SD Digital Receiver User’s Manual IR2000SD The default parental control code is 1234. The default installation code is 0000.
Thank you for purchasing a HUMAX product. Please read this user’s manual carefully to be able to safely install, use and maintain the product at maximum performance. Keep this user’s manual next to your product for future reference. The information in this user’s manual is subject to change without notice.
Warnings, Cautions and Notes Throughout the whole manual, pay special attention to the following marks that indicate hazardous situations. • Warning Indicates a hazardous situation which could result in serious injury. • Caution Indicates a situation which could damage the equipment or other apparatus. • Note Indicates additional information to make the user aware of possible problems and information of any importance to help understand, use, and maintain the installation.
This product has been manufactured to comply with international safety standards. Please read the following safety precautions carefully. Safety Instructions and Precautions 1. MAINS SUPPLY 90-250V a.c., 50/60Hz • Operate this product only from the type of power supply indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your local power company.
10.LOCATION • Place the product indoors to avoid exposing it to lightning, rain or sun. • Do not place it near a radiator or heat register. • Do not place naked flames such as lighted candles on or near the product. • Make sure it has more than 10 cm clearance from any appliances susceptible to electromagnetic influences, such as a TV or a VCR. • Do not block the openings with any object, and do not place the product on a bed, sofa, rug, or other similar surface.
Warning ** The mains plug, as a disconnection device, shall remain readily accessible by the user. ** 1. To avoid damage of the power cord or plug; • Do not modify or process the power cord or plug arbitrarily. • Do not bend or twist the power cord. • Make sure to disconnect the power cord holding the plug. • Keep heating appliances as far as possible from the power cord in order to prevent the cover vinyl from melting.
1. Before Using the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Conditional Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.
! ! This chapter provides detailed instructions on the product and its accessories. " Please check all package contents before using your product. ** Note: • Faults may occur if the remote control is left without battery for a long time. Always keep the battery inserted in the remote control. • Package contents may vary according to area.
! $ % Open the right-hand flap on the front panel of the product to expose the card slot. ** 1. STANDBY BUTTON Switches between operation and standby modes. 2. IR SENSOR Receivers the signal from the remote control. 3. MENU BUTTON Displays the main menu. 4. OK BUTTON Selects a menu or confirms the selected operation. Displays the channel list while watching a programme. 5. ARROW BUTTONS Changes the channel or moves the cursor up, down, left or right. 6.
! % ' Although some TV and radio services are free to air, others are available on a subscription basis and can only be enjoyed via a Conditional Access component. ( ) The Smartcard looks similar to a credit card and is inserted into the slot behind the right-hand front flap of the product. A valid Smartcard entitles you to view and listen to all the channels you choose to subscribe to. 1.
! + % ** 1. LNB IN Connect a satellite antenna cable. 2. AUDIO Use an RCA cable to connect to the TV. 3. VIDEO Use an RCA cable to connect to the TV. 4. USB Port Service Port ** Note: The image shown may differ from the actual product.
! + ) % STANDBY Switches between operation and standby modes. MUTE Mutes audio. WELCOME Displays the service information. MAIL Displays the mail message. TV/RADIO Switches between TV and radio modes. WIDE Sets the display format. NUMERIC 0-9 MENU Displays the main menu. EPG Displays the programme guide. COLOUR Colour keys for interactive applications. EXIT Exits all On-Screen Display (OSD) screen. SLEEP Sets the sleep time.
! ** ARROW Moves the cursor up, down, left and right. OK Selects a menu or confirms a selection. Displays the channel list while you are watching a programme. BACK Returns to the previous channel. FAV Displays the favourite list. +/Adjust the audio volume. i Displays the channel and programme information. OPT+ Displays the channel’s attributes. P Change the channel or page. AUDIO Displays the audio list. SUBTITLE Displays the subtitle language list.
! !- This chapter describes how to connect your product to the TV with the particular equipments for gaining optimum signal quality. Note: If you encounter any problems setting up your product, please contact your local product distributor. ' Connect the antenna to the LNB IN. ./ Connect the product and the TV using an RCA cable.
! 0 1 1. Connect the power cord of the product to a wall outlet. 2. Power on by pressing the STANDBY button of the remote control or the STANDBY button at the front of the product. ** Inserting Batteries 1. Press the hook upward and lift the battery cover off . 2. Insert the batteries matching the plus(+) and minus(-) at each end. 3. Close the cover.
( %% 2 ( %% 2 When powering on your product for the first time after purchase, the installation wizard will operate automatically. Tip: The default installation code is 0000. If you have forgotten your installation code, please contact your local product distributor. 3 ! Select your language. + Select your country. '! ) Channel search will activate.
( %% 2 + !% The result of the installation wizard is shown. Select Finish to exit the wizard.
4 ! 15 5 0 4 ! 15 5 0 Press the MENU button to display the menu. % ) Select Welcome to contact the broadcasting operator. % 3 Select Channel List to display the channel list. ./ ! Select TV Guide to display the electronic programme guide. 4 % 4 Select Mail Messages to check the mails from the broadcasting operator. When a new mail arrives, the mail icon will appear on the screen. Press the OK button to see the details.
1- 1- This chapter describes the basic functions the product provides such as switching channel, volume control and other common features. 0 % You can switch the current channel by pressing the P number directly using the NUMERIC(0-9) buttons. button or entering the channel / %!) % Press the VOL +/- button to adjust the audio volume. Press the MUTE button to stop the audio temporarily. You can set the display format.
1- . % 7 Press the TEXT button. To display the teletext menu, press the MENU button in teletext mode. Select the teletext function you want and press the OK button. # + $ Press the LIST button to display the RSS(Really Simple Syndication) feed for Almajd. Select the category you want and press the OK button. A banner of the selected category is displayed and changes every 10 seconds.
% 3 % 3 The channel list will help you find the channel you want to watch quickly and easily. You can access the channel list in several ways. Press the OK button while you are watching a programme. Press the MENU button and select Channel List. ** % Select the channel you want to watch and press the OK button. Press the button and select a channel group. Press the RED button to sort the list in numerical or alphabetical order.
# ./ ! # ./ ! The TV guide is an on-screen guide of grid type which displays the programme information of channels in time and date order. You can access the TV guide in several ways. Press the EPG button. Press the MENU button and select TV Guide. # . 6% ! You can view the programme information of all channels in time and date order. Note: Press the BLUE button to list the channel of other groups. # $ Find will help you find the programmes more specifically using the keyword or genre.
& & & In this chapter you can set options for language, parental control, time, video and screen display. 3 ! System Language, Audio Language, Subtitle Language % % Maturity Rating, Change Parental Control Code Note: The default parental control code is 1234. If you have forgotten your parental control code, please contact your local distributor. .
& & ; % In this chapter you can edit all channels in the channel list or make changes to the favourite lists of the channels you have chosen. You will be prompted to enter the installation code to access this menu. Note: The default installation code is 0000. If you have forgotten your installation code, please contact your local product distributor. ; % 3 You can delete, lock or rename multiple channels. Note: You cannot move the channels.
& & ( %% Installation menu allows you to configure your antenna and search the available TV and radio channels. Software update and default setting are also available in this section. MENU -> Settings -> Installation You will be prompted to enter the password to access this menu. Note: The default installation code is 0000. If you have forgotten your installation code, please contact your local product distributor. '! You can search satellites and channels automatically.
& 4 ! % You can search the channels as the satellite you set. ** 1. Enter the options. Frequency: Enter the frequency of the transponder. Polarisation: Select the polarization of the transponder. Symbol Rate: Enter the symbol rate of the transponder. Transmission: Select DVB-S2 or DVB. Modulation: Select QPSK or 8PSK when selecting DVB-S2 in Transmission. FEC: Select the FEC of the transponder. 2. Select OK and press the OK button.
& & ) ) ( ) The system information is displayed. % ! You can check the signal strength and quality of the searched channels. (+<;.1 0 - When the Over-The-Air is available, IRDETO Software Update is activated. % ' You can view the Smartcard information.
* '-- 7 * '-- 7 * - Tuner & Channel Input Connector F-Type, IEC 169-24 Frequency Range 950MHz to 2150MHz Signal Level -25dBm to -75dBm LNB Power & Polarisation Vertical : 12.4 ~ 13.7V Horizontal : 17.1 ~ 18.7V Current : MAX. 350mA (overload protection) 22Khz Tone Frequency : 22KHz ± 2kHz Amplitude : 650mVp-p +/-250mV DiSEqC 1.0, 1.
* '-- 7 Memory Flash Memory 8 MB RAM 64 MB EEPROM 8 KB Audio/Video In/Out Video CVBS Audio Audio L/R Power Supply Input Voltage AC 90-240 volts, 50/ 60Hz Type SMPS Power Consumption 16W Protection Separate Internal Fuse & Lightning protection Physical Specification Size 260mm x 182mm x 50 mm Weight (Net) 1.
