PLATINUM ™ T E C HN OL OGY Wireless Wall Switch Guide for PowerRise®, PowerGlide® 2.
Control Like Never Before With Platinum™ Technology, you can operate individual and “group” window coverings without having to run wires to your windows. This guide shows you how to enjoy optimal performance using the wireless wall switch. The Platinum Technology Wireless Wall Switch RF GROUP 1 BUTTON UP/DOWN BUTTON RF GROUP 2 BUTTON RF GROUP 3 BUTTON RF GROUP 4 BUTTON ALL RF GROUPS BUTTON 2 hunterdouglas.
Getting Started Using the power of Platinum™ Technology is easy. In just two easy steps, your wireless wall switch is ready for setup. PROGRAM BUTTON RESET BUTTON BATTERY COMPARTMENT 1 POWER UP Remove the back cover from the wireless wall switch. Insert two AAA alkaline batteries as diagrammed inside the battery compartment. 2 RESET BUTTON Use a paper clip to press and quickly release the RESET button located next to the batteries. The ALL button will blink GREEN twice. Replace the back cover.
Installation Installing the wireless wall switch as a surface mount. SURFACE MOUNT 1. Remove back cover from the switch. 2. Use the mounting screws supplied with the switch to secure the back cover to the wall. 3. Place the switch assembly over the back cover, top first. 4. Press the bottom edge of the switch assembly over the bottom of the back cover until the bottom locking tab is secure. 5. Install faceplate over switch assembly. Note: The Platinum wireless wall switch may also be flush-mounted.
Programming RF Groups BEFORE YOU BEGIN Partially lower, traverse or tilt the window covering to ensure functionality. 1 PROGRAM MODE Remove the back cover of the wireless wall switch. Use a paper clip to press and quickly release the PROGRAM button on the back of the switch. The ALL button on the front of the switch will BLINK GREEN (for approximately 30 seconds). 2 GROUP NUMBER While the ALL button is BLINKING GREEN, press the GROUP number (1–4) to which you are adding the window covering.
Operating RF Groups PowerRise® and PowerTilt™ Operating Systems TO OPEN/CLOSE A WINDOW COVERING Press the GROUP number for the window covering(s) you wish to operate. The GROUP button turns SOLID GREEN. t To CLOSE press the DOWN button. t To OPEN press the UP button. TO STOP A WINDOW COVERING IN MOTION Press the GROUP number for the window covering(s) you wish to operate. The GROUP button turns SOLID GREEN. t For window coverings that are CLOSING press the UP button.
Operating RF Groups PowerGlide® 2.0 Operating System TRAVERSE THE WINDOW COVERING TO THE OPEN POSITION 1. Press the GROUP number for the window covering(s) you wish to operate. (GROUP button turns SOLID GREEN) 2. Press the UP button. TRAVERSE THE WINDOW COVERING TO THE CLOSED POSITION 1. Press the GROUP number for the window covering(s) you wish to operate. (GROUP button turns SOLID GREEN) 2. Press the DOWN button. TILTING THE VANES (Only available for Luminette® Privacy Sheers) 1.
Removing Window Coverings from a RF Group BEFORE YOU BEGIN Partially lower, traverse or tilt the window covering to ensure functionality. 1 PROGRAM MODE Remove the back cover of the wireless wall switch. Use a paper clip to press and quickly release the PROGRAM button on the back of the switch. The ALL button on the front of the switch will BLINK GREEN (for approximately 30 seconds).
Cloning 18" OR LESS TARGET WIRELESS WALL SWITCH SOURCE REMOTE (PROGRAMMED) 18" OR LESS SOURCE WIRELESS WALL SWITCH (PROGRAMMED) TARGET WIRELESS WALL SWITCH 1. Collect both the Source Remote or Wireless Wall Switch (already programmed), and the Target Wireless Wall Switch (new switch accepting program). 2. Remove the back cover from the Target Switch. 3. Use a paperclip to press and hold the RESET button on the Target Switch for approximatley 10 seconds. The ALL button will blink GREEN. 4.
Notes on Programming AVOIDING INADVERTANT PROGRAMMING TIP 1 Place wireless wall switch as close as possible to the IR receiver eye. TIP 2 Program window covering(s) prior to installation. TIP 3 Remove power from window covering(s) not being programmed. ENTERING PROGRAM MODE To activate Program Mode, use a paper clip to quickly press and release the PROGRAM button located on the back of the wireless wall switch.
Product and Operating Systems Overview PowerRise® Applause® honeycomb shades Brilliance® pleated shades Duette® honeycomb shades Nantucket™ window shadings Silhouette® window shadings Vignette® Modern Roman Shades PowerTilt™ Country Woods® wood blinds EverWood® Collection alternative wood blinds Modern Precious Metals® aluminum blinds PowerGlide® 2.
INFORMATION TO USER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules.