Assembly Instructions
Where to apply the touch switch
Application site : This intelligent switch is
desi
g
ned for home
,
hotel hotel
,
office
Chapter1. Switch Assembly and
Connection Method
This touch switch is designed to be concealed
Chapter2. Product Requirements
Parameters
Pd R i P
Chapter4.Other matters
1. Switch BacklIght Indicator
Remote control remote control switch backlight indicator
Chapter3.
433 MHz remote control
setup and release method
Chapter4.OFCC Statement
ThisdevicecomplieswithPart15oftheFCCrules.Operationissubjecttothe
followingtwoconditions:1)thisdevicemaynotcauseharmfulinterference,and
2)
Touch Switch
Manual
g,,
building and commercial premises control
lighting. Suitable Load : LED lamp,
incandescent lamp, energy-resIstant lamp,
electronic transformer or inductive voltage,
electronic ballast lamp, electronic type
converter .The electric lamp that drives a
fluorescent lamp, an electronic ballast, a
high-voltage gas discharge lamp (HID) fan, is
more stable and reliable for intelligent
switches. Please use various kinds of tools
dlihi dlihi C hih
This
touch
switch
is
designed
to
be
concealed
in a concealed or concealed manner.Wiring
installation
1. Remove the panel with screwdriver Tear down
the front panel as figure below
2. Connect the wire.Connect live wire to L
terminal. Connect neutral wire of light to
light terminal(L2, L3, etc).
P
ro
d
uct
R
equ
i
rements
P
arameters
Rated working voltage : 110 V - 240 V AC
Load power : 3 - 300 W / Road, total power output 900 W
Please don't overload your load.
If you use LED lamp or save lamp, maximum resistance load
is 100 W / Road
Max. Current : 5A
Work temperature : 20℃ to 70 ℃
Work frequency : 50 / 60 Hz.
Power consumption : 0.02 W
Relative humidity : 10 % to 93 % (non-cooled condensation)
Self Power Consuming:Less than 0.1mA
Transportation time : 100,000 times
Power Supply:Single Live Line.If a small power LED lamp
Unable to find the switch when the lights light up at
night, Non-state Blue Directive
When installation is installed, there is an electrical
shock before installation.
Touch the remote control switch on the surface of the
switch during working hours to ensure the optimal working
function.
Use standard low box, do not use low metal box, because
it is possible to avoid remote or electric shock hazards
because it may cause electrical shocks or cause electric
shocks.
3. Manufacturer's guarantee
If the user is in normal use, the manufacturer will
id lit f lif i b d th 1
Connect: If the switch button is
pressed for 5 seconds, the registration
mode is converted. If the remote
control button is pressed, the
connection is completed after "D" is
sounded.Release: If the switch button
is pressed for 10 seconds, it will
sound "D" twice before disconnecting.
2)
thisdevicemustacceptanyinterferencereceived,includinginterferencethat
may
causeundesiredoperation.
Note:Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfora
Class
Bdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsare
designed
to
providereasonableprotectionagainstharmfulinterferenceina
esidential
installation.
Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyand,ifnot
installedandusedinaccordancewiththeinstructions,may
cause
harmful
interferencetoradiocommunications.However,thereisnoguaranteethat
interferencewillnotoccurinparticularinstallation.Ifthisequipmentdoescause
harmfulinterferencetorad
ioortelevisionreception,whichcanbedeterminedby
turningtheequipmentoffandon,theuserisencouraged totrytocorrectthe
interferencebyoneormoreofthefollowingmeasures:
‐‐Reorientorrelocatethereceivingantenna.
Manual
an
d
li
g
h
t
i
ng an
d
li
g
h
t
i
ng o
f
EMC
, w
hi
c
h
are
carefully monitored by EMC. Products inactive :
This intelligent switch does not live in a
factory, hospital CT / NMR, etc., with strong
radiation and strong electromagnetic waves in
the field. "
Catalogue :
Chapter1. Switch Assembly and Connection
Method
3.Install switch on the wall.Place the switch
on the wall Screw the both sides; Install the
front panel.Installation completes.
Power
Supply:Single
Live
Line.If
a
small
power
LED
lamp
(5 W) or other light source is compatible with switches
or controls,The phenomenon of automatic shutdown or
closing of the switch is automatically closed after the
switch is opened. The converter parts supplied by the
manufacturer must be mounted on the rear side of the
switch (providing free investigations)
prov
id
e qua
lit
y assurance
f
or
lif
e repa
i
rs
b
eyon
d
th
e
1
-
year warranty (except the panel) and 1-year warranty.
The situation below is not warranted
1）In case of artificial damage or external damage such
as water ingress.
2）User disassembles or alters the body of the product
(not including panel disassembly)
3）Beyond the technical parameters of this product
4）Earthquake-In-place
‐‐Increasetheseparationbetweentheequipmentandreceiver.
‐‐Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich
the
receiverisconnected.
‐‐Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Changesormodificationsnotexpresslyapprovedbythepartyresponsiblefor
compliancecouldvoidtheus
er’sauthoritytooperatetheequipment.
FCCRadiationExposureStatement
ThisdevicecomplieswithFCCRFradiationexposurelimitssetforthforan
uncontrolledenvironment.Thistransmittermus tnotbeco‐locatedoroperating
in
conjunctionwithanyotherantennaortransmitter.