Quick Start Guide

ManualsBrandsHunter Douglas Window Fashions ManualsElectronicsPlatinum APP Bridge

Platinum

™

App Bridge Kit

Trousse de pont pour

App Platinum

Quick Start Guide

Guide de

démarrage rapide

You’re ready to use the Platinum App.

Vous êtes prêt à utiliser l’App Platinum.

A. Platinum App Bridge

B. Platinum Repeater

A. Pont pour App Platinum

B. Répéteur Platinum

appartiennent à Hunter Douglas.

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

5110540056 9/12

Industry Canada

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for

the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the

equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Industrie Canada

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal

(ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres

utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité

nécessaire à l’établissement d’une communication satisfaisante.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Press the button on the back of the Platinum

™

App Bridge. The light on

each Platinum Repeater should turn

GREEN.

Other controls on the back of the bridge include the

RESET button,

which reboots the bridge; and the X button, which erases all your data from

the bridge when pressed for 6 seconds.

Appuyez sur le bouton à l’arrière du pont pour App Platinum

. Le témoin

sur chaque répéteur Platinum doit devenir

VERT.

Les autres commandes à l’arrière du pont comprennent le bouton de remise

à l’état initial

(

RESET

)

qui réinitialise le pont; le bouton X qui supprime toutes

les données du pont lorsque vous l’enfoncez pendant 6 secondes.

Test signal to repeater(s).

Vériﬁer l’émission d’un signal vers les répéteurs.

Summary of content (2 pages)

PAGE 1
5 Test signal to repeater(s). You’re ready to use the Platinum App. U.S. Radio Frequency FCC Compliance Vérifier l’émission d’un signal vers les répéteurs. Vous êtes prêt à utiliser l’App Platinum. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
PAGE 2
E 1 Vérifier le contenu de la trousse. A B CA E A C 2 Check kit contents. DB B E E C D A B E C C Connect power to bridge. Connecter le pont à l’alimentation électrique. 3 Connect bridge to wireless router. Connecter le pont au routeur sans fil. 4 Distribute repeater(s) as needed. Répartir les répéteurs au besoin. D D D A. B. C. D. E. Platinum™ App Bridge DC Power Supply USB Power Supply Cable Ethernet Cable Platinum Repeater Kit 1 Platinum Repeater 1 DC Power Supply A. B. C.