fluorescent light fixture,

motor operated appliance, or transformer-supplied appliance.

Use only to control one paddle-blade ceiling fan and

incandescent light fixture.

Notes:

1. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2)

this device must accept any interference received, including

interference that may cause undesired operation.

2. This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Note: Any changes or modifications to the transmitter or

receiver not expressly approved by Hunter Fan Company

may void one’s authority to operate this remote control.

3. For use only with electrically reversible ceiling fans rated

at 1.0 amp or less, and fan incandescent light kits rated at

300 watts or less.

4. Not for use with shaded-pole or nonreversible motors. Not

recommended for use with the Hunter Original®.

Before Installing the Control:

1. Use the pull-chain switch to set the fan speed to the HIGH

position before installation.

Note: Do not use the pull-chain to change the fan speed

after installation, as damage to your ceiling fan or control

may result. The speed of the fan should only be changed

by the control.

2. Set the ceiling fan light kit to the ON position before

installation. The light level should only be changed by the

control.

Receiver Installation:

1. Disconnect the power to the ceiling fan and light kit at the

main electric panel. Remove fuse or move circuit breaker

to the OFF position. Turn off wall switch.

2. IMPORTANT! Before installing this control, change the

factory default jumper switch settings to your own unique

code. Refer to Figure 1. Using small pliers or tweezers,

pull out one or more of the three jumper switches by

clamping on the small metal strip. Place the jumper

switches in the desire spots. Be sure the jumper switch

positions of the transmitter and receiver match, or the

ceiling fan will not function. Select different combinations

of jumper switches to prevent misoperation due to other

remote control fans, garage door openers, etc.

Figure 1 - Jumper Switches

3. Install the ceiling fan according to its instructions, up to

the point of making the electrical connections.

Note: When installing this remote control on the fan, be

sure to cut and strip the fan leadwires to leave 6 1/2”

outside of the hanger pipe.

4. Use the two large wire nuts supplied to connect the receiver

and house wiring, then use the three small wire nuts

supplied to connect the receiver and ceiling fan wiring.

Refer to the Wiring Diagram in Figure 2.

Figure 2 - Wiring Diagram

5. Install receiver as shown in Figure 3. Line up the slots on

the receiver with the ceiling plate. Be sure to push wire

connections from the ceiling back up through the hole in

the ceiling plate. Wires attaching from the ceiling plate to

the fan should be placed inside the canopy under the

Transmitter

Back

Jumper

Switch

Jumper

Switch

Receiver

Back

Light

Kit

Fan Common

Antenna

120 V AC

Power In

Black Main

White Main

WhiteBlackBlack/

White

Summary of content (4 pages)

PAGE 1
2. Set the ceiling fan light kit to the ON position before installation. The light level should only be changed by the control. Hunter Fan Company Remote Ceiling Fan & Light Control Receiver Installation: Transmitter Model: 84592 Transmitter Battery: 12 V, Type 23A, MN-21 or equivalent Receiver Model: 85068 Ratings: 120 VAC, 60 Hz, 1.0 Amp Fan 300 Watts incandescent light 1. Disconnect the power to the ceiling fan and light kit at the main electric panel.
PAGE 2
receiver. Once the receiver is installed, continue with the appropriate instructions from the fan installation manual to finish installing the fan. the fan does not start or is turning too slow, turn off the power at the wall switch. Pull the fan’s pull chain to change speed. Reapply power and try HIGH speed again. Repeat this procedure until you have confirmed that the fan’s pull chain is set to HIGH speed. Ceiling Plate Receiver Operation: 1.
PAGE 3
Troubleshooting Symptom Possible Causes Solution 1. No functions operate. Main Power not restored. Replace fuse. Turn ON circuit breaker. Turn ON wall switch. Fan pull chain not set to HIGH. Turn OFF power at wall switch or main electric panel. Set fan to HIGH speed. Light pull chain not set to ON. Set light kit to ON. Receiver wiring incorrect. Verify wiring connections. Transmitter and receiver jumper switches do not match. Set transmitter and receiver to same jumper switch setting.