User's Manual

产品介绍
配件清单
使用
充电
连接手机
开机
充电盒
指示灯
触摸按键
硅胶耳套
充电针
充电盒
硅胶耳套x3对 说明书 Micro USB充电线
耳机
耳机从盒子里取出后，耳机自动开机，耳机连接手机超时或超距超时关机，长按
耳机功能键2秒开机。
关机
放入充电盒（没有按键关机）,红色LED长亮，设备关闭。
耳 机 充 电 ：耳机放入充电盒，自动进入充电状态，耳机LED红灯长亮，表示充电
中，耳机充满后LED绿灯亮1S熄灭。
从盒子取出耳机，当听到“咚....”，会听到主耳机提示：“Primary”，从耳机提示 :
“Secondary”提示完成后，用手机连接蓝牙，耳机LED灯红绿交替快闪，配对时
间5分钟，5分钟后未连接到设备进入到关机。
将耳机从盒子中取出，当听到“咚....”开机提示音后，主耳机提示“Primary，从耳
机提示“Secondary"左右耳机LED灯红绿交替快闪，耳机等待连接。开启设备蓝
牙，搜索并连接蓝牙设备“LC001”。
有配对记录后，耳机从充电盒中取出，耳机将自动重新连接最近连接过的一台
手机。
从耳在桌面上，主耳与手机离开到超距距离，主耳继续使用，从耳进入到回连
主耳TWS模式，从耳LED灯红绿交替快闪，如果5分钟内没有连接到主耳，从耳进
入自动关机；
双耳同时离开手机到超距距离，耳机进入回连蓝牙状态，LED灯红绿交替快闪，
5分钟内如果没有回连到手机，耳机进入自动关机(有提示音)。
双击耳机触摸键（L 耳机单机使用时）；
蓝牙连接状态，非电话模式。
①耳机低电量时，红色LED灯1秒闪两次，间隔10秒；
②当耳机入盒不能关机，说明充电盒没电，请及时充电。
默认出厂L为主R为从，首先从充电盒拿出操作的为主、后为从。
首先让双耳进入配对状态，然后三击，最后一击大于2秒，然后耳机关机。
首次使用进入配对模式
自动重新连接
超距连接
通话状态/音乐播放
主从定义
清除连接记录
如果在回连1次历史记录蓝牙后没有回连到设备，就进入到蓝牙搜索配对状
态，耳机LED灯红绿交替快闪； 在这5分钟内还没有设备连接耳机， 耳机就进
入关机状态。手机需在蓝牙有效范围内，且蓝牙为开启状态。
连接成功
充电接口
耳机
真无线耳机使用说明书
充电盒充电：①当充电盒指示灯显示红灯时，表示充电盒电量较低，此时请给充
电盒充电。
②当充电盒指示灯显示绿灯长亮时，表示充电盒已充满电，此时请
停止充电。
主从耳超距：
Master-slave earphone distance
双耳超距：
查看电量：
启动手机系统语音助手：
双击
双击L耳
双击L耳
长触2秒
播放/暂停
音量+/音量-
接听电话
挂断电话
拒接电话
双触摸右边耳机键（TWS连接模式下）
双触摸耳机触摸键（R 耳机单机使用时）
手机操作
左边 右边
双触摸左耳耳机触摸键（TWS连接模式下）
双触摸耳机触摸键（L 耳机单机使用时）
Double
Click
Double
Click "L/R"
Double
Click "L"
Long press
button 2s
Play/Pause
Volume+/-
Answer The Phone
Hang Up
Reject a Call
Touch the touch key（use R alone）
Mobile Operation
Left Right
Double touch left touch button
(TWS connection mode)
double touch the touch key（use L
alone）
双击触摸按键
产品中有害物质的名称及含量
本表格依据 SJ/T 11364 的规定编制。
O：表示该有害物质在该部件所有均质材料中的含量均在
GB/T 26572 规定的限量要求以下。
X：表示该有害物质至少在该部件的某一均质材料中的含
量超出 GB/T 26572 规定的限量要求，且目前业界没有成熟的
替代方案。
警告：
!
禁止拆解、撞击、挤压或投入火中；
若出现严重鼓胀,请勿继续使用；
请勿置于高温环境中；
电池浸水后禁止使用。
产品型号
用户信息
销售单
位信息
SN 号码
购机日期姓名
电话
地址
发票号码
名称
地址
电话
（加盖公章）
产品保修卡
材质：105g双铜纸，冷灰11c单色印刷 表面过哑油 风琴9折
折叠尺寸：75*55mm
Product Overview
Accessories
Instructions
Charge
Connect Mobile Phone
Power On
Charging Box
Indicator
Light
Touch Button
Silicone Earcaps
Charging Needle
Charging Box
Silicone Earcaps x 3pair User manual Micro USB
charging cable
Earphones
Power on automatically when Remove earphone out of box please long
press earphone function button for 2s to turn on, if connect timeout or
distance.
Power Off
Put it into the charging box (without button off), the red LED is long bright,
and the device is off.
Earphone Charging: put the earphone into the charging box and automatically
enter the charging state. The red LED is on , indicating charging. After full
charged, the green LED goes off for 1S Charging box charging:
①Red light on, indicates low power. Please charge the charging box in time.
②Green light long on ,indicates full charged. Please stop charging.
Remove the headset from the case, when hear prompt tone, double-click
on the left and right ear touch keys at the same time, will hear the primary
headset prompts: "primary", secondary headphone ": secondary". Then use
mobile phone to connect bluetooth, the headset LED lights flash red and
green alternately, pairing time lasts for 5 minutes. If not connected, the
device will shut down.
After first paired, the earphone will automatically reconnect to the most
recently connected one when removed from case.
If not connected to the historical device for 1 time, the device will enter
to search bluetooth pairing state, and the headphone LED light will flash
red and green alternately; The device without connected after five minutes
will enter into shutdown state.
Take the earphone out of the box. When hear "Dong", it means power on.
The primary earphone prompts: "primary", the secondary one prompts:
"secondary". Earphones LED lights flash red and green alternately, waiting
for connection. Turn on the device bluetooth, search and connect the device
"LC001".
Default factory Settings: the primary R, L is secondary. The primary one taken
out is manually reconnected outside the case, and the manual operation is
the primary.
First put both earphones into pairing state, then three strikes, the last strike
is more than 2s, finally power off.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes
or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radic communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Hereby, VOC declares that the radio equipment type True Wireless
Earphones is in compliance with Directive 2014/53/EU. The full text of
the EU declaration of conformity is available at the following internet
address: http://www.vocacoustic.com/
Secondary earphone on the table, take the primary earphone and mobile
phone to the distance, the primary earphone continues to use, the secondary
ear enters into reconnecting state mode. Secondary earphone LED lights flash
alternately red and green, if not connected to the primary earphone within 5
minutes, secondary earphone will close down.
Put earphones in the overrange distance from phone. The earphones will
enter into the reconnecting state, and the LED light will flash red and green
alternately. If not connected to phone within 5 minutes, earphones will
close down.
Double click the earphone touch button ( use L earphone alone),Bluetooth
connection, not phone mode.
①When power is low, red led light flashes twice every 10 seconds.
②Please charge the box in time, if earphone can’t be turned off in the case.
First pairing mode
Automatic Reconnection
Call Status Or Play Music
Master-Slave Definition Clear Connection Record FCC
CE
Distance Connection
Binaural Distance
Start The Phone System's Voice Assistant
Connection
Charging
Port
Earphones
True Wireless Earphones User Manual
Battery State
Double touch the right key（TWS
connection mode)
Double Click
Touch Button
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
耳机
充电盒
电池
充电线
耳套
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
中文正面
英文背面