Rhein Tech Laboratories, Inc. 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com Appendix I: Client: Hunter Engineering Company Model: 146-59-1 Standards: FCC 15.247/IC RSS-210 ID’s: LS3-146591/2938A-146591 Report #: 2015070 Manual Please refer to the following pages.
Form 6754-T, 05-15 Supersedes Form 6754-T, 12-13 SETUP INSTRUCTIONS FOR REMOTE CONTROL 146-57-1 & 146-59-1 This procedure should be performed only by an authorized factory representative. This document provides information for installation and setup of the XF remote controller. Second generation remotes require a different procedure to set the wireless channel. 146-59-1 146-57-1 Figure 1. CONSOLE CHANNEL SELECTION In most cases, the wireless channels should be correctly set from the factory.
2. Wireless channels in use will be displayed. Press “Scan Channels” to identify channels that are in use. Select the desired channel, then select “Set Channel”. Figure 3. Set the channel of the remote if necessary as follows. SECOND DESIGN (146-59-1) SETTING THE REMOTE CHANNEL The wireless channel is selected using a set of dip switches on the main board. To set the wireless channel, remove the four screws securing the back cover of the device, then remove the back cover.
Leave the ribbon cable and power wires connected, the dip switches can be accessed without disconnecting them. Figure 5. Set the dip switches in sequence for the desired channel using the table below. Figure 6.
Re-install the board, install the batteries, then install the back cover. Make sure the data port plug is in place while assembling the case halves. Figure 7. Check the remote for proper operation. BATTERY REPLACEMENT The port on the bottom is not a charging port, it is a data connection for future devices. Do not connect any charging adaptors to this port. To replace the batteries, remove the two screws securing the battery cover then gently pry off the cover. Figure 8.
FIRST DESIGN (146-57-1) CHANNEL SELECTION To connect the wireless remote with the XF Pod or receiver board hold the “K1” + “Zoom” + “Menu” buttons on the remote for 5 seconds. This will cycle the remote until an available channel is found. This can take up to 10 seconds. If successful, the remote will now operate with the WinAlign program. If multiple WinAlign consoles are running, it may take several retries to find the correct channel.
COMPLIANCE STATEMENTS FCC ID: LS3-146591 IC: 2938A-146591 Model 146-59-1 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
TCF #: 2015071TCF Declaration of Conformity We, the undersigned, Company Address, City Country Phone number Fax number Hunter Engineering Company 11250 Hunter Drive USA 314 731 0000 314 716 1260 certify and declare under our sole responsibility that the following equipment: Product description / Intended use EU / EFTA member states intended for use Member states with restrictive use Manufacturer Brand Type (Model) RF Remote Control for use on Hunter Wheel Alignment Consoles EU: Austria, Belgium, Belarus
Česky [Czech] Dansk [Danish] Deutsch [German] Eesti [Estonian] English Español [Spanish] Ελληνική [Greek] Français [French] Italiano [Italian] Latviski [Latvian] Lietuvių [Lithuanian] Nederlands [Dutch] Malti [Maltese] Magyar [Hungarian] Polski [Polish] Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] Suomi [Finnish] Svenska [Swedish] Íslenska [Icelandic] Norsk [Norwegian] [Hunter Engineering Company] tímto prohlašuje, že tento [remote control] je ve shodě se základními požadavky a dalšími p
