User's Manual

PowerView
™
Repeater
QUICK START GUIDE
© 2015 Hunter Douglas. All rights reserved. All trademarks used
herein are the property of Hunter Douglas. 5110540077 5/15
POWER
SUPPLY
REPEATER
Plug repeater into power supply.
Each kit includes one PowerView
™
Repeater and one power supply.
Be sure the USB connector is firmly seated.
Plug power supply into wall outlet.
One Repeater per room with PowerView
™
window coverings is
recommended. Be sure the PowerView Repeater is pointing up and
the wall outlet has power. The green LED will come on to indicate
the Repeater has power and is operating, but not yet on a network.
Join PowerView
™
Network.
1. Press and hold Stop button on the remote until the lights
on the remote flash (approx. 4 sec.). 2. Press and release Stop
on the remote. 3. The Repeater will flash green once to signal it
has now been joined to the PowerView
™
Network.
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
Industry Canada
Under Industry Canada regulations, this radio transmitter may
only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
Class B Digital Device Notice
This Class B digital apparatus complies with Canadian ICES-003,
RSS-Gen and RSS-210.
CAN ICES-3 (B)/NMB-3(B)
Troubleshooting
My Repeater does not flash
when I send a Test Repeater
signal to it.
• Make sure the Repeater is
completely seated in the
USB port on the power
supply. Check that the
outlet that the USB power
supply is plugged into
has power.
• Test the Repeater with a
different USB power supply.
• Add the Repeater to the
PowerView
™
Network.
Refer to instructions in
this guide.
Test signal to repeater.
Press and hold the button on the back of the PowerView
™
Hub.
The light on the PowerView Repeater should turn GREEN. If it
does not, you may need an additional Repeater.
P
European Conformity
We, the undersigned,
Hunter Douglas Window Fashions
One Duette Way, Broomfield, CO 80020, USA
Hunter Douglas Europe B.V.
Piekstraat 2, 3071 EL Rotterdam, The Netherlands
certify and declare under our sole responsibility that the
PowerView
™
Repeater conforms with the essential requirements
of the EMC directive 2004/108/EC and R&TTE directive
1999/5/EC.
A copy of the original declaration of conformity may be found at
www.hunterdouglas.com/RFcertifications.
MOTORIZATION