User's Manual

Test Signal to Repeater
Press and hold the P button on the back of the PowerView
®
Hub to
pair the Repeater to the shade network via the PowerView
®
App or
remote if you have not already done so. The light on the Repeater
fl ashes BLUE three times. If it does not, you may need to move the
Repeater to another location or add an additional Repeater.
Resetting the Repeater
To reset the Repeater and activate
learning mode, press and hold
the Repeater’s button until the
LED blinks AMBER, indicating the
Repeater has power but has not
been paired to a shade network.
Troubleshooting
My Repeater does not fl ash after
sending a test signal from the
PowerView
®
Hub.
• Verify there is power to the outlet
in which the Repeater is plugged.
• Add the Repeater to the shade
network via instructions in this
guide.
• Open the PowerView
®
App and select “Device Discovery.”
• Follow the on-screen instructions to set up each Repeater.
The Repeater LED turns solid BLUE to indicate the Repeater
has been paired to the network. Follow in-app instructions to
assign a custom Repeater LED color, if desired.
2. Pair Repeater to
PowerView
®
Shade
Network (if using
PowerView
®
App)
© 2017 Hunter Douglas. All rights reserved. All trademarks
used herein are the property of HunterDouglas or their
respective owners. 5110540077 3/17
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifi cations not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
Industry Canada
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
Class B Digital Device Notice
This Class B digital apparatus complies with Canadian ICES-003,
RSS-Gen and RSS-210.
CAN ICES-3 (B)/NMB-3(B)
European Conformity
We, the undersigned,
Hunter Douglas Window Fashions
One Duette Way, Broomfi eld, CO 80020, USA
Hunter Douglas Europe B.V.
Piekstraat 2, 3071 EL Rotterdam, The Netherlands
certify and declare under our sole responsibility that the
PowerView
®
Repeater conforms with the essential requirements
of the EMC directive 2004/108/EC and R&TTE directive 1999/5/EC.
A copy of the original declaration of conformity may be found at
www.hunterdouglas.com/RFcertifi cations.
PowerView
®
Repeater
QUICK START GUIDE
• Press and hold  “Stop” on the remote that was used
to create the PowerView
®
Shade Network until the
lights on the remote fl ash (approx. 6 seconds).
• With the remote no more than 3 feet from the
Repeater, press and release  “Stop.”
• The Repeater blinks BLUE three times to signal it has
been joined to the network. After the blinking stops, the
Repeater is still active.
3. Pair Repeater to
PowerView
®
Shade
Network (if using a
PowerView
®
Remote)
• Be sure the wall outlet has power.
• No more than six Repeaters should be used in a home,
unless otherwise instructed by a Hunter Douglas
Motorization Support Specialist.
• Do not place Repeater in direct sunlight.
1. Plug Repeater
into wall outlet
The LED blinks AMBER,
indicating the Repeater has
power, but has not yet been
joined to a PowerView
®
Shade Network.
Apple is a trademark of Apple Inc., registered in the
U.S. and other countries. HomeKit is a trademark of
Apple Inc.
Amazon and Alexa and all related logos are trademarks
of Amazon.com, Inc. or its affiliates.
MOTO_030117_PV RepeaterGuide_2x3_EngFrench_REV.indd 1-8 4/4/17 8:24 AM