TPMS USER MANUAL
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This device complies with part 15 of the FCC Rules.
TPMAI1DIC1 USER MANUAL Thank you for choosing products.
Contents Precautions 1 Product description 2 Installation Transmitter installation steps 3 Receiver installation steps 4 Operation System introduction 5 System settings 6 Backlight settings 7 Common alerting mode 14 Troubleshooting 16 Disclaimer 17 Equipment connection 18 Contents
Precautions Before using this product, please be sure to have read the 1 This product is applicable to 12V cathode 24V grounding battery system car, please do not install the product in 24V truck or bus. 2 12V Do not install the product in the field of impacting driver's vision or driving operation. 3 In order to avoid traffic accidents caused by decentralizing driver's attention, please do not operate the product while driving.
Product Description Composing component Tire Pressure Monitoring System includes the following components: Name SN. Icon Amount 1 Receiver 1 2 Transimitter 4 3 Paste board 1 Product technical specifications Transimitter Operating temperature -40℃ ~ 105℃ Operating humidity ≤95%RH Product Size 73×67×20mm Product life Normal use>6 years Pressure measuring range 0kPa~800kPa Transimitter frequency 433 .
Installation Transmitter installation steps: 1 remove tires from the car, remove the rubber tire after the tires were deflated 2 clean the rim 3 Screw the protective cap, jacket nut, flat washer from the transmitter to be installed. sensor rubber washer flat washer jacket nut protective cap 4 Insert sensor into the corresponding location of the tire valve, and then be fixed by jacket nut. 5 Pay attention to avoid the location of transmitters when install rubber tire.
Receiver installation steps: 1 Take out receiver, receiver paste board from the box. 2 Tear up the adhesive protective film on paste board, stick the receiver on the selected position, adjust the position of the receiver in order to help the driver read the display information on the LCD screen. T M L OK 3 Connect the power anode with ACC ignition wiring, cathode with the vehicle power ground. To ensure that the power connection is correct and the input power is 12 ± 4V DC power.
Operation System Introduction After the receiver power wiring is connected, the vehicle ignition switch turns on, the system start self-checking. LCD screen light up all the display information ,at the same time buzzer starts buzzing.
After self-checking passed, the system enter into tire checking status display, (below) normal work interface, if the self-checking does not pass, buzzer start buzzing and LED light lights up. [ Note ] ： The system will displays the data it stored last time when turning on the ignition switch after the automobile being parked a period of time, and will refresh in one minute when the speed of the vehicle arrive 20 km/h.
System Settings In normal working mode,press key for 3 seconds to enter into the menu settings interface,press and then press key can switch between ~ key can enter into corresponding function settingmode or press for 3 seconds to exit from the interface: ( Tire information display setting) 1 Press key to select function display mode 。 key to enter into information display setting 2 Press mode,show / ,and the interface continue flashing, indicating that the new settings can be carried out.
(Units display settings) 1 Press key to select function display mode 2 Press key to enter into unit display setting mode,press 3 Press key to select pressure unit / / . key to complete the pressure unit setting,and enter into temperature unit setting. 4 Press key to select temperature unit 5 Press Key To Save Settings Or Press / Key Not To Save The Settings, And Return To The Current Display Mode .
(Pressure and temperature limits setting) 1 Press key to select function display mode 2 Press key to enter into pressure, temperature alerting limit setting mode, press key to select / . (the factory default settings / user-settings).
4 After select ,press key to operate self-setting limit (defaulting select the first number of high-pressure limit), press key to select setting position, the selected position will keep flashing until the next position is selected by pressing Press key. key to adjust the size of flashing bit values until the last high-temperature limit is set up,.
(Tire ID exchange setting) 2 Press key to select function display mode Press key to enter into the tire ID exchange mode, press key to select the tire, selected tires keep in flashing state. 3 Press key, the No. on corresponding location of selected tire starts flashing, press key to adjust( ~ ) to the No. which in corresponding location of tire with the needs of exchange.
(Tire ID No. read setting) Before system work properly, the tires ID No. need to be read, then the transmitter can send data to the receiver real-time. 1 Press key to select function display mode key to enter into the tire ID No. read mode, press 2 Press key to select the tire, selected tires keep in flashing state. 3 Press key, the No. on corresponding location of selected tire start flashing, waiting to receive the ID signal.
Finish learning of other tires according above steps [Note] ID No. studying has been completed before leave factory, please follow the transmitter stickers to install. Tire ID No. studying, relative atmospheric pressure is＞/ = to 60kPa, the deflation is 30kPa in 1 minute. (Spare tire activation settings) 1 Press keys to choose function display mode 2 key to enter into spare tire setup mode ,display Press / , and continue to winkle, indicating that the new settings can be carried out.
Common Alerting Mode Fast leaking alerting, buzzer buzzing, pressure warning light flashing. High pressure alerting, buzzer buzzing, pressure warning light flashing. High temperature alerting, buzzer buzzing, pressure warning light flashing. Low pressure alerting, buzzer buzzing, pressure warning light flashing.
Transmitter failure alerting, buzzer buzzing Low voltage alerting, buzzer buzzing No signal alerting, buzzer buzzing * Alerting default limits Low pressure alerting High pressure alerting High temperature alerting ≤190 kPa ≥330 kPa ≥80℃ [Notice]①If the alerting state displays, please solve the problem in time, which could save transmitter power consumption. ②In alerting state, press any button to stop alerting sound.
Troubleshooting Failure phenomenon Possible reasons No power Be ensure that cathode and anode power supply connection and grounding are correct.
Disclaimer 1 Except the installation methods mentioned in user's manual, any changes in product installation and product structure are not allowed. 2 In order to avoid damage to the system, please do not open the product , all the relevant technical services staff should be professionally trained, if the tires have to be disassembled, please note that do not damage the transmitter. 3 This product can effectively monitor the tire, but we can not guarantee any unexpected accidents.
Equipment Connection Receiver Paste board GND ACC Left front wheel transmitter Right front wheel transmitter Left rear wheel transmitter Right rear wheel transmitter The first edition (April，2009) We do not notice when there is an upgrade FOUYOU Group CO，Ltd has the power of final interpretation.
rd floor, Foryou Tower, Yanda yi road, Huizhou, Guangdong Province,China http://www.foryougroup.com E-mail: AEsales@foryougroup.
