6189N-SFC Wi-Fi Single-band 1X1 802.
6189N-SFC Module Datasheet Office: 6 Floor, Building U6, Junxiang U8 Park, Hangcheng Avenue, Bao'an District, Shenzhen City, CHINA Factory: No.8, Litong Road, Liuyang Economic & Technical Development Zone, Changsha, Hunan, CHINA TEL: +86-755-2955-8186 Website: www.fn-link.
6189N-SFC Revision History Version Date Revision Content Draft Approved 1.0 2019/01/10 New version Lzm Lxy 1.1 2019/04/10 Update thickness dimension Lxy Szs 1.2 2019/08/06 Update packing information Lxy Szs 1.3 2019/11/12 Update module photo Lxy Szs 1.4 2020/12/22 Added HSmode timing info.
6189N-SFC CONTENTS 1 Overview....................................................................................................................................1 1.1 Introduction......................................................................................................................... 1 1.2 Features.............................................................................................................................. 1 1.3 General Specification..........................................
6189N-SFC 1 Overview 1.1 Introduction 6189N-SFC is a highly integrated and excellent performance Wireless LAN (WLAN) SDIO network interface device. High-speed wireless connection up to 150 Mbps. It can be easily manufactured on SMT process. This WLAN Module design is based on Realtek RTL8189FTV-VC-CG. It is a highly integrated single-chip Wireless LAN (WLAN) SDIO network interface controller complying with the 802.11n specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip.
189N-SFC 1.3 General Specification Model Name 6189N-SFC Product Description Support Wi-Fi functionalities Dimension L x W x T: 23 x 21 x 4.8 (typical) mm Wi-Fi Interface Support SDIO Operating temperature 0°C to 70°C Storage temperature -55°C to +125°C 1.4 Recommended Operating Rating Min. Typ. Max. Unit 0 25 70 VBAT 3.0 3.3 3.6 deg.C V VDDIO 1.7 1.8 or 3.3 3.6 V Operating Temperature ※1.5 EEPROM Information WI-FI Vendor ID 024C Product ID F179 2 General Specification 2.
6189N-SFC PHY Data rates Wi-Fi: 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: up to 150Mbps Transmit Output Power Wi-Fi: 802.11b@11Mbps 16±2dBm 802.11g@54Mbps 14±2dBm 802.11n@65Mbps 12±2dBm Other rate power control by power by rate. EVM 802.11b /11Mbps: EVM≦-9dB 802.11g /54Mbps: EVM≦-25dB 802.11n /65Mbps: EVM≦-28dB Receiver Sensitivity (HT20) 802.11b@8% PER 11Mbps< -82dBm 802.11g@10% PER 54Mbps< -71dBm 802.11n@10% PER MCS 7 <-67dBm Operating Channel Wi-Fi 2.
6189N-SFC GND 1 19 GND GND 2 18 GND GND 3 17 GND SD_D3 13 14 15 16 GND SD_D2 12 SD_D1 11 SD_D0 10 SD_CLK 9 SD_CMD 8 WL_WAKE_HOST NC 7 CHIP_EN VBAT 6 GND 5 VDDIO 4 3.2 Pin Definition NO. Name Type 1 GND Ground connections 2 GND Ground connections 3 GND Ground connections 4 VBAT 5 NC 6 VDDIO 7 GND 8 CHIP_EN I Wi-Fi enable pin, default pull high 3.3V 9 WL_WAKE_HOST I/O WLAN to wake-up HOST 1.8V ~ 3.3V 10 SD_D2 I/O SDIO Data line 2 1.8V ~ 3.
6189N-SFC 14 SD_D0 I/O SDIO Data line 0 1.8V ~ 3.3V 15 SD_D1 I/O SDIO Data line 1 1.8V ~ 3.3V 16 GND Ground connections 17 GND Ground connections 18 GND Ground connections 19 GND Ground connections P:POWER I:INPUT O:OUTPUT 4 Dimensions 4.1 Module Picture L x W : 23 x 21 (+0.3/-0.1) mm H: 4.8 (±0.2) mm Weight 1.65g 4.
6189N-SFC 4.3 Module Physical Dimensions 23 2.65 1 4.15 5.65 11.5 0.7 0.35 1.15 2.65 4.15 5.65 7.15 8.65 10.
6189N-SFC 4.4 Layout Reference (unit: mm ) 23 2.65 1 4.15 5.65 11.75 0.7 4.15 5.65 7.15 8.65 10.75 FN-LINK TECHNOLOGY LIMITED 7 0.35 1.15 2.
6189N-SFC 6 Host Interface Timing Diagram 6.1 SDIO Pin Description The module supports SDIO version 2.0 for all 1.8V 4-bit UHSI speeds: SDR12(25 Mbps), and SDR25(50Mbps) in addition to the 3.3V default speed(25MHz) and high speed (50 MHz). It has the ability to stop the SDIO clock and map the interrupt signal into a GPIO pin. This ‘out-of-band’ interrupt signal notifies the host when the WLAN device wants to turn on the SDIO interface.
6.
6189N-SFC Parameter Symbol Minimum Typical Maximum Unit SDIO CLK(all values are referred to minimum VIH and maximum VILb) Frequency - Data Transfer mode fPP 0 - 50 MHz Frequency - Identification mode fOD 0 - 400 kHz Clock low time tWL 7 - - ns Clock high time tWH 7 - - ns Clock rise time tTLH - - 3 ns Clock low time tTHL - - 3 ns Input setup time tISU 6 - - ns Input hold time tIH 2 - - ns Output delay time - Data Transfer mode tODLY - - 14 ns Outp
6189N-SFC 6.3 SDIO Power-on sequence Symbol Min Typical Max Unit T33ramp 0.2 - No Limit ms Toff 250 500 1000 ms T33ramp 0.2 0.5 2.5 ms T12ramp 0.1 0.5 1.
6189N-SFC 7 Reference Design Note: 1. chip_EN could not use for module power off, please switch the 3.3V power for module on/off. 2.please keep the antenna on no metal area. 3.
6189N-SFC 8 Ordering Information Part No. Description FG6189NSFC-00 RTL8189FTV-VC-CG b/g/n, Wi-Fi, 1T1R, 23X21mm, SDIO, PCB V3.0 with antenna 9 The Key Material List Shielding cover 6189N-SFC V1.0 Shielding cover,height=1.4 mm 信太，精力通 Crystal 26mhz 3225 ±10ppm, 10.5pF HOSONIC，ECEC ESD 0402 5.5V 0.1pF Sunlord,Murata Chipset RTL8189FTV-VC-CG Realtek PCB 6189N-SFC V3.0 black，23x21-0.8mm XY-pcb ， Sunlord ， KX-pcb 10 Environmental Requirements 10.
6189N-SFC 10.2 Patch Wi-Fi modules installed before the notice Wi-Fi module installed note: 1. Please press 1 : 1 and then expand outward proportion to 0.7 mm, 0.12 mm thickness When open a stencil. 2. Take and use the WIFI module, please insure the electrostatic protective measures. 3. Reflow soldering temperature should be according to the customer the main size of the products, such as the temperature set at 250 + 5 ℃ for the MID motherboard.
6189N-SFC 11 Package 11.1 Reel A roll of 350pcs 11.2 Packaging Detail the take-up package Using self-adhesive tape Size of black tape:44mm*12.48m the cover tape :37.5mm*12.
6189N-SFC NY bag size:420mm*450mm size ：335*335*55mm The packing case size:335*255*360mm FN-LINK TECHNOLOGY LIMITED 16 Proprietary & Confidential Information
FCC Statement FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Integral antenna with antenna gain 2dBi This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC STATEMENT This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference.
