000S wireless video transmission system supporting HDMI & SDI (VAXIS STORM1000S)
Introduction...................................................................................... 1 1.Cautions........................................................................................ 2 2.About ........................................................................................... 3 3.Installation .................................................................................. 10 4.Operation instruction.................................................................... 12 5.
Introduction Thank you for choosing our long-range wireless HDMI / SDI HD products. Before you install the product, please read the user manual carefully and follow the manual of the user manual to avoid product damaged or other safety accidents. Due to product version upgrade or other reasons, the contents of this manual will be updated from time to time.
1. Cautions ■Logo and meaning Careful, warning, dangerous, Pay attend to following items. ■Cautions Do not use this product in the extreme hot, cold, dusty or humid environments. Prevent friction with hard objects. Avoid the product falling down from a high place, or it may damage the hardware. The product is not water proofed. So do not get any liquid into the unit please. Do not dismantle, assemble or alter the product arbitrarily.
2. About ■Product Model and standard The VAXIS STORM1000S Wireless HDMI/SDI Transmission Suite utilize today’s most advanced wireless video transmission technology, which can realize the broadcast-class and uncompressed 3G SDI/HDMI HD video signal transmitted with no compression and zero delay. The suite includes one transmitter and one receiver, both of them provides a 3G/HD SDI interface and a HDMI interface. The transmitter with 2 sword antennas, and 5 antennas built-in receiver, and it can work in 5.
■Main features: HDMI 1.3 spec supports HDMI and 3G SDI input and output Highest resolution 1080p 60,no delay and no compression Support audio formats include Dolby True HD, DTS-master, etc. AES-128 encryption with air interface HD video data stream Support point to point, and point to multi points network topology 5GHz ISM frequency band，maximum 10 frequency channels selected by user knob, coexist with WIFI.
■ Parameters: Transmitter Receiver SDI Input（BNC Female）; SDI loop out SDI Output X 2（BNC Female）; HDMI （BNC Female）; HDMI Input(Type A Output(Type female); 2 Antenna port(2 SMA male）; port(SMA male）; DC input (2 pin LEMO DC input (2 pin LEMO female) female) Supply voltage range 6-36V DC 6-36V DC Power consumption <6.
■Name of the product parts Transmitter: ① Fan ② Screen Operation ③ 1/4-20 threaded hole DC Input, LEMO 2 Pin Bseries connector ④ ⑤ DC switch ⑥ HDMI Input ⑦ SD/HD/3G SDI out ⑧ SD/HD/3G SDI Input ⑨ USB interface to upgrade 6
⑩ DC Input, LEMO 2 Pin Bseries connector Receiver: ① Fan ② Screen Operation USB interface to upgrade ③ Screen control button SD/HD/3G SDI output 7
④ DC switch HDMI output ⑤ USB interface to upgrade ⑥ HDMI output ⑦ SD/HD/3G SDI output1 ⑧ SD/HD/3G SDI output2 Screen control button ⑨ V-LOCK or AB-LOCK optional plate 1/4-20 threaded hole ⑩ DC Input, LEMO 2 Pin B series connector Screen Operation: ①Temperature display ②Fan’s speed display ③Channel display ④Signal strength display 8
⑤Signal source display ⑥Signal input format display ⑦0`S function ⑧Battery voltage display ■Packing list: 1 piece transmitter 1 piece receiver 3 pieces 5GHz polydirectional and high performance sword antennas(SMA female) 2 pieces DC conversion cable (LEMO 2 pin male to D-Type) 1 piece 3G-SDI flexible cable 1 piece Vaxis Blue Noga Arm 1 user Manual SONY NP-F970 battery plate V-LOCK battery plate 9
3.Installation and Debugging ■Installation details and cautions Transmitter Settings a) Contact 2 pieces sword antennas to Transmitter’s SMA male antenna connectors b) There are 3 1/4-20 screw nuts in the bottom transmitter metal case, which are located on the bottom. So the user can utilize Vaxis Noga Arm to fix the transmitter on camera. c) If the product you purchased has a battery plate, you can connect the battery corresponding to the battery plate to the transmitter.
b) The user also can utilize a subsidiary LEMO 2 pin male to D-Type receptacle power cable to get power input from an outside power source。 Typical connection instruction Connect camera SDI or HDMI output to transmitter SDI or HDMI input port, and the transmitter can fixed in hot-shoe port of the camera. Connect HDMI or SDI output port of the receiver to SDI or HDMI input port of the HD monitor. Make sure all antennas, batteries and Video cable are equipped normally.
4. Operation instruction ■Getting started After finishing all steps above, system is workable, follow below steps. a) Ensure the video source output of the camera is OK, and the HD monitor is power on and switched to connected video input port. b) Ensure all input, output SDI or HDMI cables are connected. c) Ensure both the transmitter and receiver installed batteries or DC input ports connected to outside power sources.
“Video” will light. Before the receiver output the normal video signal, the monitor will display an OSD of “Link connecting……” like below picture: Link C onnecting... g) The system will spend about 10 seconds to complete the initialization and wireless connection. The actual connection time will be associated with the wireless environment of the specific usage scenario.
face, and don’t turn round any sides with too big angle. The real transmission distance is also relevant to current air electromagnetic environment, because the system works in ISM band, it is exposure to all kind od 5GHz band air interference, we suggest the users should do a manual frequency sweep by adjusting frequency selection knob with a circle before using the equipment, then choose the best frequency channel for stable performance.
■ Frequency Selection The wireless suite can work in 5.1-5.9GHz frequency band and be flexibly software configured to licensed or ISM band of global different regions. Meanwhile, on the side of both transmitter and receiver Set aside the manual communication channel selection knob, can use the random screwdriver to adjust the channel. Please note: Transmitter and Receiver should keep in the same channel(Similar to the intercom principle).
6.Trouble shooting ■Normal problems a) No output on display Please check the TX and RX power first, if TX or RX is powered from battery or external power, please ensure the battery or external power source can supply the power. Then check if TX antennas and RX antennas are installed right. After that, check the Transmitter’s OLED screen, if haven’t show the signal, then check SDI or HDMI cable is plugged in and video source is ready please.
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
